Search Documents

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this work was to assess the influence of parameters such as residence time, solid content, and temperature in a process route towards purified rare earth liquor which could be adequate to produce marketable rare earth products. The steps of the process route proposed in this study comprised water leaching of a sulfated rare earth ore and removal of impurities through the purification of the rare earth sulfuric liquor, which is the product of the water leaching step. The sample used in the water leaching experiments was a sulfated rare earth ore produced by the reaction of a beneficiated rare earth ore with sulfuric acid followed by roasting at 700 °C for 2 h in a muffle furnace and cooling at 20 °C. The water leaching experiments showed that the best condition comprised a residence time of 30 min, temperature of 20 °C, and solid content of 10% w/w, resulting in a recovery of 71.3% of the rare earth elements (REE) and a lower impurity extraction, e.g., only 15.0% of Fe, representing the main impurity in the rare earth ore. Even when presenting low amounts of impurities, the rare earth sulfuric liquor still needed to be purified before it can be used in the production of marketable rare earth products. In the study, the rare earth sulfuric liquors were purified in two consecutive neutralization steps, first by dosing the limestone pulp to pH up to 3.5 and secondly by adding the lime pulp to raise the pH from 3.5 to 5.0. The application of two consecutive purification steps at 20 °C resulted in the highest overall REE recoveries (65.4%) throughout all the steps of the process, being 71.3% in the water leaching, 99.6% in the partial purification with limestone pulp, and 92.1% in the purification with lime pulp at 20 °C. Under this condition, there was a total elimination of Fe, P, and Th and a significant reduction in the Al, U, and sulfate concentrations in the purified rare earth liquor. The purified rare earth liquor attained through the experiment is expected to be amenable to be used in the production of marketable products due to the lower impurities/REO mass ratios.

By Roger Best

In the mining industry, where some of the vehicles are larger than a one-story house, tire maintenance cannot be accomplished by the tire shop alone. It takes an army of people to maintain a fleet of 100 trucks that may be transporting gold, iron ore, oil sand, copper or coal from an openpit to a refinery and eventually delivering the product to a customer. Everyone working in and around these mammoth machines has a duty to help with the maintenance of the tires, whether they know it or not. These responsibilities comprise observation and reporting hazards up to and including changing out a tire and recording the information in a tire-tracking program such as TreadStat.

Jan 2, 2010

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By Paul Zick

The Port Authority of Allegheny County North Shore Connector (NSC) Project involves TBM excavation of twin 690 m (2,240 lf) precast segment lined light rail tunnels through soil and rock under the Allegheny River and a narrow, downtown city street. The $435 M project is funded 80% ($348 M) by the Federal Government, 17% ($72.5 M) by the State of Pennsylvania and 3% ($14.5 M) by Allegheny County. Along the tunnel alignment are a historic building on shallow foundations, modern buildings on deep foundations, and one building constructed directly over the alignment. The project includes construction of twin 369 m (1200 lf) cut and cover concrete box tunnels and an underground station shell. This paper provides an overview of general site conditions, current project status and construction challenges for the Twin Tunnels and North Shore Light Rail Station.

By Yun Bai, Sarah Wilson, Michael Salcher, Mark Trim

Over the last decade more than 62 miles (100 km) of civil transport tunnels were constructed in Sydney, Australia, using the sequential excavation method (SEM). The WestConnex motorway tunnels, each stage of which used over 20 roadheaders to excavate up to 40 tunnel headings, had numerous caverns up to 100 feet (30 m) wide and 82 feet (25 m) high. SEM tunnels in North America typically have far fewer active headings. This paper examines the differences in scope and risk allocation for construction phase services, including comparison of the Permit to Tunnel (PTT) process in Australia and the Required Excavation and Support process in North America.

Jun 23, 2024