Search Documents

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By J. Klemenic

This paper presents an analysis of gold production and prices over an extended period. Production patterns are provided for the world as a whole and for the five major producing countries. Gold prices as a function of interest rates, as measured by municipal bond rates, are given for the period 1947 to the present. World gold production has had a phenomenal increase since 1980, with the exception of South Africa, all major producing nations participated in this increase, even though the price of gold generally has been decreasing since the high level attained in 1980.

Jan 1, 1993

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By Mahesh C. Jha

Cyanidation has established itself as the main process for extracting gold from ores in this century. However, many ores exhibit refractoriness to the conventional cyanidation process. The main cause of the refractoriness is generally the presence of carbon, tellurium, and sulfides, particularly those of antimony, arsenic, and iron. The problem is usually solved by either modifying the cyanidation conditions or providing an oxidation pretreatment. This paper presents results from studies that help in understanding the causes of refractoriness of various gold ores. This is followed by a discussion of many processes that have been developed to solve the problem such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, and pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation.

Jan 1, 1986

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper presents a concise procedure for an improved design of room-and-pillar coal mines. Developed as a result of a three-year research effort, the methodology includes essentially three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and pillar coal mining in the United States. It is shown that the presented approach will lead to a greater recovery of coal by a more economical, yet safe, mining operation. Design charts and tables are presented and a step-by-step design procedure for practical mining engineers is explained. Several examples are included demonstrating the use of the proposed design procedure for room-and-pillar coal mines.

Jan 1, 1983

By C. E. Capes

The spherical agglomeration process provides an attractive method for the cleaning and recovery of fine coals in the form of compact oil-bonded pellets. In treating a washery effluent containing 50% minus 20 micron material by this technique, the slurry was first mixed under vigorous agitation with oil to deash and dewater the fine coal. The flocculated coal pulp was then formed into larger agglomerates on a modified balling disc. The operation of a semi-pilot scale process is described and an analysis of some of the operating and system variables is given. A semi-theoretical expression to predict the final agglomerate size under various conditions is derived and compared with the experimental data. Coal producers are faced with a growing requirement to clean and recover fine mesh coals. Greater mechanization of the extractive and preparation processes has resulted in finer-sized products containing larger quantities of associated foreign matter and preparation plant effluents contain quantities of fine coals which are potentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product(1)

Jan 1, 1970

By R. Tamir

This paper will describe the benefits of utilizing the decision support system, DSS to support the methodology of structured decision-making in the mining environment. It will outline the layers of the mining related decision making – 1. Creation of “one truth” situational awareness utilizing 2. existing planning, ERP, operational and monitoring agents, a. Expressing plan verse performance across mining phases and functions compared with the actual and trends to evaluate performance. b. Creating alternate courses of action and the implications up and downstream. 3. It will review the current condition were although a multitude of technologies resolve multi variable issues they do not interact in a way that assists decision makers throughout the organization in making high-quality decisions that will push the overall performance envelope. 4. The paper will show the benefits of integrating military methodologies to resolve multi variable complexed issues (operational, financial and other), operating in changing environments in order to meet time sensitive objectives with restricted resources. This is achieved by creating a shared situational awareness thru incorporating information from a multitude of data generating agents, creating COA, selecting the appropriate and turning it into a plan. The paper will discuss the implementation and suggest a path.

Feb 1, 2023

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. Alternatively, the organic efficiency parameter does consider process economics; however, it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach is introduced which reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure which reflects a better use of performance data. INTRODUCTION Partition curves are commonly used in the characterization, evaluation, and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, and density separators. Graphically, the partition curve depicts the recovery of particles as a function of a physical property on which the separation is based (e.g. particle density, size, magnetic susceptibility, etc.). Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic “S” shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout (or bypass) values, the midpoint slope, and the separation cut point (property value with 50% recovery). Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of the calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, since a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point (i.e. an infinitely large slope). One common formulation of this slope, the Ecart Probable (Ep), is derived by evaluating the slope between the 25% and 75% recovery points:"

Jan 1, 2015

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

Conventional wisdom in the mineral processing industry leads one to believe that pressure oxidation of refractory carbonaceous (preg-robbing) ores is not a practical approach to process development. Initial acid pressure oxidation testing on carbonaceous sulfide ores at the Twin Creeks Mine supported this conventional wisdom. After testing other refractory process options, including air and oxygen enriched roasting, Santa Fe Pacific Gold decided to take a second look at pressure oxidation, using conditions outside the normal range of conventional practice. A combination of very fine grinding and high operating temperature and pressure resulted in significant increases in gold extraction. This paper details the effect of operating parameters developed for Twin Creeks on gold recovery, sulfur oxidation, carbon oxidation/passivation and preg-robb through the laboratory and pilot plant investigations.

Jan 1, 1995

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By Lynda T. Holden, Philip L. LeHoux

Barneys Canyon Mine is a 1.8 million t.p.y. gold heap leach operation near Salt Lake City, Utah. The gold recovery plant has been operating since September of 1989. Carbon elution is done at atmospheric pressure with a high temperature caustic solution. No cyanide is used in the process. Operating experience is discussed.

Jan 1, 1990