Search Documents

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By Kendall Y. Onstott

The paper presents the results of a plant test using WEMCO 1 + 1 enclosed flotation machines for inert gas (nitrogen) flotation of by-product molybdenite from copper sulfide concentrate. Copper depressant consumption in the rougher flotation stage was reduced by 68% as reagent consuming oxygen was removed from the flotation air. Unlike other nitrogen flotation systems used in the industry, nitrogen is recovered above the flotation cells and from froth in tails and concentrate streams and recycled, resulting in minimal nitrogen makeup requirement.

Jan 1, 1984

By George S. Koch

We evaluate the exploration effort by diamond drilling for zinc in central Tennessee and southern Kentucky through a statistical analysis comparing the Middle Tennessee district with the older Tri-State and Upper Mississippi Valley districts. All of the ore deposits are of the Mississippi Valley type and are similar geologically. Through statistical analyses we attempt to answer these questions: Had the drilling density in the Middle Tennessee district been applied to the Tri-State district, how much of the ore in the Tri-State would have been discovered? Had this drilling been done in the Upper Mississippi Valley district, how much of the ore in that district would have been found? Which of these two older districts does Middle Tennessee more closely resemble in intensity of zinc mineralization? Is more drilling warranted in the Middle Tennessee district? Our data base includes tonnage and area distributions of ore deposits in the Tri-State dis¬trict, sizes of ore bodies and probabilities of their recognition in the three districts, and data for the Elmwood mine in the Middle Tennessee district. Our statistical analysis considers the consequences of drilling holes in the three districts on square grids at coarse, intermediate, and fine spacings. We conclude that the drilling pattern assumed for Middle Tennessee would have found some but not all of the ore in the two older districts. We believe that in intensity of mineralization Middle Tennessee more closely resembles the Tri-State than the Upper Mississippi Valley district, and that more drilling is warranted in the Middle Tennessee district.

Jan 1, 1979

By Chris McKee

Quartz has been of interest in occupational health for years because it can cause silicosis after prolonged exposure. New OSHA regulations (Air Contaminant; Final Rule) list perlite as a nuisance dust. They conclude that perlite is nontoxic when air-borne total particulate concentrations are 15 mg/m3 or below and when quartz content is less than 1% crystalline silica. OSHA has established an 8-hour PEL of 15 mg/m TWA for total perlite dust containing less than 1% quartz. OSHA has established a 5 mg/m3 TWA PEL for respirable perlite. These limits will protect workers from significant risk of eye, skin, or other physical irritation. This regulation is based on a Group 2A classification as a probable carcinogen in humans, at the 0.1% crystalline silica level, by the International Agency for Research on Cancer (IARC 1987a, b). IARC found sufficient evidence for carcinogenicity of crystalline silica in animals and limited evidence in humans. Perlite is not listed as a carcinogen by OSHA or the National Toxicology Program.

Jan 1, 1990

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By John A. Reeves

The unit-train concept of moving raw materials .is considered by many railroad men as the most signifigant contribution to reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling results in the maximum utilization of equipment. For example before the unit train was plaged in servige on coal hauled to one of Mid. Continent's customers, about 900 cars and 9 locomotives were needed to move the coal requirements for this plant, compared with. 250 cars and 6 locomotives used by the present scheduling of unit trains. If the economics of unit-train movements are to be achieved, coal companies no longer can use railroad cars as small storage bins on wheels to accumulate their coal in trainload shipments, but, rather, must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time. In this manner railroad equipment is operated at a high degree of efficiency 'with consequent dollar savings. After negotiations between Mid-Continent, the customers and the Railroad, it was decided a unit train loadout and storage facility at Carbondale was required in order to reduce the delivered price of coal to the customers and thereby contribute to the reduction in the cost of manufacturing steel. Carbondale was selected as the bin site location, because the cost of constructing a railroad to Redstone could not be justified for the tonnages anticipated.

Jan 1, 1969

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

By O. Ozdemir

Soda ash, an essential raw material for major industries, such as the glass, chemicals, soap and detergents, pulp and paper, mining and water treatment industries, is traditionally produced by chemical and thermal treatment of trona ore. The treatment processes for trona ore are not only chemically expensive but also energy intensive. Hence, the production of a high-purity trona concentrate at a lower energy and operating cost is of considerable interest to the trona industry. In this study, we describe a possible two-stage process for concentrating trona ore, involving dry magnetic separation followed by flotation, to remove insoluble impurities from the trona ore. The results showed that a trona concentrate of 91.7% purity with a recovery 91.1% can be obtained by two-stage magnetic separation, which could be further improved to 98.1% purity at a recovery of 83.8% by subsequent flotation of the non-magnetic trona product. The purity of trona concentrate is limited by the particle size and impurity content of the trona ore. The operating parameters for magnetic separation and flotation have been identified to obtain an acceptable quality concentrate.

Jan 1, 2011

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By Y. Guo, C. Cao

"China is rich in tungsten resource, but they are mainly associated minerals. The similar flotability of scheelite, fluorite, and calcite resulted in the difficult separation by flotation. This work summarized the current situation and the development of flotation reagents, technological process, and mineral processing equipments in China. Fatty acid served as the collector and water glass was the depressant to expand the flotability differences in traditional flotation technology. However the water glass inevitably influenced the flotation of tungsten minerals to a large extend, and the suppressed fluorite was difficult to recover by flotation. Abundant water glass lead to the bad settleability of the tailings and the tail water was difficult to circulate, resulted in serious environmental problems. Recent study proved that the selectivity of benzene armour hydroxyl oxime acid (BAHA) salts was adequate for the separation of tungsten minerals from fluorite, calcite and most silicate minerals without any depressant. By this way, sodium silicate was canceled completely in tungsten flotation, greatly improving the recovery of tungsten and the environmental problems caused by tail water treatment would be solved fundamentally. TUNGSTEN RESOURCES AND DISTRIBUTION IN CHINA China is rich in tungsten resources and the proved reserves accounted for 60% of the world's reserves [1]. However the wolframite has been dried up and the scheelite resources had become the main resource of the tungsten metal. Table 1 showed the most large and superlarge scheelite deposits in China. China has more than 40 large and superlarge scheelite deposits and the total metallic deserves is more than 3 million ton [2]. But most of the deposits were low-grade and the associated relationship was complicated. For example, scheelite was usually associated with wolframite, molybonite, bismuthinite, pyrite, fluorite, and calcite in Shizhuyuan and Yaogangxian mine."

Jan 1, 2016

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

By A. W. Khair

Surface subsidence is a phenomenon mainly associated with longwall mining, although it can also occur if the coal pillar left to protect the surface deteriorates with time and results in the collapse of the room and pillar system. A method has been developed that utilizes physical mine models and laser holographic interferometry. This method is capable of measuring displacements as small as 5 micro- inches by means of generating displacement contours on a surface, even that of granular materials. Analysis of subsidence in room and pillar mining using models of various extraction ratios ad overburden depths along with two different types of overburden model material (sand and gelatin) has been made. The sand represented the extreme brittle conditions of geologic material while the gelatin represented visco-elastic behavior of geologic material. This paper deals with the analysis of data which has been gathered up to date, and mainly associated with the use of sand as an overburden model material. The analysis included the effect of variation of geometric parameters on surface subsidence. Among these parameters are: variation in seam depth and thickness, surface and seam inclination, and extraction ratio.

Jan 1, 1984

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By G. A. Hayes

The range of gold ores tested at AMMTEC LTD over several years has resulted in the requirement to analyse for the mode of occurrence of gold in order to assist selection of ore processing options. The aim of this paper is to describe the laboratory testwork and analytical procedures which have been of benefit in detail­ing the mode of occurrence and mineral associations of gold and hence being of value in developing an optimised ore processing route. The range of ore and mineral assemblages described include relatively simple pyrite and free milling ores, more complex pyrite plus arsenopyrite gold ores and the quite com­plex associations of gold in copper bearing ores or with car­bonaceous mixed sulphide ore assemblages. The aim of this paper is to describe the laboratory testwork and analytical procedures which have been of benefit in detail­ing the mode of occurrence and mineral associations of gold and hence being of value in developing an optimised ore processing route. The range of ore and mineral assemblages described include relatively simple pyrite and free milling ores, more complex pyrite plus arsenopyrite gold ores and the quite com­plex associations of gold in copper bearing ores or with car­bonaceous mixed sulphide ore assemblages.

Jan 1, 1996

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By J. Morris

Petro-diesel is a common collector for fine coal froth flotation but partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DRO. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAHs were measured in tailings and concentrate streams, and coal recovery and ash rejection were tracked. Results show that concentrate waters consistently had higher DRO than tailing waters, and DRO in both streams generally increased with increasing diesel dosage. DRO again appeared to be limited to the WSF and PAHs tended to partition proportionately with DRO. Results indicate optimal flotation performance should generally coincide with minimal DRO partitioning to process waters. Under typical operating conditions residual DRO should not present an environmental concern; however, conditions should be avoided that allow significant overdosing of diesel.

Feb 23, 2014

By X. Zhu, Chen. L., R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study is to develop a suitable flow sheet to extract rare earth elements (REEs) from coal ash. A total of 14 coal samples of different ranks were examined for REE concentration, and an anthracite coal sample with the highest REE concentration of more than 700 ppm in the coal ash was selected for REE extraction tests. This paper reports on the results of the experimental program completed in the first part of the study, which included hightemperature leaching with nitric acid followed by solvent extraction tests using various organic extractants, namely, tributyl phosphate, Cyanex 572, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and their combinations. A 4×2×2 experimental design was used to conduct a total of 32 high-temperature leaching tests by varying acid molarity at four levels, solids content at two levels and leaching time at two levels. The highest recovery rates of 90 percent for light rare earth elements (LREEs) and 94 percent for heavy rare earth elements (HREEs) were obtained from the optimum leaching test conditions while maintaining impurity recovery to the leachate at less than 40 percent. D2EHPA was found to be the best extractant in this solvent extraction test series, providing an REE recovery rate of nearly 99 percent.IntroductionGlobal demand for rare earth elements (REEs) and other strategic metals is increasing rapidly due to their use in a variety of advanced technological applications, with more than 100 kt of rare earth oxides used worldwide on an annual basis. The United States has less than 10 percent of the world reserves of REE mineral deposits, and in 2013 imported more than 60 percent of its rare earth oxides from other countries, mainly China (United States Geological Survey, 2017). China’s institution of export quotas has significantly reduced supply to the United States, raising the urgency of finding new ways of producing REEs and/ or substitutes. Coal combustion byproducts, which are usually discarded as waste materials, are known to contain REEs in low concentrations that could be extracted with a suitable process flow sheet. This may be a worthwhile route to pursue, considering the short supply of rare earth minerals and the abundance of coal ash in thousands of ash ponds in the United States. More than 110 Mt of coal combustion byproducts are produced annually in the process of satisfying the country’s need for electricity (American Coal Ash Association, 2016), and less than 50 percent of these byproducts are being successfully used in various applications, with the remainder dumped as waste materials in landfills and ash ponds."

Jan 1, 2017