Search Documents

By Siqing Liu

A low-grade cassiterite-magnetite ore from Sichuan province, China, is finely disseminated, assaying 0.39% Sn and 23.20% Fe, respectively. Mineralogy studies show that the fine-sized cassiterite is mainly disseminated in iron minerals and gangue. Moreover, the embedded size of cassiterite is very fine and must be ground to -0.01 mm to achieve a degree of liberation of about 90%. Therefore, fine grinding needs to be conducted to get a high quality tin concentrate and a great loss of tin cannot be avoided when treating the ore by gravity concentration. Based on the above facts, a two-stage separation, with a low intensity magnetic separator and a shaking table, was selected to test the ore. Compared with other similar plants, a relatively good separation has been achieved. Three acceptable products for smelters were obtained as following: iron concentrate assaying 61.69% Fe with a recovery of 75.09%, tin concentrate assaying 27.21% Sn with a recovery of 56.97% and a sulfur concentrate assaying 40.86% S with a recovery of 32.03%, respectively.

Jan 1, 2011

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By L. A. Panek

A new pillar strength formula is presented, incorporating a function P of size and shape, which takes into account the size-shape interaction effect as well as the enhanced strength exhibited by wide pillars. Existing pillar formulas, lacking these capabilities, are not suitable for extrapolating small-specimen test results to mine-pillar sizes and shapes. Interpreting compressive-strength test results as function of P clearly reveals wide-pillar behavior in much old test data. Model relationships are discussed, along with their scaling implications.

Jan 1, 1994

By M. Sears, W. H. Su, J. Wickline, M. A. Van Dyke, G. Esterhuizen, Z. Khademian

It is commonly recognized that seismicity can be induced by rock failures or slip along geologic structures around mining excavations. The unpredictable nature of these events and their proximity to the working area may raise safety concerns in underground mining operations. Modeling can be a useful tool for estimating seismic potential for a given mine layout, but the challenge is to detect a seismic event and estimate its intensity in the model. One well-documented approach is to monitor the variation in the energy content of the model and record potentially damaging seismic events when there is a significant release of energy. Researchers from the National Institute for Occupational Safety and Health (NIOSH) employed this approach using 3DEC modeling software to simulate the anomalous seismic events that occurred in a deep longwall mine in Virginia in 2005. A four-panel model of the mine was constructed utilizing a 2D cross section at the location of the mining face at the time of the event. Seismic potentials associated with the development of each panel are evaluated by recording the seismic energy released during the simulation. The results demonstrate the occurrence of two relatively significant events during the mining of the last panel, which are consistent with the historical observations at the mine.

Apr 26, 2022

By T. W. Camm

Some of the defining characteristics of narcissists include a grandiose sense of self-importance, preoccupation with success and power, a sense of infallibility, and a supreme confidence in their ability and intelligence. Ironically, many of these characteristics are rewarded in business organizations, which may explain why there seems to be so many narcissists in management positions. Assuming we will be dealing with narcissists throughout our career, it makes sense for us to understand what makes them tick, and more importantly what we can do to work with them in a constructive manner.

Feb 23, 2014

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party's mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By Larry A. Enloe

The 16-to-1 milling operation is Sunshine Mining Company's first new silver and gold producing facility. The 16-to-1 underground mine and mill are located approximately 64 km (40 miles) southwest of Tonopah, Nevada. Ore re- serves in the epithermal vein deposit are estimated at 0.91 Mt (one million st) of ore, at an average silver grade of 206 to 240 g/t (6 to 7 oz/st) and an average gold grade of 1.2 g/t (0.035 oz/st). The underground mine uses a large diameter blasthole stoping system of mining using highly mechanized rubber-tired equipment. The mill uses conventional cyanide leaching with countercurrent decantation and Merrill-Crowe precipitation. The mill start-up was in February 1982 resulting in the first pour of dore' in March 1982. The mill's present annual production is approximately 31.1 t (1.0 million oz) of silver and 264 kg (8500 oz) of gold.

Jan 1, 1984

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By W. R. Reed, J. D. Potts

This study tests the ability of a new air nozzle system, located under the drill deck shroud, to improve the dust capture of the drill deck shroud. The system consists of three air nozzles supplied with regulated pressurized air and located midway down the shroud in the off-inlet corners of the shroud. Laboratory testing produced operating curves for the system that showed an optimum operating point of 207 kPa (30 psi) and generated respirable dust reductions of 48% to 52% from the drill deck shroud.

Jan 1, 2009

By C. M. Bristow

The mineral kaolinite is one of the commonest minerals in the uppermost 10 m of the continental crust; ranking in abundance alongside minerals like quartz, mica, feldspar and calcite. Only very exceptionally does it possess all the necessary properties needed to make it worth commercially exploiting. The terms 'Kaolin' and 'Kaolinite' are derived from a locality known as 'Kau-ling', in Jiangxi Province, Peoples Republic of China; where samples of a white clay used by the Chinese to make porcelain were first obtained by European missionaries and explorers in the eighteenth century.

Jan 1, 1986

By S. Frimpong, E. Siami-Irdemoosa, S. R. Dindarloo

"Electric and hydraulic shovels are the dominant loading machinery in surface mining operations. Despite their critical role in production and their high capital and operating costs, no reliable and comprehensive quantitative performance metric is available. In this paper, a stochastic shovel effectiveness (SSE) measure is proposed for the purpose of quantifying the performance effectiveness of these shovels. The SSE is based on the widely used method of overall equipment effectiveness (OEE) in the manufacturing industry. The OEE measures the performance effectiveness of equipment by multiplying its mechanical availability, utilization and production quality. In manufacturing processes, quality rate is the ratio of the total number of products minus the number of defective products – equivalent to the number of acceptable products – to the total number of products. The SSE similarly uses the mechanical-availability and utilization terms, but instead of quality rate it uses a new parameter named bucket rate.The variability or randomness of the input data, that is, availability, utilization and bucket rate, are further incorporated into the SSE, and a final stochastic SSE distribution is derived in the form of a probability density function. One hydraulic and one electric shovel in a surface mining operation were selected to test the validity of the proposed method. The SSE scores for the two shovels, operating continuously for one year, were derived and compared. As with the OEE, the three-parameter SSE method yielded more representative results for overall performance measurement than a single-parameter approach. Using Monte Carlo simulation, a three-parameter Weibull and a normal distribution were derived for quantifying the overall effectiveness of hydraulic and electric shovels, respectively. As a decision aid, the proposed methodology promises to render a more informative tool than traditional metrics for mine equipment maintenance and management."

Jan 1, 2015

By P. K. Kankar, Manoj Khandelwal, Ramesht Shukla

One of the utmost severe mining catastrophes in underground hard rock mines is rock burst phenomena. It can lead to damage to mine openings and equipment as well as trigger accidents or even threat to life as well. Due to this, a number of researchers are forced to study some easy-to-use alternative methods to predict the rock burst occurrence. Nevertheless, due to the extremely multifaceted relation between mechanical, geological and geometric factors of the mines, the conventional prediction methods are not able to produce accurate results. With the expansion of machine learning methods, a revolution in the rock burst occurrence has become imaginable. In present study, three machine learning methods, namely XGBoost, decision tree and support vector machine, are utilized to predict the occurrence of rock burst in various underground projects. A total of 134 rock burst events were gathered together from various published literatures comprising maximum tangential stress (MTS), elastic energy index (EEI), uniaxial compressive strength and uniaxial tensile stress (UTS) that have been used to develop various machine learning models. The performance of machine learning methods is evaluated based on the accuracy, sensitivity and specificity of the rock burst prediction.

Mar 17, 2021

By V. Aghazadeh, E. Bidari, M. Aazami

In this study, mineralogical and microanalysis characterization, as well as diagnostic leaching and cyanidation tests, were performed to gain a better understanding of the refractory nature of the arsenical zone of a Carlin-type gold deposit and also to evaluate possible treatment routes to maximize gold recovery. The results obtained showed that only 56% of the ore’s gold content is amenable to direct cyanidation. The majority of the remaining gold was found as submicroscopic gold and in association with sulfide minerals, such as orpiment, pyrite, and sphalerite. It was also found that despite the abundance of silicate and carbonate minerals in the arsenical zone, they do not play a key role in the refractory nature of the ore, and gold can be liberated from such minerals by appropriate grinding. The analyses further revealed that orpiment dissolves readily during cyanidation, and this dissolution retards the kinetics of gold extraction. Pyrite and sphalerite were generally found to occur in fine network texture and in association with quartz. Flotation of such auriferous sulfides may be difficult due to their oxidized surface. Fine grinding (−20 μm) was found to be partially effective in improving gold extraction.

May 28, 2020

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020

By J. D. Miller

Many factors -- political, environmental and technological -- will determine the extent to which the United States realizes the potential of its vast coal resources. Not the least of these factors is technogical development including mining, processing and transportation. With regard to processing technology, about 50% of the 800x106 tons of coal mined annually in the U.S. is processed in preparation plants. The purpose of the physical separations accomplished in these preparation plants is to remove ash (present as clays and other oxide minerals) and sulfur 'present mostly as pyrite). Coal flotation circuits for such separations are becoming more important in the processing of minus 28 mesh coal. (1,2,3) For example in the U.S. in 1960, 31 flotation plants processed 26,500 tpd; whereas in 1980, there were 80 flotation plants which processed 78,300 tpd. This corresponds to an annual growth in flotation plant capacity of 10 per year during the past two decades. Coal flotation is based on the natural or induced hydrophobicity of coal particles which are separated from hydrophilic ash and sulfur constituents by attachment to air bubbles. The coal particle/air bubble aggregates are collected in a froth phase which is created by the addition of a suitable frother such as MISC. Without exception, such separations are made in a conventional flotation cell, which, in essence, is a stirred tank reactor with a shrouded rotor to shear the air as it passes through a hollow shaft. The dispersed air bubbles (4.0 mm diameter) are stabilized by addition of the frother. Collision of the air bubbles with, and/or precipitation of the air bubbles on, the coal particles results in the formation of coal particle/air bubble aggregates which rise in the gravitational field and are collected in the froth phase developed at the top of the flotation cell. Restraints on successful separation by this conventional flotation technique are particle size and retention time. Generally it is found that effective flotation is only achieved for particle sizes between 10 and 1000 microns. Further, with respect to retention time, it is found that a nominal retention time of at least 2 minutes is required for successful separations. These facts limit the effectiveness of conventional coal flotation. Coal fines may be lost in the reject stream and disposal is frequently a problem. The retention time required for conventional flotation results in large floor space demands which limit the capacity of the plant.

Jan 1, 1981

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026