Search Documents

By Thomas C. Shrake

The Lomas Bayas copper property is located93 km (58 miles) east of Antofagasta, Region II, Chile (Fig. 1). The deposit was discovered in 1880. The deposit produced intermittently until 1992. Production at Lomas Bayas took place in high-grade veins and breccias mined underground. During 1991, Empresa Minera Mantos Blancos SA (EMMB) optioned the property from Compania Doña Ada SA. Doña Ada maintained the right to continue mining the ores by open-pit and block-caving methods and hauling the ore to its plant located60 km (37 miles) to the north. EMMB conducted exploration and column test programs. On May 9, 1994, Compania Minera Gibraltar Ltda.(CMGL) signed a purchase option agreement to acquire the Lomas Bayas property. CMGL conducted 8,612 m(9,490 ft) of reverse-circulation drilling, 2,028 m (6,650ft) of diamond drilling, a series of metallurgical tests and geologic mapping. The company then decided to exercise its purchase option.

Jan 1, 1996

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By T. Faulkner, S. A. Richards

"The Scale-Distance formula is one of the primary means of determining the maximum amount of explosives that can be safely detonated at one time by a single delay. This paper describes a method of applying the Scale-Distance formula to the entire mining area using gridded surfaces. Using this technique, the operator can better determine the economic impact of nearby structures on the mine plan. INTRODUCTION As the surface mining of coal and stone encroaches near populated areas, precautions must be taken to minimize blast vibration damage to protected structures. The common method employed to minimize vibration damage is not to reduce the total amount of explosive in the hole (which would negatively affect fragmentation), but rather to introduce delays to reduce the amount of explosive detonated at any point in time. The Scale-Distance formula, an industry-accepted standard, may be used to calculate the maximum weight of explosive that can be detonated at one time without damaging the structure. This information may then be used to determine the number of delays required for each hole. Detonators make up a large part of the cost of blasting. At roughly $15 per detonator an additional detonator in the hole can be significant. It is normal to set off hundreds of holes at in one shot. An additional detonator in each hole can cost additional thousands of dollars per shot. The number of detonators is also a function of the depth of the holes and the hole spacing. Being able to accurately forecast the economic impact of blasting near structures improves a company’s ability to make informed decisions on how to approach property owners. Operators basically have three options when dealing with property owners: 1. Buy the property and blast without restriction 2. Negotiate with property owner for a waiver to allow unrestricted blasting 3. Comply with the legal blasting restrictions This paper proposes a method for the engineer to forecast for all points in the proposed mining area the impact of nearby structures upon the blast design. Being able to create a contour map and ultimately estimate the number of delays required for the entire forecasted mining area, the engineer can create accurate economic forecasts of the cost of blasting. The objective is to reduce the level of uncertainty in the forecast of the blast component portion of the forecast."

Jan 1, 2016

By David Court, Rab Brown

The paper discusses the work in progress on the construction of the extension of the High Speed Rail line from the Channel Tunnel into the centre of London UK known as the “Channel Tunnel Rail Link” (CTRL), and particularly on contract 250 which involves the construction of two 5.3Km tunnels 7.15m diameter constructed with two EPB convertible tunnelling machines underneath the densely populated area of East London. In addition the paper will look at an innovative Alliance that has been formed between the Contractors and the Client’s Engineer involved in the construction of the London Tunnel Contracts

Jan 1, 2003

By Yunxing Cao, Xinsheng Zhang, Bingbing Meng, Shuaifang Guo, Li Wang, Junsheng Zhang

During the initial process of mining a longwall working face, it is often found that the roof will not collapse readily, which increases the risk of later roof collapse disasters. Explosive and hydraulic fracturing are common roof weakening techniques; however, they have certain limitations. In the present study, CO2 fracturing was used for roof weakening during the initial mining phase in the Changcun coal mine, China, which is a novel strategy. First, by analyzing the lithological characteristics of the working face and applying combined beam theory, the breaking spans of the top coal, immediate roof, and main roof were determined before weakening. An F-35 CO2 fracturing device with a rated pressure of 270 MPa was used, which provides fracturing energy equivalent to 0.968 kg of TNT. The fracture radius of the main roof was studied by ANSYS/ LS-DYNA combined with the hanging roof-breaking theory to determine the optimal layout of CO2 fracturing drills. The results show that the breaking spans of the top coal, immediate roof, and main roof were reduced by 3.99 m, 7.66 m, and 22.03 m, respectively. The main roof collapsed as the working face advanced, eliminating the chance of later roof collapse disasters. Compared with hydraulic fracturing and explosives, CO2 fracturing is safer and more practical, giving it significant application potential.

Nov 23, 2023

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Xie Junjie, Li Shina, Ma Ruixin, Min Changli, Yin Zichen, Li Kang, Shi Zhuonan

Cesium and rubidium were effectively separated by zinc ferrocyanide coprecipitation method, and the effect of precipitant addition amount on the separation of cesium and rubidium was studied. Under the conditions of Zn/Cs molar ratio of 0.45 and Zn/Fe molar ratio of 1, the precipitation rate of cesium is 84.01% and the separation factor of Cs/Rb is 164.65. The thermogravimetric curves of the sediment were measured, and the effects of roasting temperature, roasting time, and leaching liquid/ solid ratio on the extraction of cesium were studied. Almost all of the cesium was extracted under optimal conditions: roasting temperature of 600 °C, roasting time of 3 h, leaching temperature of 25 °C, leaching time of 0.5 h, and liquid/solid ratio of 5:1 mL/g. After the leaching process, the leach liquor with high concentration of cesium of 80.17 g/L was obtained. Finally, the leach liquor was further purified by solvent extraction, and the purity of the cesium chloride product reached 99.66%.

Mar 17, 2024

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By JESSICA W. A. AZURE, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

This study developed machine learning (ML) models for predicting rock formation reactive forces experienced by a hydraulic shovel bucket during excavation. To do this, rock formation in the form of muckpile was modeled as granular ball elements in three-dimensional particle flow code (PFC) using linear bonding logic. A typical field-size hydraulic shovel bucket modelled in AutoCAD was used to excavate the rock formation and the three-dimensional shovel bucket resistive forces required to cut through the rock formation were measured and recorded. The experiments involved different muckpile height, bulk densities, repose angles, and average fragment size. Six ML algorithms, artificial neural network (ANN), K-nearest neighbor (KNN), linear, random forest (RF), regression tree (RT), and support vector machine (SVM), were evaluated on their ability to predict the shovel bucket resistive forces. The input variables used for the prediction of the resistive forces were the muckpile bulk density, angle of repose, height, and fragment size. The results showed that the ML techniques are useful and reliable methods of predicting rock formation resistive forces based on the rock formation properties. This research is a preliminary step towards developing reliable models for accurate prediction of excavation forces/torques which could potentially enhance hydraulic shovel process automation.

Sep 27, 2021

By James Wm. White

Today a large number of open pit mines use computer-based mine management systems to automatically assign haul trucks, track equipment, and manage information. Now advances in digital communications allow the use of these systems in underground operations. Underground mine management systems help maximize production by providing impressive gains in areas such as equipment and manpower utilization, draw point equalization in block caving operations, preventive maintenance, and safety. Current systems use allocated or "locked" train and LHD dispatching. While allocated dis-patching rarely optimizes open pit production, it offers an efficient mode of operation underground where options are more limited.

Jan 1, 1996

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

MINExpo International is billed as the largest exposition for the mining and mineral processing industry. And the 2012 edition, scheduled for Sept. 24-26 in Las Vegas, NV, is no exception. Put on by the National Mining Association (NMA), attendance at this year?s show is expected to be significantly more than the 38,500 who attended the last MINExpo in 2008. The exhibit will also be quite a bit larger in 2012 than it was at the previous MINExpo. More than 1,800 companies, representing more than 30 countries, will fill the Las Vegas Convention Center. The more than 850,000 sq ft of exhibit space will include the North and Central halls as well as South Halls Nos. 3 and 4. And the Silver Lot outside of the front door, under construction in 2008, will be filled with more exhibitors. The 2008 show attracted about 1,220 exhibitors occupying more than 600,000 sq ft of exhibit space.

Jan 1, 2012

By David L. Veith

As the basis for the State of Minnesota's Regional Copper-Nickel Study environmental evaluation, hypothetical mine models were developed ranging in ore capacity from 5.35 to 20.00 x 106 mtpy. Open pit and underground mining operations were defined utilizing conventional methods of ore extraction. Processing of the copper-nickel sulfide material involved conventional bulk flotation of the valuable minerals, with maximum water recycle And tailing disposal. Flash smelting and electrolytic refining of the concentrate resulted in 0.10 x 106 mtpy copper plus nickel metal, plus associated cobalt and precious metals. Variations in model parameters allowed environmental trade-offs to be identified.

Jan 1, 1980

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By D. L. McCain

In considering slurry transportation for Consolidation Coal Company's Loveridge Mine in Northern West Virginia, many things were taken into account. The advantages of slurry transportation in comparison to shuttle car, belt and rail transport have been given in previous publications." These include increased safety and the potential for increased productivity. In addition to these considerations, the slurry transport system installed in an existing mine provides an alternate or additional transportation mode to the one already existing. In the Loveridge Mine, this is rail haulage. Since the rail system is a single track system and the distances involved are several kilometers, it is not always possible to provide for haulage of loaded cars, return of empties, supplies and maintenance in an efficient manner. Slurry transport of the coal from the production faces to the preparation plant allows the rail system to fulfill the remaining transportation needs in an efficient manner. Consol initiated development work in slurry transportation in the early fifties leading to the construction and operation of the 174-km (108-mile) Cadiz-to-Cleveland pipeline which carried 1,200,000 metric t/y (1,300,000 t/y) from 1957 to 1963. Development work on coarse coal slurry transportation for underground mines started in 1970 with feasibility tests on coarse coal at Conoco's Ponca City, Oklahoma, slurry test facility. A series of tests were conducted in several locations as development work proceeded on the various subsystems, mechanical equipment and controls required to produce a working system to follow a continuous miner in a room-and-pillar type mine, then to combine the coal production from several mine faces for mainline transportation to the preparation plant. The face system, including the crusher-pump vehicle, hose hauler vehicle, slurry booster pump units, return water unit and 900 to 1,200 m (3,000 to 4,000 feet) of pipeline was brought together for the first time and tested as a system at Consol's Robinson Run Mine in northern West Virginia in 1975. A pipeline wear test at the Loveridge Mine where 300,000 tonnes (330,000 tons) of minus 127-mm (5-inch) run-of-mine coal were pumped from the raw coal bin into the preparation plant and a large scale test in Ponca City on a multiple feed sump where several slurry flows could be combined to provide surge capacity and a constant reclaim rate for mainline transportation completed the preliminary testing for a complete system. A decision was made to commit the system to a mine, and the south half of the Loveridge Mine was chosen. This site required the transporting of coal from one longwall and two continuous miner development faces. To prevent startup and unexpected problems in the slurry system from shutting down production of coal from the longwall face, the rail car loading point from the main section belt was chosen as the feed point for the slurry system and the design would allow for rapidly switching from one transport mode to the other. Scheduling of required development entry work and the developmental nature of the system led to a decision to install only one continuous miner face slurry transport system rather than two for this first system. The type of continuous miner in use at the mine for the foreseeable future was the Joy 2BT6 twin boring machine. This machine cuts a stable, arch-shaped entry and was therefore allowed to mine about 26 m (85 feet) of entry before roof bolting was re¬quired. Since peak production from this type of machine was not high, a smaller transport system could be used with it.

Jan 1, 1981

By John W. Crawford

The title of the paper which I have been asked to present is somewhat misleading it infers in fact that there is a definite coalbed height below which raps or canopies cannot be applied to electric face equipment. Although this may be so with regard to certain pieces of existing equipment under certain conditions, to date we do not have enough experience to determine this magic number. Therefore MESA is continuing to hold the line on the time frames stipulated in Section 75.1710-1 of the Mandatory Safety Standards - Underground Coal Mines, which at this point in time requires these protective structures in mining heights of 60 inches or more. In order to give you an idea why we are taking such a firm stand on this matter, I believe it is necessary to describe some of the background work that was done prior to promulgation of the regulations and to give a resume of our experience since the requirements have become effective. Initially MESA made field investigations of all underground mines to determine what the state of the art was in the use of cabs and canopies for protecting equip¬ment operators from falls of roof. These studies revealed that the application was basically in its infancy and what progress had been made was due to the impetus of the mine operators themselves. Manufacturers of electric face equip¬ment provided these structures only on the direct order from the mining company and built them to their specifications. In talking to the operators and the miners in mines where cabs or canopies were in use, it was the consensus that these structures did improve safety and that although originally there was some reluctance on the part; of the miners to work in the confines of a cab or canopy, mast would not work without them once they had been adapted to the equipment.

Jan 1, 1975

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Clément F. Bernier

One of the chief sources of the world's supply of asbestos lies in a belt of ultrabasic rocks which runs northeastward through an area called the Eastern Townships, south of the St. Lawrence River in the Province of Québec. The productive portion of this belt extends from the town of Asbestos in the south, for a distance of some 9,5 km to beyond the village of East-Broughton. The first discovery of asbestos in this region was made in 1874. Only crude fibre was produced until 1888 when the first mill was erected near the town of Black Lake. Since the inception of the industry, almost 100 years ago, no less than 100 different compa¬nies have been formed and 46 different mines have been operated. There are presently 5 active companies in the area providing direct employment for 4100 workers, down from 6000 during the seventies.

Jan 1, 1984