Search Documents

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By L. Mead

Dimension stone is a natural stone (granite, marble, limestone, sandstone and slate) that can be quarried, cut and shaped to conform to acceptable industry standards for size, consistency and durability. There are numerous outlets for the finished product in exterior and interior architectural and design applications. A continued growth market is with residential usage— particularly in new, upscale construction. This has become a competitive market between domestic producers and lower cost imported products. These imported products have become available at many of the building supply retail outlets and have increased the use of stone in residential construction and renovation. The traditional architectural application of dimension stone is tied to commercial and institutional building construction trends and market. There has been a noticeable increased usage of stone in the Sun Belt. This stone is usually supplied by local fabricating shops. It is used in the exterior and interior of shopping malls. This market generally uses local stone sources. It has increased the demand for sandstone, limestone and quartzite in this region of the country.

Jan 1, 2005

By S. R. Dismukes

Mining is likely to be targeted by The United States Environmental Protection Agency (“EPA”) as one of its key enforcement targets for fiscal year 2002-2003. Identifying the mining industry as an enforcement target, coupled with an increase in enforcement activity in recent years, places each mining operation at increased risk of receiving enforcement attention. A properly developed and implemented Environmental Management System (“EMS”) tailored for your operation is invaluable in reducing the risk of incurring liability for non-compliance. At the heart of an effective EMS is an audit program that checks the company’s compliance with environmental requirements. In addition, audit privilege (in select states), voluntary self-disclosure, and the attorney-client privilege serve as very effective tools for managing those liabilities that may arise during auditing a well-developed program. Of course, these latter tools are effective only if the auditing program is properly structured and properly managed. EPA and some states also provide varying degrees of immunity for environmental violations that are voluntarily disclosed in writing by the company. However, self-disclosure laws and policies typically prescribe stringent requirements for parties seeking to take advantage of them. For example: U.S. EPA has recently extended the time period in which to provide full written self-disclosure to 21 days. However, U.S. EPA’s revised Self-Disclosure guidance also addresses when a company obtains knowledge of a violation for purposes of triggering the 21-day clock and specifically extends the knowledge requirement to include the company’s agents and consultants. This expansion increases the difficulty companies may have in clearly defining and managing when they obtained knowledge. This difficulty increases the importance of managing factual development and the strategic use of other

Jan 1, 2001

By N. S. Kim

Silver paste including nano sized particles maintains conductivity in high temperatures without forming oxide layers. In the industry, printing process produces wasted silver paste inside the cylinder and on silk-screen. Pyrometallugical silver recycling methods have environmental problems and do not extract pure silver after removing polymer and organic materials during the extraction process. In this study a simple wet process, of recycling the waste silver paste, using ammonia, was conducted. Silver ion extraction yield was increased using oxidant in the ammonia solution. Possible extraction yields, such as pH, concentration, temperature of ammonia, oxidant concentration and the extraction time. The particles that were obtained after the extraction process will be used as porous hydrophobic catalytic and applied to AI mask and hydrophobic ink. Keywords: Waste silver paste; Ammonia; Hydrophobic porous support

Jan 1, 2009

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

Talk some about your background. Mining, particularly coal, runs in the family. I come from a mining family, one generation re-moved. Both of my grandfathers worked in the coal mines. My mother?s father had worked as a coal miner in the South Hills area of Pittsburgh after coming to America from Croatia. My father?s father (who died of black lung long before I was born) had been born in America and worked as a mine foreman and superintendent in mines just outside the Pittsburgh area. My father often talked about when, as a child, he accompanied his father underground on Sundays to check the mine pumps. While I never expected to go into mining, I often read some of my grandfather?s books on mining technology that my father had kept. I started college at Penn State and drifted into mining engineering as my third declared major. I was finally realizing the importance of a career choice. I?ve never regretted that decision. One of my children, Mark, has followed me into mining engineering, much to my surprise and pride. Evidently, he had been listening to the many conversations I had with friends and colleagues in the industry and never considered any other career path. He has since married another mining engineer, Kray Davis Luxbacher, so we truly have a mining family and can talk mining when we get together. My other children are in more mundane lines of work and rapidly tire of the mining discussions. I?ve worked for operating companies: Pittsburgh Coal Co. (then a division of Consolidation Coal Co., and a company I believe both of my grandfathers had worked for), Island Creek Coal Co., and a research organization: Occidental Research Corp. I am now with Glenn Springs Holdings Inc., dealing with legacy issues (primarily environmental) related to Occidental?s previous mining operations (coal and minerals). As such, I have a broad view of the industry and the critical changes that are shaping our industry.

Jan 1, 2008

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By P. Bester, G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26million tons of ore of which 16 million is mined and milled onsite. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centred around the Pyroxenite ore. This will lead to substantial increases inproduction costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By W. Randall, Robert M. Leary

Twin 1250 m (4100 ft.) long highway tunnels through Cumberland Mountain near Middlesboro, Kentucky are planned to be completed in the early 1990's. The tunnels will be excavated in sandstones, limestones, and shales, dipping at 35 to 50 degrees and striking nearly perpendicular to the tunnel alignment. In 1985-86 a pilot tunnel was excavated as a crown drift along the alignment of the southbound tunnel. The benefits of the pilot tunnel in reducing uncertainties for main tunnel construction are discussed. The cost-benefits of the pilot tunnel are examined in view of estimated main tunnel costs.

Jan 1, 1987

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

By Kenneth F. Wyman

The following report details the successful construction of Contract 2A of the Three Rivers Water Quality Management Program, Intrenchment Creek Combined Sewer Overflow Conveyance System, in DeKalb County for the City of Atlanta, Georgia. The contract required construction of approximately 2878 m (9443 ft) of tunnel bored to an initial diameter of 7.95 m (26 ft 1 in), with provisions to concrete line those portions designated by the engineer to a finished internal diameter of 6.91 m (22 ft 8 in). Flanking the tunnel are two shafts. The upstream shaft was excavated to a nominal diameter of 4.87 m (16 ft) to accommodate a finished internal diameter of 3.66 m (12 ft). This shaft required a transition boot fully concrete lined to final dimensions of 6.91 m (22 ft 8 in) wide, 13.72 m (45 ft) long, and varying in height from 6.91 m (22 ft 8 in) to 12.80 m (42 ft). Associated work necessary to complete the contractual obligations included installation of 22.86 m (75 ft) of cut-and-cover box culvert, 484 m (1589 ft) of open-cut sewer installation in sizes ranging from 0.30 m (12 in) to 1.68 m (5 ft 6 in), one river crossing, 137.46 m (451 ft) of monolithic concrete trapezoidal channel, and installation of 19125 cu m (25000 cu yd) of select fill material compacted and graded to finished contours. The downstream shaft was excavated to a minimum diameter of 12.04 m (39 ft 6 in) and concrete lined to a finished internal diameter of 10.67 m (35 ft). Requirements here included installation of a complete pumping station with all mechanical, electrical, and structural elements necessary for dewatering the tunnel through the controlled use of four 250 hp submersible pumps discharging into the facilities of the Intrenchment Creek Water Pollution Plant. The objective of this project was to collect combined storm runoff and sanitary flows currently coursing through Intrenchment Creek

Jan 1, 1985

By Dermot M. Winters, Brent T. Wahlquist, C. Y. Chen

The enactment of the Surface Mining Control and Reclamation Act (SMCRA) in August 1977 addressed subsidence resulting from underground mines, in addition to creating the requirements for reclamation of surface coal mines. Subsidence control regulations pursuant to SMCRA were initially promulgated in March 1979. Several revisions have since been made. In addition, due to court challenges some regulations have been remanded and others are still on appeal. In the meantime the Secretary has agreed to initiate rulemaking on some issues. It is yet to be determined how the prohibition of certain areas from surface coal mining operations under Section 522(e) of the Act applies to subsidence. This presentation discusses the status of the regulations and issues related to or affecting the subsidence regulations.

Jan 1, 1986

By M. G. Mudrey

Considerable potential for metallic mineral resources in the lower Proterozoic rock of the Lake Superior region exists (Mudrey and Kalliokoski, in press). Most of the identified resources occur within a 2.0- to 1.9-b.y.-old lithotectonic assemblage characterized by extensive sedimentary strata in the north and thick volcanic se- quences in the south, all deposited on a two-terrane, composite basement of Archean age (DeMattis, 1989). Since the late 1960s, measured resources of nearly 90 Mt (100 million st) of typical volcanogenic massive sulfide at eight localities in Wisconsin have been discovered. The largest of these, near Crandon, contains about 61 Mt (67 million st) of ore averaging 5.6% zinc, 1.1 % copper, and 0.5% lead. Although none of these properties are in production, estimates by Mudrey (1978) suggest that Wisconsin could become a major contributor of newly mined zinc and copper in the United States. These discoveries and uranium and gold discoveries in the Canadian Precambrian are what have led to in- creased metallic mineral exploration throughout the northern half of Wisconsin (Fig. 1). In this chapter, we discuss the geology and legal framework in which the Proterozoic volcanogenic massive sulfide deposits were found. Exploration activities for other metals have generally been negative, and have been background noise for the legislative activities related to the massive sulfide discoveries. Uranium exploration has been consistently negative, although several different environments have been assessed. Other metal discoveries. such as titanium/vanadium, have been subeconomic.

Jan 1, 1991

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006

By R. McCulloch

Exploration activity in metallic minerals continued to decline in Montana in 1992 as companies either reduced budgets or left the state. The number of active projects dropped another 50% from 1991. Expenditures were 3% to 6% of 1989's 28.6 million. Many of the major mining companies closed offices in Montana. Although depressed commodity prices have hurried the exodus, continuous changes in environmental regulations, as well as the Mining Law of 1872, without regard to economic effect have had the most serious impact. Many companies indicate that Third World countries present a more stable business environment than the United States. Grassroots projects are nearly non-existent, while late-stage programs continue cautiously. Exploration activity continued at the following projects: Garnet, Pegasus Gold; Southern Cross, Asarco; Elkhorn, Goldfields; 7-Up-Pete, Phelps Dodge and Canyon Resources; Miller Mountain, Pegasus Gold; Sheep Creek, Cominco American Resources; Checkerboard, Kennecott and BHP Utah International; Emigrant Creek, Pegasus Gold; and Crevise, American Copper and Nickel. All mineral activity, whether on private, state or federal land, is regulated by the Montana Department of State Lands under three classes of permits - Small Miner Exclusion Statements (SMES), Exploration Licenses and Operating Permits. A total of 230 Exploration Licenses are active in the state with 26 of those being new. However, there are only 433 projects current in Montana, with many of those in the reclaiming stage. The majority of exploration projects consist of individuals expending time rather than money on properties. The number of mines functioning under operating plans declined by one when W.R. Grace closed its Zonolite operation.

Jan 1, 1993

By J. Hebert, J. Donnelli, J. Sedey

Installation of a Load Commutated Inverter (LCI) provides an economical method for conversion of a Fixed Speed Semi-Autogenous Grinding Mill into one with variable speed, qualities. Though capital intensive, the conversion appears to be one of the most cost-effective methods to gain the advantage of critical speed variations for variable ore characteristics. Expected advantages from the installation of LCI drives at the Goldstrike Mine were decreased liner wear, decreased media consumption and additional grind for increased production rates. These issues as well as construction, economics and performance will be discussed in the presentation. The utilization of the existing equipment came to play an integral part of the study and economic justification of the overall project.

Jan 1, 1999

By D. Royston

Gold ores containing antimony suffer from poor recoveries of gold in cyanidation due to the impact of antimony on the cyanidation process. Techniques such as lowering the pH for cyanidation can improve gold recovery, nevertheless a limit can be reached where high cyanide consumption makes traditional processing uneconomic. The paper outlines a process for the pre-treatment of gold-antimony concentrates to remove the antimony resulting in a low-antimony content gold-bearing residue suitable for efficient treatment for gold recovery through cyanidation. This hydrometallurgical process produces a by-product credit of commercial grade antimony trioxide as Senarmontite that can significantly offset the cost of the pre-treatment.

Jan 1, 2007

By John W. Shield

Oxide gold reserves are being rapidly depleted, especially in regions with long histories of gold mining, such as the Black Hills of South Dakota. However, these districts often have substantial additional deposits, where gold is refractory. It is not amenable to traditional cyanide extraction due to the presence of sulfide minerals that encapsulate or otherwise preclude the economic extraction of the gold. Several technologies have been developed to render refractory sulfide deposits amenable to traditional cyanide processing. These include roasting and pressure autoclaving. Unfortunately, these oxidation processes require substantial capital investment and incur significant operating costs. Microorganisms that obtain energy for their life processes by the oxidation of iron sulfides can be used to treat gold-bearing refractory sulfide minerals. As the bacteria convert the sulfide to sulfate, they expose any gold associated with the sulfide matrix. This makes the gold amenable to cyanide extraction.

Jan 1, 1996

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977