Search Documents

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By G. E. d’Aquin

Sources of sulfur have varied based on technology and societal needs. It has been mined in its elemental form for centuries. Twentieth century technology brought thermal mining (Frasch, 1894) to the forefront of sulfur extraction. Then, by the 1980s, petroleum processing generated almost 40 percent of the 50 Mt (55million st) of sulfur in all forms (SAF) produced in the world. Metals processing (the reclamation of effluent gas by various means as “sulfur in other forms,” or SOF) followed at 30 percent of all sulfur values produced and then Frasch at 22 percent. Petroleum and gas processing now generate most of the elemental sulfur produced in the world. Single Two Frasch mines remain, one each in Iraq and Poland. Conventional mining of small to insignificant volumes also survives in Russia, Latin America and Indonesia. The volume of “recovered” sulfur (the name commonly given by the industry to hydrocarbon-derived material) generated will increase faster than energy consumption as oil and gas with greater amounts of sulfur are used and environmental restrictions on the sulfur content of the fuel consumed become more stringent.

Jan 1, 2005

By Gordon Kidd

Inflation and burgeoning costs are two among many factors which have generated a new surge of interest in "fringe benefits" (sometimes referred to as "supplementary remuneration" or "supplementary compensation"). Other specialized forms of compensation ("perks", in the vernacular) such as company cars, windowed offices, etc., which also are the subjects of current study, are outside the scope of this paper. For businesses, interest in fringe benefits is based on concern for employees? welfare, compliance with government requirements, and an increasingly burdensome impact on bottom lines. In 1980, according to Fred D. Lindsey in the October 1980 issue of Nation's Business, employee benefits will cost American employers an estimated $420 billion. To paraphrase Winston Churchill, "some fringes!" Indeed, few if any administrators consider employee benefits as fringes. Employee benefits impact other major areas of a company's operations as well. As listed by Beadle (1980), these areas include employee relations, collective bargaining, short-term costs, long-range funding, manpower planning, compliance with legislation, taxation for the company and for the employee, corporate image in the community, competitiveness for staff, communications, administration, claims cost containment, etc., etc.

Jan 1, 1980

By M. Zhang, M. Menabde, R. Middleton

Whilst mine planners almost universally assume deterministic forward commodity prices when undertaking valuations of mining projects, historical data well demonstrates that those prices are quite volatile. This paper seeks to understand and quantify how this forward price uncertainty will impact mining project valuation. This paper will also present a way of computing an upper bound on the expected Net Present Value (NPV) of a mining project given forward commodity price uncertainty.

Jan 1, 2007

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997

By S. Chander, S. W. Musselman

The molecular structure of hydrophobic and hydrophilic groups in nonionic surfactants has been related to the wetting and dispersion of selected pigments. The nonionic surfactants included in this study are acetylenic diol based surfactants and ethoxylated alkyl phenols. The Langmuir model could be used to fit adsorption data. Further analysis of the data showed that the free energy of adsorption was a function of adsorption density of the surfactants at the interface. The change in free energy with adsorption density could be interpreted by considering a change in the orientation of the adsorbed molecules. Acetylenic diol based surfatants were found to have an area per molecule of 2-3 times that of similarly ethoxylated alkyl phenols. The wetting and dispersion properties of lamp black, a model hydrophobic surface, by these surfactants were investigated by contact angle measurements and particle size analysis. Acetylenic diol based surfactants with ethylene oxide contents between3.5 and 10 moles per molecule and alkyl phenol based surfactants with approximately 9 moles of ethylene oxide per molecule were found to provide superior wetting abilities. Longer ethylene oxide chains were required for superior dispersion capabilities within each family of surfactants. Complete wetting and dispersion was found to occur above the critical micelle concentration of the surfactants.

Jan 1, 2000

By Ben Sosewitz

The subject of rapid excavation tunneling is one that is extremely important to the people in the Metropolitan area of Chicago. My personal observation is that it is also extremely important to the urban communities around the U.S., to many local and state governments, and to the public officials who are deeply concerned about state affairs and taxes. The Metropolitan Chicago area is in fact, (as are 40 other major urban areas in the U.S.) confronted at the present time with a very serious combined sewer overflow, drainage and pollution problem which accounts for an estimated 40% of the pollutional load on its waterway system. In response to this the District has to date spent some seven millions of dollars in an attempt to find the most economical solution available for the elimination of this problem. This study included extensive investigations of the geological strata, the quantity and quality of storm runoff to be dealt with, and the various methods of storage and treatment available. It has considered solving the overflow problem by a concept involving a series of tunnels, rock tunnels, shafts and storage areas which will collect, retain and subsequently treat that portion of the combined sewer overflow which can be handled in the most cost-effective and economical way, consistent with following the federal and state standards - with which we at the present time agree in principle.

Jan 1, 1997

By Marvin V. Damm, Lloyd C. Venburg, Dan Sokol

Analytical and computer models are used to evaluate information obtained from existing data and investigation programs so mine water control systems can be designed and developed. These models allow the geohydrologist to predict the amount of groundwater inflow and the impact of dewatering and stream diversion on the hydrologic regime, and to determine the schedule and equipment needed for mine dewatering. This article describes uses of the model and the essential components necessary to construct an effective and practical one. Hydrologic models are constructed to determine the extent that mining activities will affect the ground water and surface water hydrologic regime. These models range from basic analytical, mathematical models to the more sophisticated finite difference and finite element groundwater models. Many factors determine the degree of sophistication, including the mining stage, the complexity of the hydrologic regime, the mining process, and regulatory requirements. Model Uses The geohydrologist and engineer construct models so the entire ground and surface water handling and supply system can be integrated and optimized. These models can provide the following data: • Information for water balance studies-the entire hydrologic regime for the area, including precipitation, transpiration, evaporation, infiltration, runoff, and the effect of geologic features. • Data on seepage rates during mining. • Information to design the depressurization and dewatering system, including water well spacing, location of sumping systems, need for grout curtains, and possible horizontal drain and underdrain locations. • Data needed to schedule dewatering and mining operations. • Prediction of initial and long-term impacts of mining and dewatering, including local and areal drawdowns, effects on existing wells, and modifications to the surface-subsurface hydrologic regime. Potentiometric surface maps and hydrographs can be prepared from these data. • Prediction of the effect of discharge from the water control system on the surface hydrology and data input to design systems for water discharge, storage, recharge, or reinjection. The results of a computer study that illustrates the effect of dewatering and reinjection into an aquifer to confine the cone of depression are shown on the accompanying figure. • Information to forecast potentiometric surface recovery after mining ceases. The accompanying figure shows the pumping and reinjection rates in a program that is adequate to dewater a mine and permit the recovery of potentiometric levels to approximate premining levels after mining ceases. • Documentation and design information for monitoring systems to be installed during all mining phases. • Water quality predictions and geochemical changes, including the possibility of brackish or saline water intrusion because of extensive dewatering or depressurization operations. • Documentation and data for acquiring permits from regulatory agencies. Model Input Program For any model to be effective, detailed hydrologic and geologic data must be gathered from a review of existing information and from an investigative program. These data should cover entire model limits. Data updating, revising, and refining should occur as new information is received from the investigation and monitoring programs, and from the mining operation as it progresses through the pre-mining, mining, post-mining, and reclamation

Jan 8, 1982

By I. S. Parrish

One of the most common errors uncovered while performing a reserve, or resource, audit is not in the geological modeling or grade problems due to poor sampling, prepartion or assaying. The error most commonly found is in tonnage or, more specifically, in the tonnage factor - that factor applied to volume to derive tonnage. Tonnage factors In the metric system, the tonnage factor is the density, or specific gravity. Specific gravity (Sp.g.) is defined by Dana (1947): • "The specific gravity of a mineral is the ratio of its density to that of water at 4° C (39.2° F). • "Density is the mass of the unit volume or weight of the body divided by the weight of an equal volume of water." When Sp.g. is multiplied by the metric volume it yields metric tonnes. In the English system, the tonnage factor is usually expressed in cubic feet per short ton (cu ft/st). When the volume in cubic feet is divided by cu ft/st, the resulting figure is in English short tons. Table 1 gives the cu ft/st factors equivalent to specific gravities from 1.6 Sp.g. to 5.8 Sp.g. The table is based on the following equation: cu ft/st = 0.9072 divided by Sp.g. times 0.02832 The blase attitude that most geologists have toward tonnage factors is echoed in the prevailing definitions of Reserves and Ore, as provided by the US Securities and Exchange Commission (S.C Form S-18), Canadian National Policy 2A and the SME Proposal for Reporting Terminology (SME February 1991). In each case, it is stated that "quantity" (SEC, SME), or "tonnage" (Can.2A), "is computed from dimensions revealed in...." etc. Unfortunately, "dimensions" do not directly yield tonnage. Dimensions must be factored by density to derive tonnage.

Jan 1, 1993

By Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity', innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1984

By Russell Barr

Strategic alignment throughout a mining organization is critical to effective strategic execution and good business performance. The alignment of strategic goals and objectives in the different operations and functions in a large global operation is a challenge facing executive management in light of legacy organizational structure and processes. An additional confounding factor in strategic alignment of acquisition and new project expansion is that mining projects and operations are frequently multi-cultural in terms of country origin as well as organizational culture. This brings together many cultures to accomplish the project or complete an acquisition (Financial Times, 2006). The mining industry presents numerous challenges to executives and mine management by the nature of the operation and organizational processes used in running it. For example, there seems to be an inherent conflict between the individual goals of the components that constitute a mineral processing operation (the mine, the mill, the smelter and the refinery), and lowest cost production of the final product. Managers of these component operations have specific objectives passed down from the corporate executives. Those site managers tend to be compensated based on throughput and perform to this main metric. This tendency to maximize throughput for an individual operation can contradict the general process flow of a best-fit solution to producing the final product at the lowest cost. In an effort to become more aligned, firms are increasingly using balanced scorecard derivatives at great cost and effort (whether internally or externally sourced) in an attempt to help with strategic alignment. Balanced score-cards have been effective in providing a good strategic scorecard to companies with some measure of strategic alignment. Many firms make this effort of using balanced scorecards. However, most firms are not strategically aligned or, at best, are sub-optimized, in terms of strategic alignment (Kaplan and Norton, 2006). The tendency in mining operations is to focus on operating individual components as optimally as possible and stretching existing assets to the best possible production rates. ?Making tons? is the common operational focus. Numerous factors underpin this focus and can affect the ability of the operation?s ability to align properly with the corporate strategy and strategic goals. Critical factors are legacy organizational structure, culture, processes and performance measurement systems. Changing anyone of these factors to affect better strategic alignment requires significant attention to managing change.

Jan 1, 2008

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By J. D. Bliss

The discovery that triggered the current gold rush in southeastern Peru was made in about 1975 along the Rio Madre de Dios in Madre de Dios Department (Fig. 1). About 5000 to 10,000 miners (called chichiqueros) were working in the area as of 1990. Placer mining is the principal source of revenue for people living along the Rio Inambari and west of Puerto Maldonado. As in past gold rushes, working and living condition are harsh. Supplies are expensive, and the area has poor access compared with other areas in Peru. Food, fuel and all mining supplies are trucked over dirt roads from Cuzco, a three-to-five-day trip (Fig. 1). Some material also comes from Brazil. Many placers have a similar life cycle, beginning with small-volume mining (surface or underground). At the end of this small-scale mining, the placer is exhausted or it has a sufficient volume of gravel high enough in gold grade to be worked by large-volume methods, which lead to exhaustion of the resource. The level of maturity of a placer can be determined from its gold grade. The amount of gold production from large-volume mining can be predicted, given detailed, cumulative gold-production data on placer deposits during small-scale mining (Bliss et al., 1987). Using this general model, the authors analyzed the placers in the Rio Madre de Dios area. Small-volume mining Most placer mining in the Rio Madre de Dios area is in alluvial deposits either in or bordering the major rivers. Locally, some placer mining is in terrace deposits above the rivers. All minerals (including the subsoil) in Peru belong to the state. However, a mining claim (denuncia) is easily obtained for mineral exploitation. It is separate from property ownership.

Jan 1, 1992

By D. R. Zuchelli

In order for MSHA to require the use of a noise control, the control must be proven ?technologically feasible?. Technologically feasible controls must reduce a miner?s noise overexposure to the permissible exposure level (PEL) or achieve at least a 3 dBA reduction in the miner?s noise exposure. The miner?s total noise exposure should be examined from an occupational viewpoint and not solely on a machine or equipment basis. This examination requires a field evaluation of the occupation as opposed to an equipment test conducted in a laboratory. The operator of a Hilti TE MD20 LS electro-pneumatic drill realized a full shift noise exposure (TWA8) reduction exceeding 8 dBA as compared to when operating a Gardner Denver S83F pneumatic jackleg drill while installing an equal number of drill holes into the Idaho Springs Gneiss rock formation. However, the Hilti drill?s penetration rate was only 27% of that of the jackleg drill. Although the Hilti drill was proven to be technologically feasible as a noise control, its slower penetration rate would require its economic feasibility to be evaluated on a case-by-case basis.

Jan 1, 2011

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981