Search Documents

By Ann M. Gosier

Over the past 20 years, diesel-powered equipment has been introduced into the underground mining environment in increasing numbers. While the introduction began years earlier in the metal-nonmetal sector, the exponential growth in coal mining use during this time has been more pronounced. Reasons for the continued use and rapid growth of diesel equipment in underground mines are easily understood. The safety and operational advantages afforded by this equipment in production and support systems are demonstrable. As other mine operators witness the advantages enjoyed by their competitors, they too move to introduce an increasingly diverse array of such equipment into their underground mines. As with any industrial technology, the use of diesel-powered equipment entails potential safety and health concerns. Existing Mine Safety and Health Administration (MSHA)approval regulations (30 CFR Parts 31, 32 and 36) apply only to diesel locomotives and mobile diesel-powered equipment for noncoal mines. In the absence of specific regulations, MSHA has required the use of equipment approved under Part 36 (gassy noncoal mines) for areas of underground coal mines where permissible electrical equipment is required. However, a considerable amount of diesel-powered equipment without explosion-proof or fire prevention features is in use in areas of coal mines where permissible electrical equipment is not required. It is on the use of this latter class of equipment that MSHA is focusing much of its regulatory attention relative to coal. The agency also is focused on revising existing occupational exposure limits for gaseous emissions and instituting limits on diesel particulate emissions for both coal and metal-nonmetal mines.

Jan 1, 1993

By Frank H. Blair

A study of paleogeography and paleo-environment, coupled with modern geochemical techniques and geologic inference, points to the presence of unconventional platinum group metal deposits in domestic and foreign ultrabasic terranes. During the laterisation of the tectonized and serpentinized mafic and ultramafic rock units, onshore winds provided abundant low temperature chloride to the laterite-saprolite profile. Here, an environment formed where gold, silver and platinum was dissolved, transported and redeposited. Changes in climatic conditions have helped preserve the redeposited metals in fossil laterites. The definition of "unconventional mineral resources" used here is taken from the Cameron Volume of Unconventional Mineral Deposits published by SME-AIME in 1983: "Unconventional mineral resources represent materials of possible economic importance that occur in geological or physical environments that have not been successfully exploited for the particular mineral." (van Rensburg, 1983). Chromite-rich rocks worldwide contain high platinum group metal concentrations. This feature is found in ophiolitic sequences, Alaskan-type ultrabasic complexes or statiform intrusions. Association of platinum group metals with chromite has received much attention. The reason for that associa¬tion, however, is not clear. Much has been written about how and where the platinum group metals occur. It is known that they are present in the spinel lattice, as solid solution elements in sulfides and as discrete platinum group minerals. This article outlines the reasons geologists should be looking at lateritic terranes to determine the feasibility of searching for undiscovered, low-grade platinum group metals amenable to openpit, bulk mining. Laterite-saprolite horizons could contain significant platinum group metals and location of anomalous values on the surface and in the weathered profile can lead to discovery.

Jan 1, 1993

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By David E. Thompson, Daniel J. Dobbels

INTRODUCTION The planning process for projects requiring construction of tunnels in urban environments can be highly complex and involves interaction with professionals of many disciplines. Typically the initial step in the planning process is to establish basic design criteria for the tunnel or tunnel system consistent with its intended purpose. Such criteria might include acceptable tunnel geometry, minimum and maximum slope or other associated criteria. Ideally, once the basic criteria have been established, the next step in the process might include establishing technically feasible horizontal and vertical alignment and shaft siting alternatives and developing "ball park" construction and operational cost estimates for the alternatives. Comparisons can then be made regarding the relative technical and economic merits of the alternatives and the most favorable alignment(s) are selected for further study or preliminary design. Typically the last and perhaps the most important task that is conducted during the planning stage includes identifying issues and potential problems to be addressed during the design and construction stages of the project. Many issues warrant consideration during the planning phase of a tunneling project. For the purposes of this paper, these issues can be divided into two broad categories: technical and non-technical. Important technical issues include, among others, general design criteria, geotechnical and geoenvironmental issues, and constructibility issues. Important non-technical issues include, among others, right-of-way and easement related considerations, project scheduling constraints, both short and long term environmental impacts and overall cost/benefit aspects of the project. With respect to influence on the planning process, these two groups of issues often cannot be separated completely. For urban tunneling projects, however, it is most often the case that the non-technical

Jan 1, 1991

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"In recent years, much has been said and written on Lake Superior ores, giving the impression that the quality of the ore is deteriorating in grade and that the reserve of high grade ore is rapidly being depleted. Average analyses of ore produced in this district since 1902 show that the average quality has been practically uniform since 1910, and now closely approximates the average for the total reserves of merchantable ore.The accompanying tables and charts show the average analyses for the past ten years, weighted according to tonnage: The chart above shows graphically the average natural iron content for the old range, Mesabi, and grand total Lake Superior ore shipments since 1902.During the last ten years the decrease in iron content for shipments from all ranges except the Menominee was only' .05 of 1 per cent, while for the Menominee ores there was an increase of .052 of 1 per cent. These tabulations and the chart prove that the average quality of the total annual production of iron ore from the Lake Superior district is uniform. Mining men of the district know that all of the merchantable ores of every ore body are being mined out cleanly, and therefore the present average iron ore content of total annual shipments from the district may be expected to continue as long as the present merchantable ore reserves last. There is no logical reason to expect a decrease in the average iron content. Furnaces require ore of definite quality, and if this quality of ore cannot be produced from the natural ore bodies, it must be produced by mechanical means—that is, by concentration of low grade ores or iron formation."

Jan 1, 1920

By G. Brofas

Mt Giona situated in the floristic hot-spot of southern-central Greece has an especially rich flora that counts more than 1000 native vascular plant taxa (species and subspecies) and an important plant endemism that is estimated to be about 10% of the native flora. The danger of population reduction of rare and endemic plant species and the opportunity to use rare native species in rehabilitation projects are two different aspects of rehabilitation planning in Mt Giona. In this study, an inventory of rare and endemic species of the area, their classification into IUCN threatened categories and an estimation of their habitats vulnerability are provided. The results emphasize the necessity to develop a monitoring program to analyze population viability of certain threatened plant species. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed. An inventory of the species that have colonized the mining spoils was also undertaken. Twelve of them are endemics. Seven native species, because of their biological and ecological features, were selected for rehabilitation purposes of disturbed areas by mining activities. Seed germination, aspects of their reproductive biology and seedling emergence after sowing in pots under field conditions were studied. The seed germination study in the laboratory led to the identification of the optimum germination conditions and the creation of germination protocol for each species. Seedling emergence depends on the sowing season and the mulching. The use of the above species is recommended for rehabilitation purposes. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed.

Jan 1, 2007

By J. G. Dunn, A. S. Ibrado, D. J. Hollbach

Gold production is one the most important mineral process­ing industries in Western Australia. The gold is usually found in either weathered oxidised zones, or associated with sulfides. In the latter case, oxidation is achieved by some form of chemical processing, such as roasting or more recently bacterial leaching. In all cases, gold is dissolved out of the oxidised matrix by cyanide solution. Pyrrhotite is an iron sulfide generally represented by the formula Fe1_,S where O x 0.125. Three different structural forms ofpyrrhotite are known to occur naturally, stoichiometric FeS (troilite), hexagonal pyrrhotite Fe1_xS and monoclinic pyrrhotite Fe7S8 [I]. Substitution of iron atoms within the pyrrhotite structure by other ions of similar atomic radius such as nickel, copper, cobalt and manganese is also possible [2], and often observed in natural pyrrhotite samples. Pyrrhotite is abundant in Western Australian sulfide mineral deposits which are commonly associated with gold bearing ores. It is generally believed that pyrrhotite has a detrimental effect on gold recovery from such ores, as it is commonly claimed to decompose in alkaline, aerated cyanide solutions to form iron cyanide complexes, thus consuming free cyanide, and to form sulfur/oxygen containing species such as sulfate, through oxidation of sulfur in pyrrhotite, which thus consumes oxygen. From information gleaned from the literature, claims about the high reactivity of pyrrhotite in cyanide appear to be based on early cyanidation studies performed on gold ore samples which have been poorly characterised, and contained impurities such as pyrite, arsenopyrite and chalcopyrite, which may have also contributed to the levels of species observed in solution [3-5]. In addition, the investigations do not take into account that iron atoms in the pyrrhotite structure may have been partially substituted by other atoms that influence the solubility of pyrrhotite in cyanide solution.

Jan 1, 1995

By Hans Ehdwall, Erling Strandon, Friedrich Steinhäusler, Victor A. Leach

INTRODUCTION The basis for any measures in radiation protection is the quantitative assessment of the radiation exposure. Due to the extensive requirement in health physics manpower and related cost it is necessary to develop certain criteria regarding the necessity of monitoring and the selection of population groups to be monitored. Depending on the overall objective of the particular programme, the specific requirements for the measurement of atmospheric levels of radon, thoron and their daughters for practical radiation protection purposes differ significantly for those in the case of research applications, such as use of data for epidemiological studies. As part of the OECD-NEA Programme on Radon Dosimetry and Monitoring Task Group 1 reviewed available models for lung dosimetry in the case of inhalation of radon 222, radon 220 and their daughters (James et al., 1981). Using defined reference atmospheres for underground- and open-pit mining conditions as well as for dwellings, normalized conversion factors were calculated for the mean bronchial dose (mGy) per Working Level Month exposure (WLM). Task Group 2 discussed the features and adequacy of the Working Level (WL)-concept as a physical correlative of the absorbed lung dose and its limits of confidence and accuracy (Johnson and Leach, 1981). The WL-concept was found acceptable for radiation protection purposes provided that modifying factors like particle size, unattached fraction and respiratory minute volume did not cause the effective dose equivalent per WLM as calculated by either the James-Birchall or Jacobi-Eisfeld lung models to be more than 50 % above that given by ICRP of 0.01 Sv/WLM. For application in epidemiological studies the WLconcept is considered acceptable if the calculated absorbed dose to the tissue does not vary by more than 50 % (at the 95 % confidence level) from that given for defined reference conditions. In the following, objectives and requirements for the measurement of radon, thoron and their daughters are discussed for operational health physics routine and special research applications according to the scheme outlined in Fig. 1.

Jan 1, 1981

By Qiong Wu, Li Guo, Qinghua Gu

BP neural network is a multilayer feedforward network trained by error back-propagation algorithm, which is one of the most widely used neural network models. However, BP neural network has exposed more and more shortcomings and deficiencies with the expansion of the application scope. In the prediction of ore quantity, BP neural network has the characteristics of slow convergence and easy to fall into local minimum point. In order to obtain the global optimal solution, and to improve the defects of BP neural network, this paper proposes combination optimization algorithm of genetic algorithm (GA) and BP neural network to improve the speed and accuracy of forecasting the main design flow chart and the analysis of the sort distinguish algorithm are offered, and then some problem in the design and debugging of the algorithm are discussed. On this basis, the GA-BP neural network model is constructed and applied to optimize the initial weights and threshold value of BP neural network. This model choices the floating point coding method to encode the connection weights and thresholds, and divides subjects into several populations. Through the introduction of selection, mutation, crossover, initial weight and other operators, making operational synergies between the various groups. This study selects 30 geological units, 8 quantitative variables (Pb, Zn, Cu, Mo, Si, Ni, Co, V) and 12 qualitative variables to carry out empirical analysis. Then the simulation of the algorithm is carried out in MATLAB and the parameters are analysed. By normalizing the input samples, 22 groups of observation data are used as the training data for prediction, and the latter 8 groups of observation data are used as the test data to be verified. The results show that when the ore quantity characteristics are not very significant, the model will produce prediction bias. But the improvement of the algorithm increases the efficiency of the function approach capacity of BP neural network and conquer the BP neural network system’s instability. It provides an auxiliary guide for ore prediction, which have higher reference value.

Jan 1, 2017

By Rebecca A. Miller, Terry M. Hertel

In-pit identification of neutral waste rock at the Zortman and Landusky minesites in Montana, by visual and chemical analy­ses, will assist in proper segregation and placement of rock so that soil and water resources can be protected. The use of too few or very general segregation criteria to identify neutral waste rock can result in ineffective waste rock segregation. Conversely, the use of overly restrictive criteria can result in the unnecessary loss of valuable reclamation material that would otherwise have to be mined elsewhere and hauled to the site. Recognition of nonre­active materials can be accomplished on a site specific basis with the use of visual observation and simple chemical analyses. The choice of chemical parameters used to analyze rock samples is constrained by the length of time needed to conduct the test. These analyses must require no more than 24 hours to complete so mining can proceed without delay. Limits set for the chosen parameters must be reasonable and defensible. To achieve these objectives over one thousand samples were collected at the Zortman and Landusky minesites and clas­sified by rock type, total sulfur content, paste pH, and net neu­tralizing potential (NNP). In addition, over 22 humidity cell kinetic tests were conducted to help corroborate static results for waste rock. Another 8 humidity cells were configured in series to test waste rock blending and waste rock/limestone capping alternatives as mitigation for acid rock drainage. Leachates were analyzed for pH, conductivity, alkalinity, acidity, sulfate, Al, Cd, Cu, Fe, Mn, Zn, Mg, and Cr in some cases. Petrographic analysis, as well as total sulfur content, paste pH, and static and kinetic test results identified three geochem­ically different waste rock groups: 1) Archean amphibolite gneiss and Paleozoic carbonates and shales, 2) Tertiary syenite porphyry, and 3) other less abundant Tertiary igneous and Archean metamorphic rocks.

Jan 1, 1996

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By Jock McGregor, Deepak Malhotra, Leonard Harris

After more than 100 years, alkaline cyanide leaching of gold and silver ores, either directly in the case of oxidized ores, or after pretreatment of refractory ores by roasting, pres­sure leaching or bacterial leaching, remains the dominant r leaching method to extract the precious metals f om ores. Leaching with halides (chlorine, bromine and iodine) and with thiourea and thiosulfates is less common but prac­ticed in some cases to dissolve the precious metals both from ores and jewelry and electronic scrap. Cyanide solutions can contain from 1 ppm Au to 30,000 ppm Au. According to the source, i.e., agitated tank leach­ing, heap leaching, eluates from stripping activated carbon or waste electroplating solutions. Similar variations occur with silver which can have a profound influence on the recovery method. The presence of other elements in the leach solu­tions, particularly mercury and copper, likewise play an important role in the procedures required to recover the gold r and silver values f om solution. The same circumstances are found when lixivants other than cyanide are used to dissolve the precious metals. For decades, the preferred method of recovering gold and silver values from alkaline cyanide leach solutions was by zinc dust precipitation according to the Merrill Crowe process developed in the late 19th century. Finely ground gold and silver ores or concentrates were either leached directly or after roasting, in agitated tanks or Pachucas and subjected to solid/liquid separation by filtering or by treat­ment in counter-current-decantation washing thickeners (CCD). This solid/liquid separation step was often very dif­ficult especially when ores containing high quantities of clay were treated which caused filtration or thickening problems. Following testing and development by the U.S. Bureau of Mines (USBM) in the late 60s, the introduction of carbon­in-leach (CIL) or carbon-in-pulp (CIP) plants to recover gold and silver from leach pulps was one of the greatest opera­tional and cost saving improvements made in the industry in South Dakota and quickly spread around the world to be the most common process to recover gold and silver from cyanide solutions.

Jan 1, 2000

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By Rafael C. Castro, Paul V. Savard, Kathleen M. Murtagh

Preliminary design is underway for the Massachusetts Water Resources Authority’s (MWRA) next major tunnel program, the Metropolitan Water Tunnel Program (MWTP). The MWTP is the latest part of MWRA’s ongoing efforts to achieve redundancy for its metropolitan water transmission system including its historic deep rock City Tunnel, City Tunnel Extension and Dorchester Tunnels. The MWTP comprises several deep rock tunnels that will be approximately 10-foot to 12-foot finished diameter totaling just over fourteen miles long and ten connections to existing large diameter surface piping and pumping stations. This paper will present an update on current engineering and permitting efforts, packaging schemes, and the schedule to complete the MWTP.

Jun 13, 2023

By M. Nichols

Where am I? Where are they? Where is it? These are the fundamental questions that need to be answered in managing people and resources. This paper explains how GPS positioning technologies answer those fundamental questions and provide better information management from initial exploration work through daily mine operations to reclamation work and environmental monitoring.

Jan 1, 1998

By D. L. Crouse

The worldwide talc industry has experienced significant changes since the 1980's. Consolidation of companies and operations in Europe, Australia, and North America has altered the face of supply and distribution. Imports of Chinese and Australian crude have increased competition and product options. The number of processing operations without local mines has moved competition closer to the market area. Quality controls related to ISO certification and tighter specifications demanded by the customers have altered the way our mines and mills operate. Ceramics, coatings, and paper applications continue to consume the majority of processed talc.

Jan 1, 1997

By Stephen V. Thompson

Within recent years portable seismic refraction units have found their place in the industry for shallow investigations, Completely portable, relatively inexpensive and of proven accuracy, the portable refraction seismograph is an electronic tool in an electronic age. The age of electronic instrumentation has seen the development of seismic reflection and refraction equipment for deep exploration, especially in the petroleum industry. Large, expensive units, normally truck-mounted and utilizing explosives, are being used successfully for this type of sub- surface investigation. The portable seismograph utilizes the same theory for shallow work as that applied to deep refraction seismology.

Jan 1, 1964

By Robert L. Stroup

Let me open my remarks this morning by stating how we as legislators and as natives of the western coal-producing states feel about our role in becoming one of the major producers of coal-related energy and chemical products is similar to the groom at his shotgun wedding. We are apprehensive, to say the least, as to the ultimate outcome. We do not have complete freedom of choice. It will certainly change our quality of life. We are concerned about the increase in population, but are realistic enough to recognize that we are forced to go through with the marriage. Other alternatives could be worse than the bride. Also, we were aware that this could occur, but we did not plan on it being this sudden. Or, put another way, we have two groups advising us that our choices are cattle or coal, food or fuel, pollution and people or pure air, wheat or gas, clean water or prosperity, noise or solitude.

Jan 1, 1976