Search Documents

By H. C. Juvkam-Weld

R. Michael Craig Mr. Juvkam-Wold's article is a timely and much needed presentation of the method of depressurization to reduce ground-water inflow into mine shafts. The article is very informative and discusses the effects of depressurization upon shaft inflows adequately. However, the article omits a discussion of another important benefit of depressurization: the reduction of potential for artesian burst or, as it is also called, floor heave. Confined aquifer systems (artesian aquifers) can contain water under several hunder pounds per square inch (psi) of pressure. For example, water levels at elevations of 455 m (1500 ft) or more above the top of the Westwater Canyon member of Reply by H.C. Juvkam-Wold In general, Mr. Craig's comments are useful and accurate regarding the potential benefits of aquifer depressurization. However, two of his points require further explanation since they may lead to a misunderstanding of my paper and its predictions. These refer to his comments regarding failure to account for storativity and to non-artesian conditions. Equation 5 is indeed Darcy's steady state equation. However, as a careful review of the appendix in this paper will reveal, I have used this equation to represent semi-steady state conditions. In other words, steady state conditions are assumed at any instant of time, but conditions may change gradually from

Jan 2, 1983

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By Serguei A. Diatchkov

The principles of classification of reserves and resources in the Soviet Union were developed in 1960. Mineral reserve calculations were reviewed by the State Committee on Reserves for approval, then registered in the State List of Mineral Deposits and included in the State Balance of the Reserves. In 1981, however, a new "System of Classification of Reserves and Resources of Mineral Deposits" was adopted. This classification system (Table 1) is still used today in the Commonwealth of Independent States (CIS). It subdivides mineral concentrations into seven categories in three major groups, based on the level of exploration performed: explored reserves (A, B, C,), evaluated reserves (C) and prognostic resources (P1, P2, P3). Explored reserves Explored reserves are calculated within exploration contours. Category A The A category is the highest level of classification for any given mineral deposit and requires comprehensive exploration. First, the ore body's position, shape and structure must be accurately delineated (Fig. 1). Next, the mineralogy of the ore body must be studied to determine its composition and properties as well as the distribution of both ore and detrimental components. It is also necessary to outline the blocks of barren rocks and limits of subeconomic ores and to distinguish between the different types, grades and physical-chemical properties (mineral texture and structure) of the ore, the

Jan 1, 1994

By Scott Lawson

BOB FALCONER: Our next topic leader is Scott Lawson. Scott is manager of human resources for Independence Mining Company, Cripple Creek and Victor Gold Mining Company, Victor, Colorado. Scott has 25 years of human resources management experience in the mining industry, surface and underground, precious and base metals. His topic this morning is "It's the Employee That Counts." SCOTT LAWSON: When reviewing the topic of productivity in a union versus nonunion workplace, we need to look at who, and not what, can make the difference in ensuring the success of a production-oriented operation. It's not explicitly whether the property is unionized or not, but whether the employee team (including the "management group") is working together to accomplish common, shared, and meaningful goals. The bottom line is what action or actions can be taken to develop trust and to strengthen working relationships that challenge and compel employees to willingly share their particular areas of expertise. I want to share a real-life experience that happened to me during the summer of 1961. Perhaps some of you will be able to relate to the following story. I was an 18-year-old fresh out of high school, ready for my first true work adventure. I found summer employment for myself and two friends with the New York Central Railroad in Cleveland, Ohio. Our jobs were as laborers, laying ties and rails, and unloading ballast. We made $2.62 an hour. We were fat cats! My friends and I took on the job with a great deal of vigor, to the dismay of our fellow workers. These workers were unionized by the Railway Workers, which I believe were affiliated with the Teamsters. Talk about being naive, we wrote the book in 1961. When we took the jobs, we did not realize the employees were represented by a union, even though we didn't think they worked too hard. Within our first two weeks of work, we established new daily records for laying virtually twice as many ties as had been standard, and we nearly tripled production by the end of our hall of fame railroad careers. We even took naively to the next level by lining up the ties for our afternoon work shift during our lunch break. In 1961, we thought we were the Mantle, Maris, and Colavito of tie laying. For the younger set in the audience, we would have felt like the McGwire, Griffey Jr., and "The Big Hurt" Thomas of tie laying. A section of the union contract allowed for a 60-day probationary period during which the employee was evaluated and also exempt from joining the union. I will venture to say that, to none of your surprise, on day 60 we were asked to join the union, and on

Jan 1, 1998

By Jurgen H. L. Stuve, Rick E. M. Widelski

Any one who has been involved with the mining or the treatment of gold-bearing ores will agree that at the end of the total process, the quantity of gold recovered is never as much as was expected. These short falls are usually explained away by claiming that:- the original evaluation of the ore being mined was inaccurate the plant treatment process is not at its optimum theft is taking place excessive dilution occurs during mining The truth of the matter is that the gold is being "lost". During all the stages of its production, starting from the mining, right through to the smelting process, a certain amount of gold is not recovered. When a newly found gold deposit is being evaluated and the drilling data being analysed, cautionary factors are applied so that the grade is not over-stated. Once the decision has been taken to start mining and development is in progress, the exposed ore is sampled. When Again, when this data is being analysed more safety factors are used to ensure that when a piece of ground is given a block-value, the gold content is not over estimated. mining actually takes place and the ore transported to the plant for treatment, the metallurgical department also introduces certain safety factors when predicting how much gold will be recovered. This shows that the quantity of gold that one expects to finally recover is already a conservative figure. The actual quantity recovered invariably falls short of this figure, in fact, South African gold mines are satisfied when achieving a Mine Call Factor (MCF) of 85%. In the last few years a great deal of work has been carried out to investigate how this unaccounted for gold is lost and what steps can be taken to remedy the situation. Previously mined areas were re-swept using the traditional hand brush method; experiments were carried out with water jets sometimes in conjunction with compressed air and even small portable vacuum cleaners were tried. None of these methods were totally successful in recovering the left over gold but the use of vacuum systems showed the most potential. the In South Africa this has resulted in introduction of high-powered vacuum systems on the gold mines to suck-up this lost gold. These were initially introduced in the mining areas, particularly old areas, to recover any left over ore. The results proved extremely profitable, So much SO that presently, well over 120 suction systems are doing this type of work. This success encouraged plant operators to look at areas of potential loss in the plant itself. This has resulted in an increasing number of machines being supplied to gold plants mainly for clean-up applications with the bonus that the material sucked up invariably contains gold.

Jan 1, 1993

By Kim W. Wright

Introduction Mining operations require maps for each phase of project development. Engineering plans, cross-sections, and isometric drawings are also needed. Maps are used for geologic interpretation, reserve estimation, permitting, property acquisition, site studies, development work, and production. Maps and drawings are essential to mining. They provide needed information. Generating these products, however, requires many manhours. The filing and organization of maps and drawings is cumbersome, due to their size. Major map changes can necessitate the production of entirely new documents and, thus, additional manhours. The volume of maps and drawings generated in the life of a single project can be extensive. For example, some utility companies have data bases containing more than a million individual maps (one reported eight million). These problems were considered necessary evils in the past. Now, with the automation of map and drawing production, improvements can be realized. Computer-aided mapping and design offers a new approach for the production, management, and storage of drawings and maps. This approach promises benefits in time management, productivity, efficiency, and flexibility. In all economic projects, the bottom line is cost reduction. And implementing computer-based mapping and design techniques can lower costs and increase project profitability. AM/FM/CAD/CAM Automated Mapping/Facility Management (AM/FM) and Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) are becoming buzz words in the engineering world. Most relevant to mining are the concepts of AM and CAD. These terms relate to the application of computers, specifically computer graphic technology, to mapping and design. CAD refers primarily to the design of components and structures in two and three dimensions. But it can apply to the three dimensional modeling of mine workings, ore bodies, and geologic structures AM refers to the automation of conventional map production. AM/CAD systems use computers to store, manipulate, produce, and update drawings and maps in two and three dimensions. Ideally, the calculating capabilities of computers are also used in conjunction with design and drawing generation, offering capabilities not available with conventional, manual mapping and design processes. To better understand concepts associated with AM and CAD applications, the understanding of a few computer-related terms is necessary. Table 1 explains some of these terms. System Features The capabilities of AM/CAD systems are based on viewing transformations. These are the basic, manipulative tools by which AM/CAD packages generate visual representations of data. Examples include the rotation of a three-dimensional object through space, the expansion or contraction of maps to fit a given scale, enlargements of small areas on maps or drawings for detailed viewing, and the generation of cross-sections from three dimensional data. AM/CAD systems incorporate data base management in their architecture. This allows a user to modify, move, delete, or manipu-

Jan 6, 1985

By L. W. Laage

Throughout recorded history, underground fires have plagued mining operations. Compared with other hazardous situations in underground mining, a fire can become a global problem by swiftly spreading deadly carbon monoxide and other products of combustion (POC's) throughout the whole mine, often without warning. Experience has shown that when fires are detected and located in their early stages, they are much easier to control and proper escape routes can be more intelligently selected. Recent advances in sensor and data communication technology have made reliable mine fire .detection system installations possible. Unlike building construction. in a mine, it is impractical to install detectors at every desired location. Abandoned workings and unsafe locations preclude sensor installations from both safety and economic standpoints. The net effect is that some fires are detected and located early while the location of others, even if detected early, remains unknown too long for effective evacuation and fire fighting.

Jan 1, 1989

By A. Mukherjee

This paper presents an analytical technique for prediction of the damaged rock zone (DRZ) around a circular drift subjected to an anisotropic stress field (analytical solution exists only for the case of hydrostatic stress field). The method can readily be adapted to micro or personal computers. Stress concentrations around the drift are calculated at the centers of small rock elements, using the analytical solutions for a hole in an infinite plate. Potential failure of a rock element is assumed to be governed by the Coulomb failure criterion. When the failure condition is exceeded for an element, the excess shear stress is transferred to the neighboring elements. Progressive failure is allowed to occur until convergence is obtained. The final configuration of the damaged rock zone so obtained can be used to assess rock support requirements, as well as modified modulus and permeability of the DRZ.

Jan 1, 1988

By Terrence D. Chatwin, James Hendrix

Based on the findings within their report to Congress, the US Environmental Protection Agency (EPA) announced that it had decided not to regulate mining wastes under the hazardous waste regulatory program. However, they found that some mining wastes are hazardous and may be causing environmental damage. Cyanide wastes from heap leach operations were included in this group. In evaluating the effects of cyanide use in mining one finds a significant lack of information on the fate of cyanide in soils. Cyanide attenuation and degradation of soils is important, because ground water is a major potential pathway for cyanide contamination. There is a strong potential for cyanide to be removed from solutions as it migrates through soils· by volatilization, chemical reaction, adsorption, oxidation and biological processes, but no definitive investigation has defined these mechanisms adequately to be able to predict the fate of cyanide in soils.

Jan 1, 1998

By Jan M. Mutmansky

The application of computers and operations research to mine planning problems has changed and progressed significantly over the last several decades with a continuing growth and increased breadth of applications being quite evident. A scan of the volume associated with the 1969 APCOM published two decades ago (Weiss, 1969) indicates that the primary applications in mining were often in the areas of short-term and long-term planning and production scheduling. The applications at that time were oriented toward underground and surface mining, but block and other mine sequencing and scheduling problems for large open pit mines were perhaps the most popular target for the operations research approach. A variety of operations research techniques were used at that time with heuristic models, mathematical programming models and simulation programs all being commonplace. The computers used were usually mainframe models which were of ten shared by accounting, engineering, planning and research groups.

Jan 1, 1989

By Greg Blerie

The requirements placed on belt conveyors grow increasingly complicated No longer is it sufficient for the conveyors to merely move material from "Point A" to "Point B. " Now these systems must be able to produce a specified flow, guaranteeing a plant can operate as scheduled without peaks and valleys in material flow and production rate. In addition, the conveying system must provide effective control, to minimize the problems and costs associated with the escape of fugitive material these problems include unscheduled shutdowns, premature equipment failures, regulatory headaches, poor neighbor relations, and health and safety issues. The key to accomplishing these goals is the loading and discharge of the conveyor belts. Fortunately, new designs for the chutes that accomplish conveyor loading and discharge can move material efficiently, without blockages and while minimizing the amount of dust generated This innovation is the development of engineered flow chutes

Jan 1, 2004

By Deepak Malhotra, Sean Armstrong, Linda Baltich

The economic profitability of any mineral company is dependent upon maximizing mineral recoveries while minimizing costs. The effectiveness of any strategy to meet this objective is dependent upon firstly obtaining quantitative information concerning the steady-state metallurgical balance of the plant, and secondly, how efficiently this information is used to improve/optimize plant performance. This two-step approach can be designated as a "plant audit." Plant audits on a routine basis can be very expensive and time-consuming. Most plants have reduced staffs to cut costs. The remaining staff has to spend time to solve production/operation problems, thereby leaving limited resources (i.e., people, time, and money), for plant auditing. This paper briefly reviews plant auditing categories, and a systematic approach to auditing which has been successfully used at several operations. An example illustrating the use of this approach in gold operations is discussed in this paper.

Jan 1, 1992

By Silvia H. M. Grimaldi, Afonso H. Martins

The scope of this experimental work was to study the yttrium extraction and stripping behaviour in a solvent extraction system with mono(2-ethylhexyl)2-ethylhexylphosphonic acid (IONQUEST 801) in a chloride system The study was performed for only one contact between organic and aqueous phases The experiments were carried out according to a factorial design. Due to the statistical analysis and its experimental proof, the optimum conditions for maximum yttrium loading into the organic phase of the extraction stage were 16 minutes for time of contact between phases, 980 rpm of stirring intensity and pH=2.3 for the aqueous phase of the sovent extraction system. The optimized experimental conditions by the statistical approach for the stripping stage were: time of contact between phases equal to 20 minutes, 1050 rpm of stirring intensity and 1.75 M HCI into the stripping aqueous solution.

Jan 1, 1995

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By S. K. Kawatra, S. J. Ripke

During 1998, 62 million tons of iron ore pellets valued at $1.7 billion were shipped from U.S. mines. These pellets are the primary source for domestic iron and steel production. During pelletization, binders are required to improve the green strength of the pellets. Each year, bentonite binder costs a typical plant from $3 million to $5 million. Reducing the bentonite dosage has the advantages of significant cost savings while producing higher quality, lower silica pellets. The authors have recently identified a new and important bentonite binding mechanism, the fiber theory. During this study, procedures were developed that took advantage of the ability of bentonite to form fibers, and resulted in a dramatic decrease in the necessary bentonite dosage. Acceptable quality pellets were produced with the bentonite dosages reduced in half from 14 lb/lt (0.66%) to 7 lb/lt (0.33%).

Jan 1, 2001

By R. L. Murray-Smith, M. E. A. Robertson, M. J. Prosser

The AZTEC is an automated instrument, for the non-destructive analysis of gold ore samples, which uses energy dispersive X-ray fluorescence (XRF), This is achieved by X­ray tube excitation of gold K X-rays. The first production instrument was commissioned at Vaal Reefs Chemical Laboratory (VRCL) in November 1987, followed by two second generation instruments in 1989. AZTECs have also been installed at Western Deep Levels and at Anglo American Research Laboratories (AARL). A further unit is being assembled at Ashanti mine, Ghana. At VRCL the AZTECs are used primarily for the evaluation of mine (stope) samples. Each of the production instruments can routinely analyse 650-700 samples per day, with the aid of a robotic sample transfer system. Various techniques have been evaluated for increasing sample throughput. For example, higher value samples can be counted for a shorter time to obtain the necessary relative precision.

Jan 1, 1991

By Hugh K. Herbert, R. John Watling

Laser Ablation-Inductively Coupled Plasma-Mass Spectrom­etry (LA-ICP-MS) has been used successfully to "fingerprint" gold in forensic investigations within Australia and abroad. By comparison of the elemental associations it has been possible to relate gold to specific mineralising events, mines, bullion samples and fabricated articles. The methodology facilitates identification of the provenance of gold thereby providing definitive scientific evidence in criminal investigations. "Gold" samples for analysis span a wide range of materials with many requiring exhaustive prior separation and treatment to present the contained gold in a chemically "unmodified" state, and in a form, suitable for LA-ICP-MS fingerprinting. The quality of the fingerprint, and hence its value in evidence, is directly related to the rigours of prior sample preparation and evaluation, to an appreciation of the history of the gold under investigation, and to the skill of the analyst.

Jan 1, 1995

By P. Maraboutis

Extractive industry (mining and quarrying operations), as other industrial activities, is subject to environment protection laws, regulation and standards such as the Environmental Impact Assessment directive, Natura 2000, Habitats & Birds directive, Water Framework directive etc The European Commission (EC) is aim to strengthen the EU environmental legislation to improve the (environmental and human) safety of mining activities. The mineral processing and the management of the mining waste will be covered by the new amendment of the Seveso II Directive, by a Best Available Techniques reference document (BREF) describing the Best Available Techniques of mining waste management and a new directive on the mining waste management. At the same time initiatives as the environmental liability, the energy taxation for environmental reasons and the natural resources management policy, which will have a positive impact on the protection of the environment, will affect the extractive industry operation procedures.

Jan 1, 2002

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999