Search Documents

By Hemang Desai

A damaged outlet pipe beneath Lenihan Dam has restricted reservoir discharges, severely constraining the owner?s groundwater recharge program. The solution, a new outlet pipeline through the dam?s right abutment, includes an approximately12.2-m-deep (40-ft-deep) shaft and 618.7-m-long, 4.3-m-diameter (2,030-ft long, 14-ft-diameter) tunnel mined in Franciscan melange composed of hard blocks of rock and soft clayey matrix. Alternating road header with drill and blast operations and using steel ribs and shotcrete have proven a flexible combination for handling the variable ground conditions. Excavating the shaft and connecting it to the tunnel require lowering the reservoir for five months, during which time careful construction sequencing and use of a tunnel plug eliminate the risk of an uncontrolled discharge.

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By A. Iannacchione

Longwall mining began within the Pittsburgh coalbed of Pennsylvania (PA) in the early 1970?s. Originally, longwall mine layouts were designed to fit within existing room-and-pillar operations, where panels were limited to that of typical production panels, e.g. a few hundred feet wide by a few thousand feet long. In these early designs, the gate entries were comprised of chain pillars similar to those found along main entry systems or within pillar recovery sections. The modern longwall mine has little in common with their 1970?s predecessors. Today the entire mine layout is designed around the longwall mining method. The longwall panels have grown to well over one thousand feet in width with lengths now measured in miles. In addition, development pillar sizes and shapes are matched to specific performance requirements.

Feb 27, 2013

By G. E. S. Valadao, J. D. Miller, C. L. Lin

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake poremicro structure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 m, length of 500 m and height of 4000 m. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: 1) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method,2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4)some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel, and stone) creates environmental impacts. A systems analysis method has been designed to characterize the components of the environmental system, identify potential impacts to those systems, and evaluate the extent of those impacts. The step-wise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis, and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface, and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2001

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By B. R. Zernich

Advances in tunneling technology, such as Earth Pressure Balance and Slurry Shield methods, have allowed the tunneling industry to construct tunnels in increasingly difficult ground conditions. In recent years, a number of civil projects including large diameter train tunnels, subway tunnels, water tunnels, sewer tunnels, and combined sewer tunnels have been successfully completed deep beneath the water table in soft ground conditions utilizing modern day Tunnel Boring Machines (TBM). With the increase in difficult ground conditions and higher water pressure comes the inherent need to utilize compressed air to gain access to the TBM?s cutterhead and cutting tools. This paper focuses on one such instance in Los Angeles, CA in which Traylor Brothers Inc. performed a cutterhead intervention by compressing the heading of an 11-foot diameter tunnel to approximately 3 bar gauge pressure. This paper focuses on the environmental controls used to manage ventilation, oxygen levels, temperature, and pressure, as well as discusses the problems associated with toxic gases and the increased risk of fire. The paper will also cover the physical science of the environment and the increased risks of performing basic job functions while in a compressed air heading.

Jan 1, 2009

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By N. Chow

The recovery of manganese from lower grade resources has been studied for a number of years. Of key importance of prior work, was the discovery that higher valent manganese resource can be readily leached with sulfurous acid. This eliminates the need for high temperature reduction roasting that is conventionally used in processing high grade material. High temperature roasting is energy intensive, emits a large amount of carbon dioxide, and would not be economical for processing lower grade material. While the prior work provides important information to extract manganese from lower grade resources, the production of unwanted by-products, and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems, which to this point preclude commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low cost, environmentally friendly manner. Emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted by-products.

Jan 1, 2011

By B. K. Blashich

In responding to mine fires and explosions, accurate and timely analysis of the mine atmosphere is critical in making decisions regarding firefighting, mine rescue and mine recovery operations. For many years instantaneous analyses were available to rescue workers using handheld or portable gas detection equipment, including infrared, electrochemical, or catalytic measuring devices for a limited number of specific gases such as oxygen, methane, carbon monoxide and carbon dioxide. Instantaneous sensing technology is not available for all gases, such as nitrogen and hydrocarbons, found in a mine fire atmosphere and cross-sensitivity can be a problem with this technology. For these reasons, air samples are collected for injection into a gas chromatograph for a complete and accurate analysis for all gases including oxygen, nitrogen, methane, carbon monoxide and carbon dioxide, as well as ?fire gases? such as hydrogen, ethylene, ethane, and acetylene. This method requires additional time for transporting the samples to the laboratory near the mine, as well as an instrument operator to inject the samples for analysis. The use of a portable micro gas chromatograph with a continuous and automatic injection system has been implemented by the Mine Safety and Health Administration (MSHA) during mine recovery operations. The device directly samples the mine atmosphere from an underground location every twelve minutes and automatically analyzes the samples for all of the mine fire gases. The portable unit utilizes micro technology and the operating software has been modified to perform the calculation of sample results in and Excel® spreadsheet without user interaction. This paper describes the micro gas chromatograph system and its use at a recent mine recovery operation. The automated remote operation of the micro gas chromatograph has been shown to be a good alternative to infrared and electrochemical sensors used for mine atmosphere analysis.

Jan 1, 2009

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Figure 1). A property of Yamana Gold Inc, it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88,000 kg of gold. Crushing operations for the open-pit mine are located in a 13,500 m3 underground cavern with a ceiling height of 22 m. More than 3,600 m of tunnels are used to access the cavern and convey the ore. The Project as described in this paper relates to the design and construction of the Main Cavern, Conveyor System Exit Tunnel, the Mechanical System Access Tunnels, and two 4.20 m diameter shafts (Ore Pass #1 and Ore Pass #2) as shown in Figure 2. [ ] Preliminary engineering for the Project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc (Rizzo) was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008