Search Documents

By C. N. Greene

I am sure it is obvious to all of you that a complete program of casualty and property insurance is as necessary for any tunneling contractor as it is for anyone else involved in trade in the United States today. Going beyond those general undefined terms, there are many areas that need specific attention, particularly for contractors, regardless of size. WORKERS' COMPENSATION Workers' Compensation is mandatory in all states and the District of Columbia. In most of the states, private insurance provides this coverage. In a few states, the state operates Workers' Compensation funds, some of which are competitive with the private sector and others are operated on a monopolistic basis. Under a monopolistic setup, you have no choice, you must buy coverage from the state. Self insurance of the Workers' Compensation risk is also an alternative in most jurisdictions. With a contractor operating only in the U.S., the coverage extensions are few in number. If your work brings you anywhere near navigable waterways or land extensions thereof, you should have both U. S. Longshoreman and Harborworkers' coverage, as well as Employer's Liability coverage for the master or members of the crew of a vessel.

Jan 1, 1983

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table's reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck's slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck's slope as a result of the cross flow of wash water at right

Jan 8, 1980

By Rocky Gunderson

When operations begin early next year at the $100-million Port Kembla coal loading facility in New South Wales, Australia, a sophisticated computer system, directed by two of Hewlett-Packard's HP1000 mini-computers, will perform a number of functions ranging from monitoring and reporting arrivals and departures to maintaining a library of events for up to one year. The three-processor HP1000 system configuration, valued at $215,000, is one of the largest single orders, in terms of dollar value, ever submitted in Australia for Hewlett-Packard's line of engineering and manufacturing minicomputers. The processors will be linked in a fully "backed-up'' configuration using Hewlett-Packard's fourth generation distributed networking system, DS/1000-IV, making the system one of the most sophisticated in Australia. Interfaced to a number of weightometers and programmable logic controllers (PLCs), the computers will be the heart of a coal inventory system for the facility which, in its first phase, will be capable of handling more than 13.5 Mt/a of coal. The computers will report on all plant functions, including conveyor belt and water spray operations. Specifically, the system will: • Monitor and report all coal movements related to road and rail deliveries, dispatches from ship loaders, and interstockpile transfers. •Maintain a ''running log" of all events pertaining to overall plant operations, such as conveyor starts and stops and anti-pollution spray activation. • Accept and maintain plant data entered manually or acquired automatically from various remote locations via either visual display units (VDUs) or PLCs. • Maintain complete historical records of all transactions and related plant events for up to one year. • Provide a facility for stockpile management, modeling-type programs, and training or other simulation activity. The facility was designed with the following characteristics in mind, based on an analysis of requirements for an automated coal loading operation that would optimize productivity and be flexible to change and grow with facility needs and changing technology: • Continuous Operations-Due to the need for continuous plant logging and control, the overall facility will be capable of uninterrupted, 24¬hour operation. • Handling Current and Projected Workloads-The facility will be capable of not only handling current workloads, but also any additional workloads required during future coal loading operations. • Expansion-The facility will be capable of expansion, for a minimum cost, at any time with minimum disruption in operations. • Single Source of Supply and Maintenance-The facility will be supplied and maintained by one supplier, through hardware and software maintenance support contracts. System Configuration Two HP1000 minicomputers, each with 500K bytes of main memory, will be front-ended by a pre-processor with 256K bytes of main memory. These three systems, active, backup, and front-end, will be interconnected into a triangular array, as shown in the accompanying diagram. Under normal conditions, the front-end will transmit plant status data to one of the main systems, whose primary function will be to monitor coal flow and maintain a relevant dialogue with operators. The front-end, therefore, handles all communication with the plant PLCs, effectively removing this overhead from the current plant monitor (either of the two main systems). The front-end pre-processes and post-processes all information flowing from the plant monitor to the PLCs and vice versa, thus effectively handling all communication between the two units. A second main system will handle reporting, administrative, and modeling functions, and will also be capable of performing both front-end and monitoring operations. Linking all

Jan 11, 1981

By F. W. De Vries

A review as of the date of this meeting will cover the writer's perception of eachof the areas indicated in the charts. Changes in many are occurring with enough frequency that a detailed summary would be inaccurate within a few days of writing; for this reason, only an outline is appropriate for advanced preparation.

Jan 1, 1998

By C. D. Anderson

"IntroductionTungsten carbide is a valuable material used in a variety of different applications, including the manufacturing of cutting tools, bearings and as a cost-efficient alternative to industrial diamonds. Both the high hardness value (Mohs 9) and scratch resistance of this material make it a valuable commodity for use in the mining industry.Usually, the production of tungsten carbide is a multistep process involving one or more of the following unit operations: hydrometallurgical digestion, solution purification, crystallization (as ammonium paratungstate), calcination, hydrogen reduction and carbon synthesis. The proposed three-step process eliminates three of these steps (crystallization, calcination and hydrogen reduction) by implementing a combination of hydro/pyrometallurgical techniques. These include alkaline pressure leaching, carbon adsorption and carburization roasting. By eliminating some of the intermediate processing steps, there is potential to reduce energy consumption and decrease overall operating costs.Methods and resultsInitially, alkaline pressure leaching with sodium carbonate (Na2CO3) was employed to selectively leach tungsten, as tungstate (WO4 2-), from an industrial Scheelite (CaWO4) flotation concentrate. Experimental variables included lixiviant (Na2CO3) concentration, temperature and residence time. Experimental constants, based on previous work, were percent solids at 13 wt% and agitation at 400 rpm (Queneau and Strathmore, 1969). Leaching results showed it was possible to extract 97% of the tungsten present. The most favorable conditions for leaching were determined: 2M Na2CO3, temperature of 180° C and a residence time of 30 minutes."

Jan 1, 2015

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

By Pieter Barendsen

INTRODUCTION One of the main problems in tunneling without the use of explosives lies in the development of tools which, at an economically acceptable level, are capable of continuous breakage of the rock, resulting in a fragmentation suitable for a smooth, uninterrupted transportation of the muck away from the tunnel face. Tools employed on tunneling machines have, so far, always been of the mechanical kind which break up the rock by a crushing and shearing action. Other methods of rock breaking are possible but, even if some of them have reached the laboratory testing stage, nearly all of them are still too "exotic" to be of any practical use in the immediate future. One must admit, however, that some highly interesting results are beginning to be reported from the USA on the use of high pressure water jets for the destruction of rock through erosion, a field pioneered in Europe(USSR and Great Britain). Mechanical breakage of the rock is effected by inducing stresses exceeding its compressive/shear strength, by loading it with a wedge of cone shaped tool, until cracks are formed and chips loosened. In order to allow the tools to act upon the rock face continuously, they are commonly shaped as rotating bodies, "roller bits" or "disc cutters", spinning freely and mounted on a revolving boring head of tunnel diameter. The thrust of the tools against the face is generally exerted in a direction which is parallel to the tunnel axis.

Jan 1, 1997

By Brian Burdett, Terry I. Mudder, Robert T. Richins, James A. Stevenson, Michael M. Botz, Alan L. Wilder

The first Cyanisorb process was constructed in 1991 at the Golden Cross Mine in Waihi, New Zealand to recover cyanide from CIL tailings. The Golden Cross operation consists of an open-pit and underground gold mine with a conventional crushing, grinding and CIL circuit with Merrill Crowe zinc precipitation for gold recovery. Prior to disposal in the tailings pond, slurry tailings are stripped of cyanide at a pH of approxi­mately 7.5 using the Cyanisorb process. Mill throughput is approximately 2,500 tons per day (TPD), and CIL slurry tailings average 37% solids with a specific gravity of 1.27. CIL tailings WAD cyanide average 150 mg/L. The Cyanisorb process recovers approximately 85% of tailings WAD cyanide, produc­ing a slurry effluent with approximately 20 mg/L WAD cyanide. A second Cyanisorb process was commissioned at the NERCO DeLamar silver mine in southwest Idaho in May, 1992. The ore milling and silver recovery operation consists of crushing, grinding, a CIP circuit and Merrill Crowe zinc precipi­tation for silver recovery. Cyanide recovery is from clarified tailings with WAD cyanide ranging from 3 50 mg/L to 600 mg/L, producing an effluent with less than 30 mg/L to 60 mg/L WAD cyanide. Due to the presence of zinc-cyanide complexes in mill tailings resulting from the Merrill Crowe process, cyanide is stripped at a pH of approximately 5.5.

Jan 1, 1995

By Steven W. DeCou, Marcus R. Jensen, Stephen Navin

The Lake Mead Intake No. 2 is a project constructed for the Southern Nevada Water Authority which includes a 12-foot diameter lake tap and intake shaft constructed in over 225 feet of water; 1650 feet of 16x14-foot horseshoe-shaped tunnel leading to a forebay that is 165 feet long, 35 feet tall, and 30 feet wide; twenty-two 4-foot diameter steel lined well shafts extending 325 feet from the ground surface to the forebay; 3500 feet of 12-foot diameter pipeline crossing a bay in Lake Mead that has water depths of up to 80 feet; and 2700 feet of 9-footdiameter steel-pipe-lined tunnel. Major site grading for a future pumping station in the area above the forebay is also included as part of the project. The project is on the schedule’s critical path for completing the first phase of a $2 billion water supply program for the Las Vegas Valley. In this paper, the owner, the designer and the construction manager present a discussion of the risk management strategies that were used to control costs, minimize project delays, and facilitate problem resolution. The discussion includes an assessment of the effectiveness of the risk management strategies in meeting these objectives. This paper will be of interest to owners and engineers planning underground projects, especially those projects that present unique risks during the construction phase.

Jan 1, 1999

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread-sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin. Computerized search Computerized search approaches represent crude first attempts at letting the computer design the blend. Unfortunately, the blends found by these programs are very often less satisfactory than those developed manually. The way these techniques work is that they design, according to some predesigned pattern, a number of different blends and then quickly evaluate them. It is then straightforward to select the best from this sample set. The quality of the results depends on the number of blends designed, the way they differ from each other (the search procedure), the number of sources available, the number of quality specifications, and the severity of the specification limits. Good results are usually obtained for small, simple problems. At best, the results obtained are inconsistent from one blend to the next. Programs of this type are advertised in the mining literature. They usually mention how many different blends are evaluated, making it clear that this is more than can be tried manually. Expert systems Expert systems use a source of information known as a knowledge base. The knowledge base, usually a set of if-then rules, attempts to reconstruct the deductive reasoning process of an expert in some job capacity. For coal blending, the usual trial-and-error process has an easily recognized pattern of rules that are followed to try to find a better blend. By following these rules, it is possible to home in on the best blend without the exhaustive search required by the previous method and without the manual manipulation of the spreadsheet approach. The use of an expert system accomplishes this. One of the rules may say something like "if BTU is out of spec, then add more in the blend from a source having a high BTU and subtract some from a source having low BTU." In other words, it goes through the trial-and-error process. The process continues until all specifications are achieved and can continue further to try to optimize the cost. Of course, less simplistic rules are also needed. One set of rules would determine maximum changes in the tonnage added or deleted to the blend or from any one source. Other rules would be needed to determine which quality to improve if two or more are out of spec. At this level, the process of building the knowledge base provides the engineer with a deeper understanding of his or her own thought processes. The advantage of obtaining better blends is clear for this approach. Two more advantages should also be apparent. One is that it follows the same common sense logic that is used when doing the blends by hand or by spreadsheet, making it easy to understand. The other is that, like the search procedure, it designs the blend rather than just analyzing manually designed blends. Thus, it has all the good features of both approaches discussed thus far while providing improved results over each. A final advantage is the ease of use and ease of development. The expert system shells that are on the market are very easy to use and can be run on microcomputers. Linear programming Linear programming is an algebraic tool that solves a set of linear equations to yield an optimal solution to a problem. The optimal solution is based on the linear model so the results are only as good as the ability of the linear model to accurately portray the reality of the problem situation. It is fortunate for the coal blending problem that a linear model can be devel¬oped that reflects exactly the problem that is required. Unfortunately, the mining industry has been slow to use this tool. Coal blending applications available that use linear programming take one of three forms. The first, requiring exper-

Jan 12, 1988

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By A. Pincomb

After determining minable acreage, tons are calculated by multiplying minable acreage by average thickness and by a volume-tonnage conversion factor. Converting from tons in the ground to tons sold across the scale takes fines and internally used and wasted stone into consideration, resulting in minimum losses of about 10% for limestone and 15% for sand and gravel. A high degree of certainty about thickness, lateral continuity and geologic character defines proven reserves. Assuming continuity of these characteristics defines probable reserves. By using tpa estimations and annual tonnage requirements, the life of a deposit can be quantified. The decision can then be made regarding the necessity of securing more acreage. Some landowners choose to multiply aggregate price, operating income, or a royalty rate by tons to arrive at a value for their reserves. In doing so they probably overstate the value of their land.

Jan 1, 2003

By MSHA

Not quite a year ago, during a speech to a group of mining professionals in Washington, DC, the subject centered around the long-range importance of conducting research projects and how much that research needs to specifically apply to health and safety matters in our industry. The point was made about the critical need to work together with government, private industry, labor organizations and academia speaking with a unified voice as we all march into the future together. The fundamental benefits of competitive research were mentioned -- to improve our quality of life, to develop our energy resources, to achieve a safe and healthy environment and to ensure long-term economic growth. Very importantly, emphasis was given to the natural link that makes my agency, the Mine Safety and Health Administration, and the National Institute for Occupational Safety and Health -- NIOSH -- the beneficiaries of each other's findings.

Jan 1, 1999

By LeRoy D. Poindexter

TWO-INCH TO MINUS #100 MESH IN ONE GO The need to reduce mineral ore to a very fine mesh economically has been a timeless problem in the mining industry. With this as the specific and we.l.l focused objective, the Cyclone Crusher has been designed and is being manufactured. Utilizing space age technology from such military projects as piercing steel plate with plastic particles, the Cyclone uses the physical principles of centrifugal force. Through a combination of very high G-forces and asymmetrical loadings between a cone and anvil, particles are pulverized to very fine mesh gradation. Just how fine the final product will be, of course, is dependant on a number of factors. The machine setting, the feed rate, the gradation of the in feed material, the molecular structure of the material, and the original fracture planes of the material all affect the end result.

Jan 1, 1992

By Ludovico Sebastiao Costa, Luis Albano Tondo, Bonzi Yokomizo Santos, Nelson Roberto Garcia Munhoz

This paper focus on the productivity, cost efficiency and training programmes that have enable RPM to rank as a world class operation in production efficiency and safety achievements. The first step was to commit all senior managers to implementing the NOSA Industrial Safety System based on Management by Objectives. This focused the workforce in a specific, results-driven direction which greatly promoted subsequent performance improvements. The early operations concentrated on increasing throughput via process simplification and removal of bottlenecks. Efforts were simultaneously directed to environment, health and safety as a means to improving the quality of operations. In the last two years, improvements in mining and in-tailings dam management have further improved the cost competitiveness of RPM such as to assure its future in treating the remaining CTBl ore reserves. Promissing progress is being made in developing a viable process to exploit a remaining large resource of B2 mineralisation.

Jan 1, 1993

By Paul D. Tomlingson

Editor's note: This is the second of two articles on maintenance. Part one: "Downsizing maintenance to improve performance: Defining the downsizing task," appeared in the September issue of MINING ENGINEERING, pp. 1065-1066. Part one explained that downsizing must he an organizational change in which the mine moves to a more efficient, smaller maintenance organization. But the new, smaller organization must operate more productively. Determine initial reduction targets Reduce the workload - The initial reduction target can be determined by projecting manpower reduction as a result of discontinuing or deferring work. Start these reductions by not replacing personnel who retire or are disabled. Observe the right craft mix during this initial reduction. Improve productivity - Further reductions can come from better productivity. But achieving the higher productivity level will require a year or more. During this transition, the efficiencies of a well-defined program and a team organization must take hold.

Jan 1, 1994

By Richard R. Klimpel

The first part of this two-part article summarizes the result of a 10-year, multimillion dollar research and plant testing program involving operating mining companies throughout the world. The program was aimed at developing a better understanding of the influence of slurry rheology on the performance of mineral/coal grinding circuits. Part 1 presents the basic concepts identified, including typical laboratory results showing the influence on grinding behavior of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals. Part 2, in January, will illustrate typical industrial scale test results on both open and closed circuits using the concepts presented in Part 1. Special emphasis will be placed on identifying some industrial operating implications of controlling rheology by different methods. Introduction The industrial-scale practice of wet grinding minerals and coals in tumbling media mills (ball, rod, and pebble) is well-known to operating mineral processing engineers and plant design personnel. Over the last century, considerable experience and data has been collected, correlated, and put into rules or guidelines for successful circuit design and operation. Typical factors influencing circuit throughput that have been analyzed in some depth are mill diameter and length, grinding media size and loading, feed and product particle size, mill power use, and the interaction of classifier type and efficiency with the grinding device. Until recently, knowledge of slurry rheology influence on large scale grinding circuit performance has been limited. Even today slurry rheology effects are essentially ignored in plant design. Indeed, in most plant operations only qualitative guidelines are followed. For example, too thick a slurry causes throughput losses and too thin a slurry uses excessive water or causes water handling problems such as pumping limitations. A search of published literature and numerous discussions with experienced plant operating personnel has shown an awareness that changing the percent of solids in the mill influences grinding or the response of grinding involving fine feeds versus coarse feeds. However, most the work identified relative to rheology effects in mineral/coal grinding was qualitative. Even in the few studies that were more quantitative, the scope of the work was usually too narrow to draw general conclusions. Also, the detailed rheological characterization tied to observed breakage and the combination of laboratory to industrial-scale testing that is required to develop a broad understanding of any factor influencing grinding had not been done. In this environment, this detailed program began in 1967. It had three distinct goals: • To develop a basic understanding of slurry rheology influence on breakage characteristics in the laboratory. • To test general rheology concepts developed in the lab on the industrial scale. • To develop a commercially viable chemical approach to controlling slurry rheology that would lead to the use of chemical grinding additives or grinding aids. The goals have been met, at least in part, this year. A small fraction of the extensive laboratory and plant results have been made available in published literature. Much of the research program dealt with identifying and developing chemical grinding aids, but a lot of useful and practical information on percent solids, particle size, and slurry temperature influence on grinding circuit performance also was collected. The purpose of this article is to present a clear and concise sum¬mary of the results of the entire program. The importance of rhe¬ology control in grinding circuit behavior will be demonstrated using a series of carefully per¬formed industrial scale experi¬ments (both open and closed cir¬cuits) that have not yet been reported in general literature. Mining companies participating in the test program on a proprie¬tary basis have found the informa¬tion in this article to be useful in better understanding and improv¬ing circuit performance. Viscosity Effects in Grinding Studies In this program&apos;s previous labo¬ratory studies, it was shown that there is a consistent pattern of change in specific rates of break¬age of both mineral and coal slur¬ries as slurry fluidity changes. Using the net production rate of material smaller than some spec¬ified size-for example, kg/hr of <75 µm (200 mesh)-as an index of mill production in a standard batch mill test (with a given feed material, feed size, mill, and mill conditions such as constant time of grind), the following facts were established (see Fig. 1): • The normal range of low den¬sity, low viscosity slurry (region A) gave no variation in mill produc¬tion. The measured rates of break¬age exhibited normal first order grinding. • Grinding of a somewhat higher viscosity slurry (region B) could give increased production. The higher viscosity was obtained

Oct 12, 1982

By T. McWaters

In 1911, Miami Copper Co. began a block caving operation at its Miami, AZ property. A gravity mill was used to separate copper minerals from the Pinal Schist host rock. Until 1932, the mill tailings were deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill. In 1928, the larger and more distant Solitude tailing pile was developed. By 1932, it was receiving all tailings. In 1925, Miami Copper converted the gravity mill to flotation with sulfide copper recoveries. From 1934 to 1943, Miami, Copper ran a leach-precipitate float (LPF) circuit on mined ore and, in 1943, began sulfuric acid in-place leaching of a portion of the caved area formed by block caving. The pregnant solutions were collected underground and pumped to the LPF precipitating drums to harvest copper. In 1954, the company started mining low-grade ore. This led to the running an old LPF plant on select mill tailings from April 1957 to March 1959. In 1959, block-cave mining ceased. Solution mining became the only source of production using a launder precipitation plant. In the mid-1960s, Miami Copper merged with the Tennessee Corp. In the latter part of the decade, Cities Service Co. bought the combined properties. In 1976, Cities Service commissioned a 15-t/d (16.5-stpd) solvent extraction electrowinning(SX-EW) facility at its Miami copper property to replace the precipitation plant. In 1982, Occidental Petroleum Co. bought Cities Service. In 1983, the Miami operations were sold to Newmont Mining Corp. and set up as a subsidiary company, Pinto Valley Copper Corp. Finally, in 1987, Newmont Mining spun off a combined Pinto Valley and San Manuel unit as Magma Copper Co.

Jan 1, 1990

By John F. Shea

When tunnel boring machines were first developed, the J. F. Shea Company elected not to use them until some of the bugs were worked out. When we did take the plunge, we learned a great many lessons in tunneling; amongst others, that tunneling with a TBM is more an art than a science. One of the most important factors that contributes to a successful TBM tunnel is the geology. A machine can be designed to handle almost any type of ground; however, if the ground is not uniform, compromises in design must be made to enable the machine to handle the various ground conditions. Even when the geologic formations are well defined, it is still impossible to predict how the formations will react when it is penetrated by a tunnel. This is where the design and performance of a tunnel boring machine runs into trouble. When the reactions are adverse, the contractor is left with three alternatives; park or pull the machine and drive conventional, fight through the formation with no changes, or modify the machine. We have made all three of these choices. The first, on the Tonner Tunnel in Southern California, we encountered an extremely tough sandstone where progress was measured in inches per day. Ultimately, we pulled the machine and drove conventional tunnel. The second, on the Vat Tunnel in Central Utah, another element was added to the geology - water, which we encountered in excess of 1,000 gpm at the heading. It was impossible to adapt the machine to handle this much water, so we have been carrying out a program of grouting ahead of the machine and then driving tunnel with the tunnel boring machine.

Jan 1, 1981

By Luciano Ramos, Daniel Santos

Igarape Bahia Mine, which is currently the largest gold producer in Brazil, belongs to Companhia Vale do Rio Doce - CVRD and is situated 250 miles south of Belem, state of Para, Brazil. It came into operation in 1992 with the startup of the CIP plant, fed with high grade ore, presently at 3.4gAu/t. The ore is totally oxidized, containing extremely fine particles of free gold. The ore is soft and low cyanide consumer, with a maximum work index of 12kwh/sht. In 1993 a Heap Leaching Plant was set into operation, handling low grade ore of · 1.s g Ault. The Heap Leaching Plant has undergone two major expansions. In 1994 its capacity was raised from lMtpy to 2,2Mtpy and in 1998, with a thorough remodeling of crushing operations, it was raised again to 3.5Mtpy. The CIP plant, which was originally designed with a capacity for l. lMtpy of ore, was expanded to a 2.2Mtpy capacity in 1994. Presently, the CIP plant accounts for most of Igarape Bahia's total gold output, with approximately 220,000oz per year. Igarape Bahia's annual output is around 360.000 oz. Over the last three years, work has been intensified to improve performance of both processes, aiming at maximizing productivity of the two industrial plants. Reduced costs and increased revenues have been given a special emphasis in the unified improvement program. Cost · reduction has involved developing methodologies to rationalize consumption of materials and inputs, while increased productivity has been given top priority as a means of generating increasing revenues. Thus, all of the improvement and development efforts have had a common goal: to increase operating income.

Jan 1, 2000