Search Documents

By Kenneth S. Johnson

Western Oklahoma, with an estimated 48 billion tons of minable gypsum, has one of the largest reserves of high-purity stone in the United States (Figure 1). Gypsum beds of the Permian Blaine Forma¬tion are 10 to 30 feet thick in the southwest and northwest regions, and the Permian Cloud Chief Gypsum is 20 to 90 feet thick in the west-central region (Ham, 1962; Ham and Curtis, 1958; Scott and Ham, 1957). Republic Gypsum Company, in the southwest part of the State, is Oklahoma's second-largest gypsum producer. Since opening its plant in 1964, the company has steadily increased production and now accounts for about 15 percent of the State's annual output. The plant and quarry are 15 miles west of Altus at Duke, a small commu¬nity on the Hollis and Eastern Railroad in northwestern Jackson County.

Jan 1, 1970

[The development of economically effective and safe methods of mining thick coal seams enables to involve considerable coal reserves into the energy resources in different countries all over the world.]

Jan 1, 1975

By M. A. Vergara, J. A. Botín

"The decline of the “super cycle” has placed an end to a decade of production-focused strategies, with operating cost growing at rates higher than production. Today, the sector is placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. However, most cost management systems in the minerals industry are not conceived as value driving tools but to meet financial accounting and reporting needs. This research draws from a the development of an innovative cost management methodology that applies Activity-Based Bottom-Up cost budgeting and continuous improvement tools to develop a value-driven cost management system for sustainable improvement of operational efficiency and cost reduction. The methodology was successfully tested in the Andina underground mine III Panel sector of Corporation del Cobre (CODELCO), in Chile. INTRODUCTION Cost management is fundamental to profitability of any industrial project. Even more essential in mining, an industry that deals with commodities, which prices are dictated by the market and are beyond the management capacity of the company. The end of the mining “super cycle” and the advent in 2008 of the Global Financial Crisis (GFC), placed an end to a decade of production focused strategies, with operating cost growing at rates higher than production. The sector was placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. Many mining companies have seen themselves into the urgent need of cost management systems capable of achieving sustainable productivity gains and consistent profitability. Cost management is composed of three main processes: estimation, budgeting and control [1]. A number of conventional techniques have been used for cost estimation and budgeting for many years. However, most cost control systems in the minerals industry cannot be referred to as “cost management” since they are conceived to fulfil accounting and reporting needs, rather than to improve operational efficiency [2]. In general, conventional cost budgeting and control systems in mining use a “top-down” methodology, which lacks of necessary details, and fail as a management tool leading to undesirable results [3]."

Jan 1, 2016

By M. Canty

This paper presents results from pilot-scale and field testing of an innovative technology that uses sulfate-reducing bacteria (SRB) to treat and control acid mine drainage (AMD). Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides. The bicarbonate produced serves to help neutralize the drainage. Pilot-scale metal-removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium and 96% for copper. However, the iron and arsenic removals were not as effective as the aforementioned metals. This was largely attributed to high levels of iron and arsenic that contaminating the organic substrate. There was evidence that both adsorption and sulfate reduction were occurring within the reactors. The SRB field demonstration involved using the flooded subsurface mine workings of the Lilly/Orphan Boy Mine near Elliston, MT, as an "in situ biological reactor." In the mine, high removal efficiencies were observed for aluminum, cadmium, copper and zinc (70% to near 100%) during the four years of monitoring. However, for reasons similar to the pilot scale testing, low removal efficiencies were observed for arsenic and iron. Sulfate reduction was evident by measured decreases in sulfate and the detection of soluble sulfide within the mine water.

Jan 1, 2000

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology's development.

Jan 1, 1999

By T. M. Barczak, Zach Agioutantis

The Support Technology Optimization Program (STOP) has been developed by the National Institute of Occupational Safety and Health (NIOSH) to provide a comprehensive tool for evaluating the performance of available secondary roof support systems and designs based on support strength, convergence, cost, installation time and material handling considerations. This program uses engineering models developed from full-scale testing of numerous supports under controlled loading conditions in the unique NIOSH Mine Roof Simulator load frame to determine the support load-displacement performance as a function of the various sup- port design parameters. Both standing supports, such as wood cribs installed within the entry, and intrinsic supports such as cable bolts, can be evaluated. Support systems can be designed and compared for use in a new mining section or to evaluate potential replacements for an existing design. The support design requirements are defined from 1) estimating the failure height in the immediate roof, 2) in-mine measure- ments of support and strata interaction or development of ground reaction curves from numerical modeling, 3) the performance of an existing support system, or 4) from any arbitrary load and convergence criteria. All settings can be saved to permit resuming an evaluation in progress at a later time. This paper presents the updated MS Windows version of this tool, which can be easily installed and run on a personal computer. This Windows implementation will feature a project and application scenario setup where multiple scenarios can be assigned to one project. Scenarios can then be compared on support parameters and cost. Cost parameters can be provided either as individual cost items or using a price grouping feature. Additional support performance curves and/or additional ground reaction curves will be distributed with program updates as new information is developed. Users can also provide their own support and/or ground reaction curves.

Jun 25, 2024

By R. M. Geisenheyner

We are in the midst of a transportation revolution. From the Wright Brothers to the SST. From the Toonerville Trolly to the 120-mile-an-hour Northeast Corridor train. From Christopher Columbus to Neil Armstrong. There is another side to this revolution and it is going on every day at our mines and factories. We call it bulk distribution. Perhaps ordinary sounding, but every bit as exciting as those other transportation innovations. Basically, we have gone from bag to bulk, and in the process reached that Last Frontier in manufacturing cost savings. By revitalization of our distribution system, we have made it possible for our mines and factories to realize fully the vast economies of spage-age manufacturing techniques and accomplishments. The pacesetters in this distribution revolution have been you gentlemen, the producers and shippers of dry mineral products. In this area bulk distribution grew up. And here most of the current innovations are being introduced. Management of your industry was early to realize the economic advantages of bulk distribution. Distribution costs of your products comprises a sizeable, portion of the selling price and management is sensitive of any developments which may even slightly reduce the cost of transportation, marketing or the exploration of new frontiers.

Jan 1, 1969

By David M. Parkes, Mike Fisher

In 1947, coal production in Western Canada was 10 Mt (11 million st) which predominantly came from 120 underground mines. By 1968 production was down to 1 Mt (1.1 million st). Production in 1981 was back up to 29 Mt (32 million st), but only 1.5 Mt (1.7 million st) of the total was from underground mines. In fact, because of competition from open-pit mines, only two underground mines were operating in 1981-the McIntyre and B.C. Coal mines. While several other underground mines are being planned, this article will deal with only the two in production. Geology The geology in Western Canada is frequently complicated; hence only more regular deposits are mined. Coal is generally thick, often steeply pitched and usually soft or well cleated. The 5000-km (3,100-mile) coal belt that runs from the Yukon to Mexico is well developed in Western Canada. It is divided into two distinct regions-the Rocky Mountain Lower Cretaceous coals and the mostly uniform level Upper Cretaceous coals of the plains area to the east. Isolated pockets of coal occur at Vancouver Island and Hat Creek. Hat Creek's massive 300-m (984-ft) thick geologically recent lignite deposit is 250 km (155 miles) inland. Geography The infrastructure of Western Canada is shown in Fig. 1 along with the locations of the two mines. Both rely on exports of premium low volatile metallurgical coal mostly to the Pacific Rim. The rail distance from both mines to port is 1100 km (684 miles)-accounting for a significant portion of the sales cost of the coal. Mining Methods Two main mining methods are used-room and pillar and hydraulic. Longwall has been attempted and is being considered again. In the past, a simple hand method used gravity to help mine most of the coal on steep pitches. Levels were driven in the seam, rising slightly to assist in draining. On the advance, mining would start at the upper level, usually from adits driven in the side of the mountain. Rooms or angles were driven up 100 m (328 ft) at a suitable angle for the coal to flow down. On retreating out of the level, the pillars would be taken, starting from the highest point, using batteries to stop coal or rock flushing down the room. Batteries consisted of three to six stout wooden posts set at an angle to resist material flow. Coal loading was directly from chutes at the bottom of raises into 1- to 2-t mine cars hauled by diesel or battery locomotives. Often output was restricted by the supply of empty cars. Mechanization began in the 1960s but was difficult in these conditions. Mines such as Canmore and Coleman continued operation into the 1970s but closed because steep seams, high methane emissions, and faulting made mining difficult. McIntyre Mines The McIntyre mines are located 360 km (224 miles) west of Edmonton, Alberta, in the foothills of the

Jan 4, 1983

By D. Royston

A novel low-cost technology is described that treats excavation waters in estuarine environments where water coloration due to humic material is present, along with acidity, turbidity, sediment and salinity. The process treats all the components in the water to produce a clear (color-free) water stream that meets requirements for direct discharge to local estuarine waterways.

Jan 1, 2003

By R. D. Shackleton

Medusa Cement Company, a division of Medusa Corporation, is a medium-sized cement manufacturer serving the midwest, east, and southeast. Medusa's eight plants are located in Georgia, Pennsylvania, Ohio, Illinois, Michigan, Wisconsin, and Canada. Of these, six have active limestone, shale, clay, and sand quarries now in operation. This paper deals with the various individual state laws regulating mining and reclamation at the Georgia, Illinois, and Pennsylvania quarries. Several recommendations for future state mining laws are discussed also.

Jan 1, 1974

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by " remote control " mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation. In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term "communications" as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the philosophy behind this being to inspire other workers to achieve worth- while goals.

Jan 1, 1981

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By Michael Brittan

The AARL elution process has recently been introduced to the North American mining industry by Bateman Engineers Inc. The process is described along with its noteworthy features. Design and operating considerations are discussed.

Jan 1, 1998

By Karl E. Elers

The term "potash" denotes a family of minerals and compounds of potassium, containing greatly varying percentages of that element. In commercial usage, most of the potash products are used in agriculture, where they are used to furnish potassium, one of the three basic elements for plant growth; the other two being nitrogen and phosphorus. Potassium's contribution to plant life is principally as a stalk strengthener, and if soils can no longer supply this basic element, then crop failure is inevitable without nutrition supplied from fertilization. While agriculture uses some 95 per cent of the potash produced, other industries require highly refined potash, for the manufacture of soaps, dyes, pharmaceuticals, synthetic rubber, insecticides, photographic film, and other products. Until the mid-nineteenth century, world agriculture had three options related to the potash content of soils: 1) crop rotation and pasturing to attempt to minimize the loss of potash in harvesting, 2) abandoning depleted and exhausted soils (part of the reason for the vast migration of populations in Europe and Asia), and 3) burning forests for the use of the ashes, and concentrating the nutritional value by boiling the ashes in large kettles, for "pot - ash". With the discovery in the mid 1800's and exploitation of potash from underground deposits in Germany, the beginning of the modern potash industry was established, but American potash requirements remained substantially dependent on German production until the 1920's, when oil drilling in the Permian Basin of New Mexico

Jan 1, 1972

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By J. Owens

The methodology of quarrying changed significantly in the Indiana Limestone industry in the sixty years between September 11, 1941, the date of the Pentagon groundbreaking ceremony and September 11, 2001 when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on September 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction (and Indiana Limestone) industry can accomplish when working toward a common goal.

Jan 1, 2004

By Truman Harrington

During the last decade, diesel engine manufacturers focused their research efforts on higher efficiencies and horsepower-to-weight ratios. The result was horsepower increases of between 20% and 30%. At the same time, coolant volume decreased by about the same amount. This has made coolant maintenance more important to ensure a long life for the engine and its cooling system. Due to dilution and additive depletion, supplemental conditioners are usually added to the coolant system during an oil change. Dilution occurs when coolant leaks from the system, and water or non-conditioned antifreeze is added. Depletion is a more complicated process that involves oxidation, neutralization, precipitation and metal surface reactions.

Jan 1, 1991

By C. L. McKenzie, R. A. Heig

The design and operation of metallurgical laboratories is discussed. Laboratory size, general laboratory equipment and metallurgical staffing are discussed from a standpoint of desired laboratory results.

Jan 1, 1986

By S. Michael Feroz, Michael J. Britch, Frank S. Buehler

The City of Portland is constructing the Columbia Slough Consolidation Conduit as a part of its commitment to reduce combined sewer overflows into the Willamette River and the Columbia Slough. Known as “The Big Pipe,” the conduit has a 3.7 m. (12 ft.) internal diameter and is 5,640 m. (18,500 ft.) long. Construction Segment 1 of the project includes 250 m. (814 ft.) of reinforced concrete pipe (RCP) installed by boring and jacking. Five separate crossings were constructed beneath Union Pacific Railroad tracks and Columbia Boulevard, an adjacent arterial roadway. This paper describes the design and construction of these bored and jacked crossings.

Jan 1, 1999

By R. Torbin

The degree to Which automation/remote control/robotics has been utilized in the mining industry is far less compared to general industry because of several factors. These factors include the adverse working environment, the difficult work operations, and the generally lower incentive for capital investments in new mining equipment. Foster-Killer has been actively involved in the development of advanced mining and underground construction equipment. This equipment is designed to be remotely operated to improve both productivity and worker safety. Many of these machines employ advanced electronics and robotic features. Other types of Foster-Miller developed robots will also be described Which could be applied to special mining problems. The types of machines that will be discussed include the following: remote shaft lining/placement. remote excavation/mining operations, automated conveyor system, and robotic surveillance.

Jan 1, 1989