Search Documents

By M. Taxiarchou

The continuously increasing rate of the non-renewable raw material consumption together with the production of immense volumes of solid wastes and effluents is one of the main characteristics of our modern society. This leads to an unconditional necessity to reduce the raw material and energy consumption and to recycle the used materials and products. Life Cycle Analysis (LCA) constitutes a promising tool in this direction. LCA is a methodology, whose main purpose is the objective calculation and analysis of the environmental burdens of products, processes and activities as well as the estimation of the possibilities to perform environmental improvements in combination with the rational use of raw materials and energy. The purpose of this paper is to present the life cycle of marble and granite from the quarrying to the processing stage, including the transportation between the quarry and the processing plant, by quantifying the environmental impacts that derive from each stage and the evaluation of their potential effects to the environment and to human health.

Jan 1, 2007

By M. Liu

The use of surfactants shows great potential for the removal of hydrophobic organics from soils by in-situ washing techniques. Lab-scale soil washing experiments were performed using sodium dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that the solubility of anthracene increases linearly with an increase in SDS concentration above the critical micellar concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1993

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By George A. Hoffman, Richard J. Proctor

INTRODUCTION We will discuss here only the subway construction phase; that is, two to five years at a given location--not the long-term analysis. We also will compare some tunnel construction methods used for BART and in Los Angeles. Typically, urban planners and engineers try to balance a new mass transit system to include tunneled subways, cut-and-cover construction in city streets, and elevated guideways. Their decisions are based on many factors, most of which can be quantified. But there are some socio-economic-environmental factors which are almost intangible, or nonquantifiable, and these are rarely included in the final report for a rapid transit system. There are two reasons for this: First, it is difficult to evaluate disruptions and psychological inconveniences to individuals and to the community during the construction period, and even more difficult to assign costs because the valuations are always subjective. Second, the rapid transit project capital costs are given in the final report and the public knows them; but the intangible social costs are borne by the affected neighborhood community, not the entire city, and as such they are "hidden costs," which in fact may add as much as 25 percent to the total system cost.

Jan 1, 1974

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

By Jürgen F. Brune

The Fourth Industrial Revolution, that of digital technologies and their application, is rapidly impacting the mining industry, as it is manufacturing, transportation, agriculture, trade, and most other industries. Mining is about 40,000 years old and has its origins in Africa. Since its earliest days, it has experienced four distinct “revolutions” that each resulted in significant improvements in production, productivity, and safety and health: The First Revolution in the fifteenth through eighteenth centuries brought technologies that improved miners’ lives and health, including pumps, forced and mechanical ventilation with wind catchers and bellows, the wire rope and black powder, to name a few. Many simple, muscle- or water-driven machines have been pictured and described in great detail by Agricola who wrote De Re Metallica in 1556. Agricola was familiar with, and concerned about, accidents where miners fell off rotten, wooden ladders, acrid smoke, and dust that caused respiratory illnesses and diseases. He also knew the dangers of fatigue and recommended that miners should sing aloud to prevent them from falling asleep.

By Keith Whiting

The Little Boulder Creek molybdenum deposit is in central Idaho, in the White Cloud Range about 3.2 km (2 miles) northeast of Castle Peak, the highest peak in the range. The elevation of the deposit is about 2591 m (8500 ft). The deposit is accessible only by helicopter or by a 12.9-km (8-mile) trail from the county road along the East Fork of the Salmon River. The nearest towns are Clayton [25.7 km (16 miles) northeast], Stanley [33.8 km (21 miles) northwest], and Ketchum [45 km (28 miles) south-southeast]. The principal known deposit at Little Boulder Creek is called the "North Zone." In this zone, the molybdenite occurs both in stock- work veinlets and disseminated through metamorphosed quartzite of Pennsylvanian age. Pyrite is ubiquitous, averaging perhaps 0.05%. Scheelite and/or powellite are present in trace amounts. An intrusive quartz monzonite stock, probably of Cretaceous age, bounds the deposit on the west. A steep fault which drops Tertiary age Challis volcanics into contact with the mineralization limits the deposit on the east.

Jan 1, 1991

By Rajive Ganguli

A control algorithm was developed previously for loading coal trains such that each car met customer specifications (Ganguli, 2001). In developing the algorithm, the effect of the variance of coal was not investigated. This paper explores the effect of the variability of coal on the algorithm using two approaches: theoretical analysis and simulation. Both approaches demonstrate that variance is not an issue when the customer quality specification is close to the mine average quality. However, when they are far apart, the performance of the algorithm improves with variance.

Jan 1, 2002

By David D. Eyer

Since the decade of the 1990s is nearly upon us, I have focused on what I see are the likely trends featured in new large underground coal mines 10 years from now. I do this from the vantage point of having been involved in the installation of large mines for more than twenty years. Little of the equipment resources we have available today was unknown when I entered the coal business in 1960. There were continuous miners, longwalls and diesel-powered equipment in Europe, monitoring systems, computers, heavy media separation systems, froth flotation and conveyors then as there are now. A substantial evolutionary process has occurred with these and other mining machines and processes. Some evolved only to die out, such as boring-type continuous miners; others, such as longwall systems, flourished. My intuition tells me that since there have been largely evolutionary rather than revolutionary developments in the near past, the same is true of the future, at least for the next 10 years. In other words, the elements of what are in the future are with US now. Some, such as computer-based applications, may evolve beyond our wildest dreams -but I doubt it.

Jan 1, 1988

Overland conveyor belts that exhibit tracking problems under loaded and unloaded conditions can be tested to' determine the root cause of the mistracking. Moveable conveyors are more prone to mistracking due to structure alignment requirements. In addition, belting quality, splice straightness and carcass condition has a dramatic effect on the performance of a belt in relation to tracking. Methods are discussed that are proven to reduce belt mistracking and improve the operational reliability of the conveyor system.

Jan 1, 1995

By Victor F. Hollister

The great increase in post-World War I1 use of molybdenum was made possible by discoveries of that metal in porphyry molybdenum and porphyry copper deposits. This section documents significant porphyry molybdenum discoveries of the post-war period. The most important discovery was Henderson in Colorado. It is not only one of the world's largest and richest, but it was found by a team of geologists who defined the hood model and tested it successfully at Henderson. Under the leadership of Stewart Wallace, these scientists established a set of criteria for exploration for Henderson-type de- posits that was copied by the industry. The discovery bf vertical cylinder type porphyry molybdenum deposits was less renowned. Boss Mountain in British Columbia and then Mt. Pleasant in New Brunswick were given relatively scant notice, compared with the Henderson discovery. However, these deposits have geometrics distinct from that found in the typical hood, which directly affects their exploration characteristics. Mt. Pleasant, included in this section, is a well defined, near vertical breccia pipe. Both the Henderson and Mt. Pleasant discoveries were made by relatively small groups operating independently of the bureaucracy that characterizes large corporations. The management role in each case was one of encouragement. In addition, Wallace had the beneficial experience of working for Climax, whose objective was the discovery of porphyry molybdenum deposits. Henderson was the natural outgrowth of the exploration effort by those who studied and understood the Climax deposit.

Jan 1, 1991

By C. H. Rawlins

Deep bed media filtration is used as a tertiary treatment step (after hydrocyclones and flotation cells) to remove fine oil droplets and solids from oilfield water before reinjection disposal or to remove particulate material from surface waters used for waterflood injection. Oil and solids injection requirements are typically <5 ppm concentration at <2 micron diameter. The preferred media for produced water filtration is walnut or pecan shell, however the use of this media has evolved by trial & error and the fundamental mechanisms that occur during separation and media cleaning have not been investigated. A project was initiated to fill in this knowledge gap by analyzing the physical, mechanical, chemical, and hydrodynamic properties of six types of granular filtration media (12/20 mesh size): garnet, silica, anthracite, pecan shell, English walnut shell, and black walnut shell. Comparison of bed packing, oil wetting, attrition resistance, particle strength, and fluidization has led to an understanding of the preferred filtration media for separation of fine oil droplets and solids.

Jan 1, 2010

By D. R. Zeni

Today&apos;s mine development requires the safe, expedient and economical construction of vertical shafts for both ventilation and access. This construction must be accomplished within diverse ground conditions. Advancements in large-diameter shaft drilling have led to many exceptional mechanical refinements in shaft-drilling technology. The author traces the history of the equipment and methods employed by the large-diameter shaft-drilling industry and explores the likely paths of future development. Case histories that illustrate the adaptability of shaft drilling as a versatile tool for advanced, worldwide mining operations are cited. Safety, scheduling, costs, environmental impacts and capabilities are discussed.

Jan 1, 1996

By A. W. Hamilton

If you don&apos;t know a gauss from a grasshopper, you may be better off than you, think, particularly if you&apos;re an ore dressing engineer charged with the responsibility of selecting magnetic equipment for minerals separation and beneficiation. Gauss is a unit of measure for a magnetic field. It indicates the number of imaginary lines of force per square centimeter or per square inch radiating from a magnet. In discussing the strength characteristics of a magnet, we have come to speak of a magnetic field of 800 gauss, for example, meaning 800 lines of force per square centimeter. Gauss became the standard for selecting drum type separators many years ago under an arbitrary set of circumstances. The standard has continued to this day even though magnetics applications engineers have long considered it inadequate. The configurations of the older gauss meter were such that the most accurate and convenient readings on a drum type separator could be made at distances greater than one inch. So, an arbitrary distance of two inches was established and that two inches became the standard. Since then, it has become commonplace to specify magnetic strengths for drum separators according to average gauss readings at two inches; for example 500 gauss average at two inches, 750 gauss average at two inches and so on, even though gauss readings at two inches have much less to do with the separating and beneficiating function of a given application than was formerly believed. The standard was adopted as a means of gauging the strengths of electromagnetic drum type separators, for they were the only ones around at the time. These machines were usually designed with no magnetic considerations other than that the material to be separated should be agitated vigorously and the magnetic fields should be deep and strong. Drums built this way performed well enough, so it seemed logical to measure their magnetic strengths. Hence, gauss at two inches. Now, new improvements in magnetic techniques have made average gauss measurements at 2 inches positively obsolete.

Jan 1, 1971

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By James A. Brierley

The author has known Professor Wadsworth since the 1960s, when interest in the application of microbial technology for metallurgical processes was beginning its rapid rise. The development of bioleaching and mineral biooxidation was advanced, in part, by Wadsworth&apos;s belief in the potential for its application, as well as by his numerous contributions to the understanding of the fundamentals of hydro-metallurgy. Wadsworth is recognized for fostering research and development of the field and adding credibility to microbiological-based metallurgical processes, now often referred to as biohydrometallurgy. This Wadsworth Award is recognition of the field of biohy-drometallurgy. It is an honor to serve as a representative for all those individuals involved in research and commercial development of this technology. Modern commercial application of biohydromctallurgy began with the bioleaching of copper from submarginal-grade. run-of-mine material. Kennecott Copper successfully developed this process in the 1950s at the Bingham Canyon Mine in Utah. Other mining operations around the world followed Kennecott&apos;s lead. Today, dump bioleaching remains a very low-cost process for scavenging copper from rock that cannot be economically processed by any other method. Despite the commercial success of dump bioleaching, little effort has been made to enhance the micro Biological component of this leach process. Expansion of biohydro metallurgy into recovery of other metals did not occur until the mid-1980s, when the first commercial plant for the pretreatment of refractory gold-bearing concentrate was commissioned at the Fairview operation in south Africa. Now, processes for copper bioleaching and refractory gold pretreatment are engineered specifically to promote the activity of the microorganisms. This paper reviews the current state of commercial applications of biohydrometallurgy. It examines potential future developments and portrays the role of the microbiologist in facilitating continued growth and commercial acceptance of the technology. The commercia1 examples in this paper illustrate the expansion of microbial processing in the mining industry during the last 20 years. Copper bioleaching Early commercial applications of bioleach technology involved processing submarginal-grade, copper- bearing, run-of- mine rock in dumps. Recent applications of the technology use engineered bioleach heaps. Currently. all of these operations are in the Southern Hemi-

Jan 1, 2000

By M. K. Gangal, E. D. Dainty

The paper describes the use of portable aerosol monitors in determining real-time concentrations of diesel soot and respirable total dust in dieselized mines. The field studies were conducted in a simulated diesel environment in the laboratory where no other type of dust was present, and in four underground mines with multi-diesel machine operations. Two packages for the real-time monitoring of diesel soot were prepared which included two types of aerosol monitors: a Miniram, model PDM-3, and a Sibata, model PDS-1. These monitors utilize the principle of light-scattering to measure the airborne mass concentration in the environment. The monitoring device results were compared against the Time-Weighted-Average (TWA) values produced by the gravimetric filter sampling method, permitting calibration factors to be determined for each field test. Both instrument packages provided comparable results. The instrument calibration factors varied for different tests, which may be due to different material composition, particle size distribution, density and shape of the aerosols. This approach for real-time determination of diesel soot is found to be simple, inexpensive and easy to use. More field tests for diesel soot determination and further research on size distribution of particulates in dieselized mines are required.

Jan 1, 1989

By Joseph C. Hirschi

Mine engineers have been interested in building models that simulate mining operations since computers were introduced to the industry in the 1960s. Computer models enable operational scenarios to be evaluated without the need for actual field experimentation. Virginia Tech’s FACESIM and CONSIM, Penn State’s UGMHS, and KETRON’s CPMINE are perhaps the best known early models. Recently, SIUC has modified a Microsoft® Excel version of Virginia Tech’s Mathematical Model, calling it the SSP Model. It is used to quantify the significance of various controllable parameters. Productivity increases approaching twenty percent may be achieved where recommendations suggested by the model are applied.

Jan 1, 2005

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By John T. Gormley, Pressley L. Campbell, Harry L. Crouse

INTRODUCTION This paper summarizes an investigation conducted to determine the relationship, if any, between reported occurrences of abnormal levels of carbon dioxide (C02) gas and the construction of a 2.44meter diameter main sewer tunnel under South Eighty-Fourth Street, West Allis, Milwaukee, Wisconsin. Specific objectives of the study were to determine: (1) the sources of C02, (2) the significance of each C02 source, (3) how C02 could move to areas where it was reported to occur in abnormal concentrations, and (4) what actions could be implemented to eliminate elevated C02 levels associated with the tunneling operation. To accomplish study objectives, expertise from several scientific and engineering disciplines was required including chemistry, geochemistry, microbiology, hydraulics, and hydrology. Pertinent documents were reviewed and field data pertaining to each aspect of the study were collected as required and examined to evaluate existing conditions. Background On or about February 1, 1971, gas with a composition different from normal atmospheric air was reported to enter basements and wells of residences in the vicinity of South Eighty-Fourth Street, West Allis, Wisconsin. Examination of the gas composition revealed that it possessed an elevated concentration of C02 and a depleted concentration of oxygen (02). Public health officials who investigated the appearance of the objectionable gas concluded within reasonable certainty that the elevated C02 concentrations were associated with the tunnel construction under Eighty-Fourth Street.

Jan 1, 1979