Search Documents

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By R. Venugopal, T. C. Rao, J. P. Barnwal, K. Udaya Bhaskar

The performance characteristics of a multigravity separator for the recovery of heavy minerals of lead, zinc, copper and silver from a lead rougher-flotation concentrate were studied. Factorially designed experiments were carried out on three operating variables, i.e., the amount of wash water, the drum inclination and the drum rpm, of a multigravity separator. The experiments were carried out at two levels of each variable. With the experimental data, regression equations were developed for different metal grades and recoveries. The analysis revealed that drum speed has a major influence in determining the heavy-metal grade and recovery. Drum inclination is the next most important variable, with the amount of wash water being the least important. A concentrate containing 40% lead, 9.4% zinc, 1.5% copper and 1,400ppm silver was obtained with recoveries of 74.8%, 65.9%, 64.1% and 53.2%, respectively. Finally, the predicted values of grades and recoveries at intermediate levels are compared to actual experimental data to test the validity of the equations developed.

Jan 1, 2000

Disposal of solid and liquid wastes from mining and milling operations has become a focus of attention in recent years. Consequently, the geotechnical engineer is more frequently associated with design of disposal facilities. Jack Wulff, a representative of one consulting firm with experience in this field, talks with ME about the geotechnical engineer's contribution. Mr. Wulff, mine and mill waste disposal today is receiving more attention-and many more dollars-than in the past. Regulatory agencies have promulgated demanding requirements concerning mill waste (especially uranium mill waste) and specialist consultants are frequently being called in to design disposal systems. What can the experienced geotechnical engineer add to the development of waste disposal facilities? It's true that geotechnical engineers have recently become more visible in the minerals sector, but we've been around mining for a long time-as foundation engineers for mills and mine support buildings, and for geotechnical aspects of open pits, pipelines, railroads, roads, and so forth. We've also designed water supply dams, which could be considered recursors of tailings dams and other forms of disposal systems. Let me show by example what geotechnical engineering can contribute to waste disposal facility design. I recently was asked to look at several small wastewater impoundments which had failed. The design of the earth embankments appeared, at first glance, to be rather conservative. They were only about 3.4 m high, the slopes were 3 to 1 (horizontal to vertical), with about 24 m of bottom contact with the earth foundation. But there had been three episodes of dike failure in a few months, all upon initial filling. The problem was the nature of some material in the foundation that was also used as structural fill-a dispersive clay that readily deflocculated and eroded on contact with water, especially with seeping or flowing water. The design did not include the defensive measures required to use such materials confidently in water retention structures. Apparently, the designer did not recognize the potential problem posed by the unusual soil characteristics. That's the sort of engineering information fundamental to geotechnical engineering, but not necessarily a part of the civil, structural, or mining engineer's professional training or experience. This difference in expertise is not simply a matter of factual knowledge-it also affects the design process. The structural engineer can design a structure to fit the client's functional needs and can specify the materials (grade of steel, PVC, concrete, etc.) to meet the demands of the design. The geotechnical engineer's design process is somewhat different, since we work with natural materials, not man-made materials produced according to specification. We first have to establish what kinds of materials are available (usually directly from the chosen site, since importation of materials becomes expensive). Then we determine the engineering properties and characteristics and, finally, design the structure to fulfill the client's requirements within parameters dictated by available materials. In brief, the geotechnical engineer works with naturally-evolved, not man-made, materials and uses design techniques developed to accommodate that fact. Because no two sites are exactly alike in configuration, structural (geologic) characteristics, or available materials, there will be unique design and judgmental questions to be resolved on virtually every project. You said that water retention dams could be considered the precursors of tailings dams-you probably had a specific technical relationship in mind. There's a very strong carryover of methodology from earth dam design, where the technology developed and where it has become very refined. In designing a tailings impoundment or similar facility, essentially the same procedures of field sampling are involved (with a geotechnical engineer or an engineering geologist directing the program since representative

Jan 7, 1980

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By Michael Karmis, Emily A. Sarver, Ellen S. Gilliland, Leigh-Anne H. Krometis

"Public engagement is increasingly important in ensuring the success of projects related to energy development, particularly with regard to issues of environmental protection, public health, and socio-economic impacts. This is due to concurrent trends in public behavior, including a rise in public interest in these projects that is not matched by a rise in science literacy, and increasing organization and participation of the public through social media, citizen science, and grassroots initiatives. In recent years, several high-profile incidents have demonstrated that when public concern is ignored or met with a passive response from industry, it can rapidly grow into organized opposition that negatively impacts or wholly derails a project. Engaging, listening to, and educating stakeholders during early planning and development phases are therefore essential to earning credibility and trust. Moreover, maintaining two-way lines of communication throughout the lifespan of a project demonstrates social responsibility and facilitates cooperation, acceptance, and even support from communities and others. Positive experiences with specific projects at a local, community level can influence the larger public opinion of an entire industry sector. This paper presents cases studies of public engagement related to shale gas development (including hydraulic fracturing and pipeline construction), mountaintop removal mining, and management of mixed-use watersheds near surface mining operations. The experiences highlighted in these case studies are used to draw best practices of public engagement for sustainable energy development.Introduction Within the scientific research community, the importance of public engagement has gained increasing recognition. In a 2007 article in Nature, medical researcher, Patrick Taylor, stated that public engagement has both “gone viral” and “gone global” and has the ability to make real impacts to research (Taylor 2007). Nancy Baron, the science outreach director for COMPASS, an organization providing communications training for scientists, provides further evidence for the increasing focus on engagement, including shifting attitudes observed during her own experience as a communications coach and documented in surveys, the recent inclusion of communication and engagement activities in academic tenure review, and the surge of workshops, materials, and other resources available on the subject (Baron 2016). In addition to COMPASS, a number of organizations and institutes have been developed to train scientists for communication and engagement with the public, perhaps most notably the Alan Alda Center for Communicating Science at Stony Brook University, and academic fellowship programs, such as the Leopold Leadership Program at Stanford University and the Wilburforce Fellowship Program, have been established for the same purpose."

Jan 1, 2017

By N. S. Tombs

This paper presents the experimental results of an ongoing investigation into various properties related to the performance and durability of concretes made using existing and new cement replacements. The process of cement and concrete production is investigated focusing on product performance and environmental performance. The overriding factor for the progression of a material will be product performance however; each material selected will have many intrinsic environmental benefits. The study combines Ordinary Portland Cement (OPC) with each cement replacement candidate using the most common replacement percentages, 10, 20, 25, 30 and 50 percent. A 35N/mm2 concrete is then prepared and analysed in the fresh and hardened state. In addition, a chemical and physical analysis of each replacement material has been performed and results compared to the control samples containing OPC only and Ground Granulated Blast Furnace Slag (GGBS) as a replacement. The results show that in their present form the replacements used in this research do not compare with the strengths achieved by the controls. The right balance of chemical composition and particle grading needs to be achieved to produce a realistic replacement material. The processes required to achieve this must strike a balance between monetary and environmental cost.

Jan 1, 2006

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

By M. L. Leming

Introduction In the decades since silica gel was first identified in material exuding from cracked concrete, a great deal of research has been conducted regarding the chemical reactions between the alkalies found in portland cement and silica found in aggregates. The reaction is complex and one that is not yet completely predictable, especially from the point of view of developing specifications that are appropriate to all situations. This paper is not intended to be a rigorous review of the research findings but is an attempt to provide a simplified review of the mechanisms of the alkali-silica reaction (ASR), so that one can better understand the implications of the specifications, test results and effects on structures. In addition, the contractual relationships between the aggregate supplier and one of their major clients, the concrete supplier, will be examined with regard to the ASR. ASR basics Silica. Silica (silicon oxide) may exist in naturally occurring aggregates in various forms and in combination with a number of other elements. When the silica is completely crystalline, such as in quartz, it is chemically and mechanically stable. Quartz silica is impermeable and reacts only on the surface of the crystal, where the silicon and oxygen bonds are broken. Because the surface area per unit volume of most quartz is low, the reactivity is also low. Completely amorphous (noncrystalline) silica is, on the other hand, more porous and very reactive. The less "crystalline" the silica is in the aggregate, the more reactive. Silica that has melted and cooled quickly without recrystallizing, creating a glassy material (such as in certain volcanic aggregates), has a very low state of crystallization and will be much more reactive in an alkaline solution. Crystalline silica that has been transformed by heat and pressure may have a large quantity of strain energy stored in the crystal lattice. The presence of this higher energy will make the silica more likely to react. The "strained quartz" found in many metamorphic aggregates means that these aggregates are potentially susceptible to deleterious alkali silica reactivity, although the rate of reaction is typically much slower than with aggregates composed of or containing glassy or amorphous silicas. Another problem may exist with aggregates in which the silica is primarily crystalline. In aggregates such as chert, in which the silica exists as very fine crystals (i.e., crypto- or microcrystalline), the very high surface energies between the crystals contribute to alkali sensitivity. Therefore, the potential reactivity of an aggregate is seen to be a function of both the degree of crystallization of the silica in the aggregate and the amount of energy stored in the crystal structure, whether due to a large quantity of microcrystalline silica, a high strain energy stored in the crystals or some combination of these factors. The surface area per unit volume of the reactive silica will also affect the rate of reaction, because a larger surface area of reactive silica will have more opportunity to react. Obviously, the reactivity of the aggregate is also affected by the silica content. However, in this case, the results are not quite so obvious. A discussion of the effect of silica content will be postponed until after a discussion of the contribution of the cement paste. Paste characteristics. Hydrated portland cement is a very alkaline material with a pore solution pH typically in excess of 12. The alkaline environment of moist concrete provides an ideal place for noncrystalline or cryptocrystalline silica to react. However, not all alkalies are equal in their effects. Calcium compounds react with glassy silica to form calcium silicate hydrate, commonly abbreviated C-S-H a poorly crystalline material that can occur in several forms and chemical compositions. C-S-H was at one time called tobermorite gel, because it was chemically similar to the naturally occurring crystalline mineral tobermorite and because it had a gel-like (noncrystalline) structure when viewed under an optical microscope. The formation of C-S-H is the basis for both portland cement hydration and reaction with, for example, fly ash. C-S-H is relatively stable. Although drying will cause some shrinkage and rewetting will cause some expansion, the volume stability of the C-S-H is very good compared to the volume stability of most alkali silica gels. Alkali silica gels with high sodium contents, for example, are nonstable compared to C-S-H.

Jan 1, 1997

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By G. D. Trump, F. L. Stanley

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce the cut point and improve separation efficiency. Preliminary economic analysis show that the new circuit provides an attractive payback on capital investment.

Jan 1, 1999

By R. K. Mehta

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated for a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1989

By Robert W. Wheeler, Richard G. Ames, Robert B. Reger

Introduction The use of diesel engines as an alternate power source in US underground coal mines has been a controversial step towards more efficent mining practices. Three areas of potential benefit are foreseen. First, diesel-powered mining equipment is believed to be more efficient, resulting in less occupational risk for any given amount of production. Second, diesels are believed to pose fewer intrinsic hazards, especially those related to fires and ignition of combustibles. Finally, several other health and safety advantages are foreseen for diesel units. Each of these issues will be discussed separately. Diesel Efficiency Proponents of the use of underground diesel-powered mining equipment point to increased production efficiency due to greater maneuverability, speed, power, and payload (Bradbury, 1973; Jorgensen, 1982; Ogden, 1978; Wenberg, 1979; Olsen, 1980). Units most suitable for diesel power include LHD vehicles, shuttle cars, personnel carriers, and maintenance vehicles. Estimates of increased efficiency vary from 60%-300% and more (Wenberg, 1979). Increased diesel mining efficiency is usually viewed as making it practical to mine lower grade seams. Diesel units can also operate over a wider range of floor pitches and distances than electrically-powered units, thus allowing mining of seams with special mining problems (Olsen, 1980). Diesel application is not a universal substitute for electrical power. For example, continuous miners are unlikely diesel candidates. Reduced Intrinsic Hazards Proponents of diesel use have pointed to the increased safety potential due to a reduction in electrocutions, arcs, burns, underground cable fires, and methane ignition (Ogden, 1978). Diesel units are frequently employed in maintenance activities for lifting and moving, and for coal cleanup. Thus the case is made that diesel use, by making powered operations more conveniently available, reduces the incidence of lower back injuries and related causes for days lost due to disability (Olsen, 1980). Several other issues relating to diesel safety have also been suggested. Diesel units can continue operation even during power outages allowing, for example, personnel evacuation. The maneuverability of diesel units make them particularly attractive in difficult physical conditions, such as long haulage from the face to the belt and in areas where water is deep. The case for diesel use focuses heavily on the potential for a "per worker" reduction in accidents, or a reduction in the severity of accidents. Since accidents are a major part of the health impact of mining, a reduction in accidents and resulting injuries would make a major contribution to the health of coal miners. Opposition to Diesel Use Opposition to the use of underground diesel mining equipment in the US seems to have started with the United Mine Workers of America. Some opposition to US diesel use has been based on a widely publicized 1976 letter from NIOSH to Mine Enforcement and Safety Administration administrator Robert Barrett (NIOSH, 1982). In essence, this letter warned that while insufficient evidence existed as to diesel effects on underground coal miners, NIOSH had concerns based on prior knowledge of separate diesel exhaust constituents and the potential for interaction between these constituents and coal mine dust. Current opposition to underground diesel use has focused on respiratory health effects related to diesel emissions, particularly nitrogen dioxide (NO,), carbon monoxide (CO), and particulate content (Barrett, 1982). Through

Jan 4, 1983

By Charles Rubin

Mining is a capital- and labor-intensive business, and profitability often depends on the ability to squeeze maximum efficiency out of every piece of equipment to achieve safe production. This means keeping every mechanized drill, loader, truck and bulldozer operating at all times, and having a system to coordinate the movements of people and personnel. Mines often use wireless radios to connect equipment with management systems. But growth and changes in a mine?s profile over time can require upgrades to the wireless network. In its openpit gold mine near Carlin, NV, Newmont Mining Corp. has recently upgraded to microwave radio systems to increase bandwidth while maintaining round-the-clock uptime on its wireless network. For many of its operations around the world, Newmont uses Minestar, an operational control software system that allows administrators to dispatch equipment operators and use GPS to track the precise position of every piece of equipment in an operation. Each of the approximately 150 pieces of equipment at the mine has a radio on board. These radios connect to a network backbone that carries information between the equipment and the mine?s operations center. When traffic began to bog down on this network, Newmont upgraded to Exalt microwave backhaul systems to carry dispatch, inventory and control information throughout its operation.

Jan 4, 2010

By Richard Stahura

The longtime rule-of-thumb for conveyors was that only one cleaner was needed to solve carryback problems and help keep belt replacement costs under control. That is now being rethought. Belt-cleaning systems manufacturers, designers, and users are shifting to the view that multiple cleaners, placed at key locations on the conveyor and properly maintained, are necessary to solve today's material build-up (carryback) problems. There are still not many statistics on conveyor belt cleaning. But some recent studies support this belief. One study contends that the plant maintenance engineer's biggest problem is keeping the conveyor system running efficiently. The study also said the conveyor itself is responsible for most plant shutdowns. An unscheduled conveyor shutdown can cost more than $100,000/hr and run into millions in lost production in a given year. Other studies pointed out that belt replacement is the greatest single cost of the conveyor system. These studies allude to an important fact: cleaner belts lead to reliability and longer belt life. They showed that a critical relationship exists between characteristics of material being moved and the design of all major conveyor components. In practically all situations this relationship is keyed to belt cleaners, which have long been considered "add-ons" or "accessories." At the Fifth International Coal Utilization Exhibition and Conference, the Sammis Station-Ohio Edison Co. said it installed four belt cleaners on each problem belt. The company found that under certain conditions, when the coal is wet and sticky, carryback can be so heavy that it will flow over two cleaners. Before installing the cleaners, it was necessary to schedule a cleanup crew of four men each day and rent a large vacuum truck for an eight-hour shift. In addition, the company dredged the harbor three times a year, to remove coal spillage. Once the cleaners became operational, however, cleanup costs were reduced to a few days labor every third month. Renting the vacuum truck crew was also eliminated, and harbor dredging became necessary only once each year. In addition, the Mechanical Handling Engineers' Association (MHEA) in London pointed out that standards for cleaners are sorely lacking in the industry. MHEA called for instituting such standards in the future. They also reaffirm using multiple belt cleaners for increased efficiency. MHEA pointed out that some conveyor belts can be cleaned by one device, provided that it is correctly installed and adequately maintained. But MHEA recommended that a system approach be adopted, since this has proved more effective in practice. There are two main reasons why one belt cleaner fails to solve most carryback problems. First, management often reasons that the design of the current cleaner has probably been around for years, so it "must be good." This logic leads to a continued investment in keeping the current model operating, which includes pouring substantial sums of money in "housekeeping" manpower hours because the cleaner does not clean. Second, most single-belt cleaners are specified too late in the design process (indeed, some after the system is operational). This complicates matters since cleaning efficiency is directly proportional to when they are specified: the later the specification, the less efficiency. Cleaning equipment should be taken into consideration before the conveyor's structure is designed and fabricated. Otherwise the space available to install adequate cleaning equipment at the head pulley may be inadequate. Instead of matching conveyor with proper cleaner (as would occur during the design of the conveyor itself), designing a cleaning system "after-the-fact" becomes a matter of matching cleaner to conveyor. This limits choices in cleaners and, therefore, overall cleaning effectiveness. This is why after-the-fact designs of single belt cleaners are costly and rarely successful. While it is always best to specify belt cleaners during early design stages, the multiple-cleaner systems approach makes the timing of cleaner installation less critical. Because of flexible mounting hardware, a well-designed system can lead to 99% efficiency in cleaning and put an end to carryback even after a system is operational. Multiple-Cleaner Systems Approach In a multiple-cleaner system approach, the first step is to achieve a thorough understanding of the material to be moved under the worst conditions. With such un-

Jan 4, 1984

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By Robert M. Anderson

A popular perception by the public and many mining claimants, is that the 1872 Mining Law provides a statutory right to mine and extract minerals from the public lands. This perception in reality, is both true and false, depending on the mining claimants' ability to meet federal and state environmental, cultural and endangered species laws. Land use decisions and proposed legislation affect exploration and development opportunities in California. It is imperative that the mining industry involve itself in the planning process to ensure that BLM decision makers are fully informed of industry's knowledge and concerns. STATUTORY RIGHTS AND ENVIRONMENTAL CONSTRAINTS "No other problem has such a sense of urgency and poses as profound consequences to the quality of life and the creation and distribution of societal wealth as how we protect the environment. Certainly, the environment is the single biggest issue facing mining and mineral activities in the new decade. David S. Brown The 1872 Mining Law was passed, ironically, the same year the nation's first National Park was established. It is a perception that the establishment of Yellowstone National Park was the beginning of the United States' earliest environmental movement; brought on, perhaps, by the rapid clearing of land for homesteading purposes and, the concern that many acres of the public domain were being disposed of through a multitude of public land laws. While there was an effort being made to designate some special and unique public lands as parks for preservation purposes, environmental concern and awareness did not lead to mandatory identification of environmental impacts and appropriate mitigation until the passage of the National Environmental Policy Act in 1970. Consequently, it is not surprising that the original United States Mining Laws of 1866, 1870 and 1872 had no mention of environmental protection. There have been numerous attempts to repeal the 1872 Mining Law over the last 50 years for a variety of reasons. Currently, there is a perception by the general public, media and even some in congress, the mining industry and BLM that a change is needed. The environmental organizations want the industry to be more accountable for reclamation and post mining uses. In Tn nEnvironmental Agenda for the Future," leaders of America's foremost environmental organizations state that the mining law "includes no protection for the environment," and therefore, should be reformed. We can all acknowledge, as stated above, that the mining law, per se, requires no "protection. However, the Bureau of Land Management (BLM) clearly has the authority and the responsibility to fully "protect" non-mineral resources while providing for the extraction and processing of mineral resources by private industry. There are about 13 major federal laws that have indirectly or directly amended the mining laws to require Environmental, Historic and Cultural Protection." There have been many mining law case decisions about the statutory and constitutional rights of miners to explore open federal lands, "stake a claimg" and extract minerals. What needs to be fully understood is how federal laws, as enumerated on Table 1, may affect these rights. What follows is a description of

Jan 1, 1991

By Sol Ribakoff

With the utilization of most of the "high dam" sites for hydro-electric power and the completion of most railroad routes, many tunnel contractors were extremely doubtful that tunnel driving would continue to be an important element of heavy contracting. Experience has proved otherwise. The ever-increasing need for rapid transit and for pollution control have generated, and will continue for the indefinite future to generate, a very high level of tunneling activity. At the same time, the costs of construction have traveled an upward curve in the tunnel industry, as in all other types of construction. As a result, Owners, Engineers and Contractors have sought ways and means of constructing more economically through the development and use of labor-saving devices and techniques. The development of mining machines and lasers has contributed tremendously to such economy. Before giving you a contractor's viewpoint on Owner-Engineer-Contractor relationships in tunneling, it may be well to provide some background as to matters which give rise to that viewpoint. Construction contractors in general, and tunnel contractors in particular, have always had to contend with the physical environment in which the work has to be accomplished. However, when a building contractor has constructed his foundation, and certainly after he has "closed in", he deals thereafter with known physical conditions, or at least with conditions which he could reasonably have estimated would occur. Except, perhaps, for the hazard as to earthquakes, he has cleared Nature's threats. A tunnel contractor, however, must give thought to what the physical environment may do to his job, each and every day that he is driving a tunnel. The general consensus among tunnel men is that Mother Nature is much more likely to be murderous than motherly. Without attempting to make too much of

Jan 1, 1997

By R. P. King, S. Middlemiss

A method is developed to convert a measured distribution of fracture energies to the equivalent work index. The method assumes that the energy required to grind the material from the feed size distribution to the product size distribution is equivalent to the sum of the impact energies that are required to reduce the feed material by successive single impacts to the required product size. The method was tested by measuring the fracture energy distributions for quartz and comparing the resulting calculated value of the work index with the work index for this material measured using the conventional Bond laboratory procedure.

Jan 1, 1998

By C. Cassios

The paper covers the principles of Silver & Baryte Ores Mining Company (S&B) integrated Environmental Impact Assessment study for the whole of the extractive activity at the Fokida prefecture, over a time horizon of a quarter of a century. More specifically the paper includes: - The investigation and the evaluation of the environmental and socioeconomic variables of the specific area of concern. - The identification of the present and future impacts of the extractive activity. - An evaluation of the results of related reclamation activities. - Activity planning following a holistic approach, based on the principles of Sustainable Development, including environmental, social and economic aspects. - The monitoring of the procedure?s implementation.

Jan 1, 2003

By J. L. Fuentes

The so called 'SISCOM' is a General Purpose, microprocessor-based Monitoring and Control System, developed by AITEMIN to meet the requirements of Spanish Mining Industry in - the field of automation and data -transmission. Typical applications -are automatic control of pumps, compressors, fans and conveyors, as well as environmental monitoring and production monitoring. In relation with the last, the - System has been succesfully installed in a full section roadheader and in a mechanised steep coal face. In both cases, the main objective is to get information about running times, down times and causes, -and monitoring of other important parameters such as ventilation, methane content, power consumption..etc. Measurements concerning the face behaviour from a geomechanical point of view are also monitored. These are different pressures and stresses. All data is transmitted to the - surface and on-line analysed by a -desk-top microcomputer. The paper shows the system structure and the requirements that have - been considered on its design. Attention is given to the mechanical data acquisition problem, involving special development of some transducers. The information provided by the surface microcomputer is shown and its utility discussed.

Jan 1, 1986