Search Documents

By R. Mohr

Storm water runoff from mine facilities such as haul roads, waste disposal sites and ore bodies have become recognized as the primary facilities associated with non-point source drainage. Depending on the ore body, facility design and geographical setting, nonpoint source drainage can cause pollution impacts to local surface and ground water resources. Non-point source impacts from surface mine drainage have become an important regulatory issue for the mining industry. Implementing non-point source drainage control plans that prevent impacts to water resources can be accomplished cost-effectively with moderate labor requirements. Design considerations for plan development must incorporate parameters including contributing drainage area size, slope, flow velocity, vegetation characteristics and soil scour velocities. The success of non-point source drainage and erosion stabilization planning is based on implementing control measures that dissect drainage patterns, reduce flow velocities and disperse runoff towards sediment control sites. Interim and long-range drainage control measures should begin during exploration activities. Regulatory legislation addressing non-point source pollution sources was enacted as amendments to the Clean Water Act (CWA) in February 1987. The legislation required states to initiate non-point source pollution control programs.

Jan 1, 1991

By Wilhelm J. Kogelmann

The concept and operation of novel shaft sinking systems utilizing roadheader-type cutter booms, including mucking, conveying, and hoisting installations, are described. Selection criteria, performance data, and economic considerations for various shaft excavators are presented. Various applications of this low-cost and flexible system for civil engineering and mining projects will be discussed. The cutter booms can work in both soft ground and competent rock. Furthermore, the novel excavator can operate in ground stabilized by grouting, cementing, and freezing. The flexible cutting system can be used both for excavation of shafts, foundation pits, slopes, and for tunneling (drifting).

Jan 1, 1989

By V. Srajer

The loading and hauling equipment simulation model was developed to satisfy, the requirements and need of the mining industry in western Canada. It is expected the model will be used to determine the' impact of various combina¬tion of loading and hauling equipment, company policies and maintenance procedures, haulage requirement, to evaluate possibilities, of the use of truck monitoring and dispatch systems, and to access loading and hauling equipment productivities. To evaluate the model, and to access its capabilities in addressing the above requirements, the model was validated. The validation was based on the following: 1. Running the model in-house to evaluate its structure, 2. Running the "test case" by timing models developed elsewhere to compare the results of simulation, 3. Soliciting of model critique from outside agencies, and 4. Comparison of calculated data with real time study data. The presented paper provide overview of the validation processes and summarize" results obtained during comparison and evaluation studies.

Jan 1, 1989

By E. T. Balazs

Share of developing countries in world bauxite resources mining and processing. Technical assistance of the United Nations Industrial Development Organization to the developing world in the field of bauxite evaluation and processing. Review of selected projects of bauxite research and development aimed at creating indigenous capabilities in developing countries: "Assistance to the bauxite aluminium industry of the People's Republic of China". Project activities. UN inputs. Achievements. Follow-up. "Upgrading the scientific and technological capabilities of the Jamaica Bauxite Institute". Project activities. UN inputs. Achievements. Expected follow-up. Assistance to the establishment of an "Aluminium research, development and design centre" in India. Project activities. UN inputs. Achievements. Follow-up. "Establishment of an aluminium institute for research and development in Titograd, Yugoslavia". Project activities. UN inputs. Achievements expected. Second UNIDO group training on bauxite evaluation and processing to alumina October - November 1983 in Budapest, Hungary. Programme and coverage. Show of movie picture on organization and execution (15 minutes). Significance of UNIDO's assistance to the developing world in bauxite research and development. References.

Jan 1, 1984

By Paul C. Jones

Summitville is an old mining district located south of Wolf Creek Pass in the southern San Juan Mountains of Colorado at an elevation higher than 3500 m (11,500 ft). The Summitville mine site is about 40 km (25 miles) southwest of Del Norte. The current mine, developed by Galactic Resources Ltd. and its subsidiaries in the mid-1980s, is on the north facing side of South Mountain. The area is drained by Cropsy Creek to the east and Wightman Fork to the north, both tributaries to the Alamosa River. Mining in the Summitville area began in 1870 when James Wightman discovered placer gold on what is now known as Wightman Fork of the Alamosa River. The first vein-type deposits were located in 1873 on South Mountain near the current Summitville Mine. Mining began in the district in 1875 and continued sporadically through 1942. Major mining episodes occurred from 1875 to 1894 and from 1926 to 1942. Total gold production from the mining district through 1949 totaled 7.5 t (240,000 oz). An additional 7.7 t (249,000 oz) were produced during Galactic's tenure. Natural degradation of the outcropping sulfide-rich veins in the area and the early mining activity, including development of the Reynolds, Dexter and Iowa drainage tunnels in the late 1890s, have polluted the streams draining the area with heavy metals and acidic water. Names of the various tributaries to Wightman Fork, such as Iron, Alum and Bitter Creek, testify to this natural pollution. This degradation has reduced, or killed, aquatic life in several area creeks, including Wightman Fork, for many years before recent mining activity.

Jan 1, 1993

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By J. G. Groppo

Hyperbaric filtration was evaluated at the laboratory scale for dewatering fine coal cleaned by froth flotation. A laboratory pressure filtration procedure is described to obtain uniform cake structure from dilute slurries containing a significant amount of coarse material. Baseline tests were conducted varying filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH to determine optimum operating conditions for eventual application on a continuous pilot scale hyperbaric filter.

Jan 1, 1994

By R. Asmatulu

According to Darcy?s law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By Hajime Kitamura, Nobuharu Isago, Yuta Yamanishi, Kosuke Kawata, Hiroshi Yagi, Akira Matsuoka

Mountain tunnels are generally considered to be stable during earthquakes, however, it is known that the portal areas are prone to seismic damages. Characteristics in portals such as the location of the slope, modulus of ground deformation, and the change of overburden are different for each tunnel, and damage degrees are unclear. In this study, we reproduced the seismic behavior to investigate the effect on the tunnel portal by considering some parameters above, using simple static model tests and numerical analysis. As a result, the conditions of the slope condition and minimum distance from slope was confirmed to influence on the mechanical behavior of the tunnel portal during earthquakes.

Dec 1, 2022

By Nader Shahcheraghi, Verya Nasri, Mehdi Bakhshi, Ali Haghighat

An accidental fire load is one of the major loads considered in design of segmental linings in transit tunnel. Typically, a two-dimensional coupled thermo-mechanical finite element analysis (FEA) is conducted. The conventional approach involves using standard fire curves (temperature-time curves) which can lead to a significant overestimation of fire load and tunnel lining thickness in metro tunnels. The focus of this paper is on the cutting-edge approach, using 3D computational fluid dynamics (CFD) analysis of real train fires in metro tunnels and coupled thermo-mechanical finite element analysis (FEA) to accurately and cost-effectively design fiber-reinforced concrete (FRC) segmental tunnel linings for large-scale metro projects.

Jun 23, 2024

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By Thomas N. Walthier

Exploration is the systematically financed and technically oriented search for mineral wealth. Almost all established mining companies have an exploration department. The size of a company's search varies over the years as the company's profits, or the corporate philosophy change. While the established mining companies have exploration departments, they are also alert to acquiring discoveries made by others -- especially by prospectors and small companies without the resources to develop their find. The emphasis in some large companies stresses self-generated discoveries while others rely heavily on acquisitions; again, over the years the emphasis may alternate. In the last analysis, essentially all new mineral wealth was found through someone's exploration effort. Before we discuss how exploration is financed, it will be informative to analyze how discoveries have been made and by whom. Recently, the author conducted a survey of randomly selected major mining companies to answer these questions. Most companies responded and many went to considerable effort to give complete and detailed answers. I thank all for their help and cooperation. The questionnaire is attached as Appendix I. Appendix II is a list of the 400 companies that replied in a complete enough manner and format to be analyzed here. The results of the questionnaire are given in Table 1. Over 57% of the new orebodies acquired by 40 major mining companies during the past quarter of a century were generated

Jan 1, 1977

By A. B. Cortes

This research work discusses the development of a two-dimensional model that represents the flow that occurs in the inlet section of hydrocyclones. The governing equations are the two-dimensional, unsteady, incompressible Navier-Stokes equations in cylindrical polar coordinates with primitive variable formulations. In this approach, no assumptions have been made other than independence in the axial direction. The full two-dimensional Navier-Stokes equation in the r-a plane is used. The commonly used simplifying assumption of axisymmetry is not used. A numerical technique based on a newly developed spectral-difference method is used to solve the equations. The spectral-difference method is a multi-domain, and multi-dimensional extension of the Jacobi polynomial collocation technique. The computational grid for the inlet section is composed of 25 sub-domains which result from five partitions in the angular direction and five partitions in the radial direction. Several test cases are used to validate the appropriateness of the numerical model.

Jan 1, 1995

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By Peter L. Dunn

With the advent of new high-strength magnetic materials, rare-earth magnetic separators have become more common place for processing heavy mineral sands. In many instances, rare-earth magnets have replaced conventional separators such as electromagnetic cross-belt and induced-roll type machines. This paper will present the results from a detailed test program developed to evaluate the performance of rare-earth drum and roll separators for processing heavy mineral sands. The effect of machine design parameters, such as magnetic element configuration and separator diameter, will be reviewed in light of these test results. The impact of basic operating parameters (i.e. feed rate and roll speed) on separation efficiency will also be presented.

Jan 1, 1999

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By Johan Bosch, Wout Broere, Minh Ngan Vu

"INTRODUCTION Shield tunnelling is often used in constructing underground infrastructure in cities due to the ability to limit settlements and damage to existing buildings. However, in an urban environment with soft overburden and buildings on pile foundations such as the North-South Line project in Amsterdam, there is a tendency to design the tunnel well below the surface and below the pile tip level in order to reduce interaction between tunnelling process and piles. This results in deep tunnels and deep station boxes. When the tunnels are located close to the surface and above the pile tip level, this would reduce the required depth of the station boxes and the construction cost. Moreover, other benefits of shallow tunnels are the low operational cost in the long-term and shorter traveling time from the surface to the platforms. Still, the tunnels should be constructed in such a manner that existing buildings are not structurally damaged, which results in a minimum required distance between tunnelling process and existing buildings. In this paper, the extent of the area that is influenced by tunnelling will be investigated in order to determine the limit distance from tunnelling to existing foundations without inducing too large building deformation. From analysing empirical data of many shield tunnels, Peck (1969) firstly presented the settlement trough on the surface induced by tunnelling in soft soil as a Gaussian distribution. This is also confirmed by other authors (Cording and Hansmire, 1975; Mair et al., 1993; Ahmed and Iskander, 2010). In this study, the Gaussian curve is used to investigate the ground movement when tunnelling in order to find the effects on existing structures. Based on the results from centrifuge test and empirical data, Mair et al. (1993) showed that the subsurface settlement profile distributes as the Gaussian curve also. The width of settlement trough at the depth z depends on the depth of the tunnel z0 and a coefficient K depending on depth. Other studies by Moh et al. (1996), Grant and Taylor (2000) and Jacobsz (2003) based on Mair et al. (1993) proposed a limited change of K in various kinds of soil."

Jan 1, 2016