Search Documents

By Robert F. Goss

OCAW appreciates the opportunity given to us by the sponsors of this Conference to present our position and policies on the issue of radiation hazards in mining. Our principal concern is the health impact that the mining of uranium has on our members. OCAW represents 1,500 underground uranium miners and more than 10,000 underground miners with 3,000 in the Rocky Mountain region. The U.S. Public Health Service has determined through mortality studies that the number one cause of death among uranium miners is lung cancer. It was also determined that exposure to radon daughters and mine dust correlates with the lung cancer experience of uranium miners. Data from the U.S. Mine Safety and Health Administration has also shown that not only uranium underground miners, but all underground miners, are exposed to radon daughters -- especially underground miners in the Rocky Mountain region. It is our position that any OCAW underground miner is at potential lung cancer risk. The dosages of radon daughters that our miners are exposed to are very many times the background levels of radon exposures in the communities where they live. We are also aware that cigarette smoking accelerates the onset of lung cancer; however, it has to be clear that the available scientific evidence shows that alpha radiation does initiate lung cancer and that cigarette smoke, as a recognized co-carcinogen, promotes cancer already initiated by radiation. It is true that cigarette smoke increases the risk of cancer significantly for miners exposed to radon, but nonsmoking miners have experienced lung cancer rates twice as high as the comparable members of the U.S. population. OCAW's position is that the occupational regulatory agencies should concentrate on the exposures that can be controlled; that is, occupational exposures rather than life-style exposures. Our Union has maintained a consistent posture in relation to carcinogens in the workplace -- that is, exposure to cancer-causing agents should be limited to the [lowest feasible level]. OCAW has interpreted lowest feasible level as the lower limit of detection of the collection and analytical method used to detect the carcinogen. Our posture is based on the available scientific information on carcinogenesis. We have asked the scientific community, many times, to provide us with safe levels of exposure to carcinogenic substances, including radon daughters. The answer has been: "We cannot determine levels of exposure low enough to assure that no cancer will occur." In short, there is not a "safe threshold" for any carcinogen. This statement does not come from one of the few so-called "pro-labor scientists," it comes from the National Cancer Institute and the National Institute for Occupational Safety and Health. I don't need to be a scientific sage, then, to conclude that the lowest level of exposure corresponds to the lowest risk of developing cancer. That is, then, our policy on exposure to carcinogens. It seems there has been an attempt to ignore the fact that lung cancer in uranium miners is the principal cause of death. Uranium miners are no exception from workers exposed to carcinogens. Our policy applies to them. Uranium miners should be exposed to the lowest feasible level of radon daughters and any decrease in the permissible exposure level is a decrease in their lung cancer risk. Accordingly, OCAW has petitioned the Department of Labor for a new permissible exposure limit to radon daughters in uranium mining, which lowers the current exposure standard from 4 Working Level Months (WLM) per year to 0.7 Working Level Months per year. We made our demand to the Department of Labor on April 20, 1980. We are still awaiting action from the Federal Government on our petition. OCAW is also very concerned with other important health impacts of uranium mining. We are concerned with a rate of disabling accidents and fatalities which is twice as high as the same rate in other underground mines, excluding coal. We are also concerned with the rate of respiratory disease fatalities among uranium miners which is almost four times the rate among a comparable U.S. population. We have expressed those concerns when the U.S. Senate proposed a Federal Compensation Act for uranium miners. That proposal, by Senator Dominici of New Mexico, found a quiet death in two Congressional sessions. In conclusion, our position on lung cancer induced by radon daughters is the same position we have taken with all other industrial carcinogens: The lower the exposure, the lower the risk. OCAW is demanding a drastic decrease of the permissible exposure limits. OCAW will never accept that a segment of our membership which mines uranium should take the lion's share of the risk while the uranium mining companies take all the benefits.

Jan 1, 1981

Introduction The art of ripping has been around since the Romans built the Appian Way, but only in the last decade has ripping emerged as a close competitor with drilling and blasting in breaking up heavy rock formations. That is not to say ripping is as effective in every case, or even applicable in all cases, but it does provide a cost efficient option in many situations-if the optimum ripping techniques are used. Originally designed only to loosen hard pan, the ripper has evolved into a powerful tool, its capability increasing as the weight and horsepower of tractors increased. The tractor-mounted ripper extended the range of ripping because of the additional weight it brought to bear on the ripper tooth. Tandem ripping added the weight and power of a second tractor, extending the rippability range even further. Of course, the use of ripping depends on the type of material to be ripped. Not all rock can be ripped. Determination of rippability-an art in itself-is often inconclusive but there are certain universal principles that can be considered in the first step toward optimizing ripping techniques. Each of the three basic rock types, igneous, sedimentary, and metamorphic, exhibits characteristics that bear on rippability. Igneous rocks are the most difficult to rip because they lack the stratification and cleavage planes essential to ripping hard rock. Sedimentary rocks are generally the most easily ripped since they are built of layers differing in material, texture, color, and thickness. Metamorphic rocks vary in rippability with degree of lamination or cleavage caused by transformation from pre-existing rock. The condition of rock also affects its rippability. Although sedimentary rocks offer the best opportunity to rip and igneous and metamorphic the least, decomposed granite and other weathered igneous and metamorphic rock often can be ripped economically. Little or no trouble is encountered with hardpan, clays, shales, or cemented gravel. Likewise, highly stratified or laminated rocks offer good possibilities for ripping. However, thicklybedded rock formations generally must be drilled and blasted. The physical characteristics that favor ripping may be summarized as follows: • Fractures, faults, and planes of weakness of any kind; • Weathering, resulting from temperature and moisture changes; • Brittleness and crystalline nature; • High degree of stratification or lamination; • Large grain size; • Moisture permeated clay, shale, and rock formations; and • Low compressive strength. Ripper Types A second fundamental to optimal ripping is choosing the right equipment for a particular job. There are three types of rippers-the hinge, the parallelogram, and the adjustable parallelogram. In the hinge ripper the linkage carrying the beam and shank pivots on a fixed point at the rear of the tractor. The resulting arc from up and down movement causes up to 30° differential in the tip-ground angle. Thus, the tooth angle changes as it enters and proceeds to ripping depth. The parallelogram ripper's linkage maintains the same tip-ground angle regardless of tooth depth. This type of ripper has advantages over the hinge-type when ripping above maximum depth, but does not provide the aggressive tooth angle necessary for hard-to-penetrate materials. The adjustable parallelogram combines the benefits of both the hinge and the parallelogram rippers. It has the additional benefit of being able to vary the tip angle to the optimum angle of penetration. It can also be adjusted while moving, for the optimum ripping angle in any material. Several other factors that are important in selecting the right ripping equipment are down pressure available at the tip of the ripper, tractor flywheel horsepower, and the tractor's gross weight. Down pressure at the tip determines whether ripper penetration can be obtained and maintained. Flywheel horsepower rating determines whether the tractor has the power to advance the tip. The tractor's gross weight determines whether the tractor will have sufficient- to use the horsepower. The best ripping procedure depends on the job's actual conditions. While conditions, vary, it is still possible to apply certain proven techniques to a typical ripping situation. Caterpillar Tractor Co.'s Handbook on Ripping says optimum ripping efficiency can be realized if-before actual ripping begins-these questions and answers are considered.

Jan 1, 1983

By Jim Avraamides

The properties of activated carbon which are important for gold recovery applications include activity, capacity, wear resistance, particle size distribution and bulk density. There are experimental difficulties in attempting to simulate the plant environment in the laboratory in order to measure the above properties. However, standard tests can be set up to compare the characteristics of different carbons and to assist in monitoring the performance of carbon in CIP operations. These laboratory tests are critically evaluated and data are presented on the performance of carbon from a number of CIP plants.

Jan 1, 1989

By P. Somasundaran, A. Sivakumar

Surfactants and polymers are used in a number of processes such as flotation and flocculation. The structure of the adsorbed surfactant and polymer layers control the interfacial properties of the solid and hence an understanding of the structure of the adsorbed layers at the molecular level is essential. In this paper, a review of different spectroscopic techniques (fluorescence, electron spin resonance and Raman) used to characterize the adsorbed layers [in-situ] is presented. Information on the micropolarity, microfluidity and size of the surfactant aggregates was obtained and the growth of the adsorbed layer was followed. [In-situ] conformational states of polymers at the solid/liquid interface were determined for different pH values.

Jan 1, 1989

By M. J. Sapko

The US Bureau of Mines conducted, through joint funding with the Colorado Mining Association, large scale oil shale rubble fire tests to investigate flammability characteristics and different methods of extinguishment. Ignition of large rubble piles was easily accomplished. Foam blankets could he used to control surface flames. The results of these large scale tests confirmed that water was effective but not particularly efficient in extinguishing deep seated oil shale fires. It took up to 1.7 times as much water to extinguish afire as anticipated on the basis of a simple cooling model, assuming 100% utilization.

Jan 1, 1990

By D. F. Martin

Sustainability is typically understood as having three interrelated dimensions-environmental, economic, and social. However, far less attention has been paid to social sustainability than to the other two forms. The paper argues that one of the difficulties in giving substance to the concept of social sustainability is that it is inherently value-dependent and has major conceptual, definitional and therefore measurement issues. This is particularly the case in complex crosscultural environments such as those found in Australian mine hinterlands with significant Aboriginal populations. Nonetheless, a concept of social sustainability can provide an important counter to the usual focus on environmental and economic sustainability, and can productively guide the minerals industry in its engagement with the Aboriginal people of mine hinterlands. The paper outlines a set of principles for socially sustainable communities, and proposes means by which these principles can be implemented. It further suggests that these principles may have broader applicability than just in the case of Aboriginal people.

Jan 1, 2005

By John Conway, Gerald Bennett, John Herrick

Research efforts which have led to reduced resin bolting costs at White Pine Mine are described. Key factor was development of the capability to drill small holes (1 1/8 in. diam) in the hard (20,000-30,000 psi) White Pine roof rock. Economic data comparing the 1 1/8 in fully-grouted Resin Bolt to the conventional 1 3/8 in fully-grouted bolt is also included. The development of a method which allows the Resin Bolt to hold itself in the hole thus removing the requirement for the operator to break his "work momentum" while he stops and waits for the resin to set is also described. This technique increased bolter productivity by 23% in a recent full-scale unit test.

Jan 1, 1974

By Michael G. Nelson

In 1992, the Alaska Department of Environmental Conservation received a grant from the Environmental Protection Agency (EPA) to fund the reclamation of an abandoned placer mine. The project also included the development of a water-quality and hydrologic-monitoring program. The grant was provided under Section 319 of the Clean Water Act and is administered through EPA's Region X Water Division. For the past 100 years, Alaska's interior has been the site of extensive placer-mining operations. Early surface and underground operations left small tailings piles, some of which are still visible. Dredging left larger tailings piles, similar to those in California and elsewhere. The only reclamation of these tailings involved use as road base and fill and other civil applications. Most active mines in Alaska are on state and federal lands. The standards of reclamation for mines on federal lands are established under US Mining Laws, 43 CFR 3809. They address only mines operated since 1981. Under a state statute passed in 1990, the Alaska Department of Natural Resources, Division of Water and Mining, has issued reclamation regulations. These regulations apply to sites on state, federal and private lands, but only those mined since Oct. 15, 1991.

Jan 1, 1995

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993

By James M. Williams, Michael E. Zellars, Arthur J. Roth

INTRODUCTION Our present estimates of world P205 consumption for all uses show an average annual growth rate of approximately 1.9% per year. The estimated 1985 consumption of 41.5 million tonnes of P205 is predicted to increase to 57.1 million tonnes of P205 by the year 2005, which represents a growth from 157.7 million tonnes in 1985 to 217 million tonnes of phosphate rock in 2005. The present situation of oversupply and extremely weak phosphate product prices is, however, expected to continue in the short term and a normal supply/demand balance may not be achieved until after 1990. The growth in P205 demand, in conjunction with the higher cost of replacing low cost mines as they are depleted, will place economic pressure on world farm economies through the increased cost of phosphate fertilizers. The availability of rock supply is not the challenge; rather, it is the economics of new rock supply. This economic challenge of providing new rock supply is by no means limited to the United States. Even in centrally controlled economies, the cost of rock from domestic mines of marginal quality and economic viability, coupled with burdensome infra¬structure requirements, may result in tonnage additions at very high cost. Although government subsidies to offset higher production cost is a factor in some countries, world production in the next 20 years will be directed, if not governed, by economic factors. Established infrastructure, good quality reserves, and existing operations will provide a competitive advantage for new prod¬uction. It is our opinion that the current world supply structure will remain relatively stable through 2005, in that most of the traditional suppliers will retain supply roles. U.S. rock production, although it is not expected to grow beyond the present level, will still be a major contributor to world supply. Although dramatic changes within mining, fertilizer production and farm economics may appear disruptive, the current supply scenario will, in general, continue with the major issue being production economics. WORLD DEMAND Demand for P205 by region in the world has been estimated using projections of population, crops and yield, arable land, economic and other data as a basis for future demand projec¬tions by Blue-Johnson and Associates, our col¬laborators on a recent multi-client study. Non-fertilizer P205 demands were estimated in the same general manner. These estimates of future demand are based on an assumption of reasonable world political and economic stabil¬ity, debt repayment requirements maintained at workable levels, and resolution of problems in the agricultural economy to a point where normal supply/demand forces can interact freely to provide a basis for continued P205 supply. The results of these studies indicated an average growth rate of 1.9% per year through the year 2005. This growth could be as low as 1.5% per year, or as high as 2.5% per year. It is our opinion that the estimated rate of 1.9% per year is most probable. This moderate growth rate considers both the major economic constraints facing the world agricultural industry today and the general problem of affordability of fertilizers and other crop inputs. WORLD SUPPLY There are adequately defined world reserves of phosphate rock today to provide supply well into the future, even at much higher levels of demand than presently projected. Using the U.S. Bureau of Mines estimates, which are based on stringent criteria for definition of reserves, the present world reserves base is approximately 35 billion tonnes. Identified resources raise the potential for production by orders of magnitude. Potential resources based on geological trends, and including offshore deposits, would again result in orders of magnitude increases in rock resources. Morocco leads the world in reserves base with approxi¬mately 21 billion tonnes. The U.S. is second, followed by the Republic of South Africa and Russia. These four countries control about 87%

Jan 1, 1986

By N. Pearson, F. Calizaya

PT Freeport's mine in Irian Jaya, Indonesia uses a number of 500 m (1,640 ft) long vertical ore passes to transfer ore from the open pit to the mill. The current tonnages moved are in the order of 125 kt/d (138,000 stpd) and this will be increasing to 240 kt/d (265,000 stpd). This amount of falling rock generates high pres¬sures in the ore bins, when ore feed is terminated the pressure is no longer constrained resulting in back blasting of materials and air the ore passes. Three methods were tested to try and eliminate or reduce this problem; recirculation the entrained air, widening of the orepasses and relieving the pressure the back blast. The final method proved to be the most effective in the short term. As a long term so¬lution the orepasses are currently undergoing widening.

Jan 1, 2000

By Robert A. Haney

During the last ten years, longwall mining systems have undergone many changes. Panel widths and lengths have increased. Longwall faces have become more automated. Average production from individual longwall panels has increased from 1,000 to 3,600 tons per shift. To control the dust generation resulting from the higher production, longwall dust control systems have integrated various dust control techniques. Systems designed to control dust generated at the crusher/stageloader, shearer, and supports are common to most longwall faces. A survey was made of the dust controls that are currently in place on all the longwalls in the U.S. This survey addressed the types of controls used to reduce dust generated at the crusher/stageloader, shearer and roof support movement. Additionally, information on face ventilation rates, cutting cycle and level of automation was obtained. The purpose of this paper is to review the dust control practices that have been implemented throughout the United States and to identify those controls that are being used on high production longwall faces. Additionally, a model is used to demonstrate how ventilation and automation affect occupational exposure. Automation of roof support movement can offer some of the greatest reductions in occupational dust exposures. While technically feasible, its full benefit has not been fully realized by the industry. Until technology to fully automate longwall mining systems becomes more reliable, future dust control systems must rely on increased ventilation, application of headgate dust collectors, improved shearer dust controls and improved shield dust suppression systems.

Jan 1, 1995

By Nora M. Hutt, Kevin A. Morin

One technique for controlling ongoing acidic drainage is to relocate and submerge net-acid-generating waste rock in a lake or water-retaining impoundment. This can lead to the overall improvement of water quality and the reduction In short-term environmental liabilities. A case study of this technique is the Eskay Creek Mine in northern British Columbia. Some findings of the study are: (1) the addition of lime to each truckload of rock, based on its rinse pH, neutralized the accumulated acidity and suppressed the accumulated-metal release, (2) only 10-20% of the dump's neutralization potential had been consumed when acidic drainage appeared, (3) water chemistry in the watershed recovered roughly three years after relocation, and (4) environmental liability was reduced due to the cessation of on-land acidic drainage with no degradation of lake chemistry.

Jan 1, 2000

By Graham E. Rawlings

Geotechnical investigations for underground projects are subject to a variety of constraints, including factors such as accessibility, geological complexity, thickness of oberburden and finance. As a result, the extent of geological data available for route selection and assessment of underground design and construction problems may vary between wide limits. It is essential that the data collected, the degree to which it is representative, and the confidence with which the problems can be anticipated, should be reflected in the type of contract set up and the way in which the contract documents are written. The paper addresses the methods by which investigations can be focussed to make suitable overall ground assessments for feasibility level studies. Subsequent investigations can then be objectively directed toward obtaining data on specific geotechnlcal problems or aspects which impact tunnel, cavern and shaft design and construction. The extent of investigations at the preliminary and design engineering stages must be closely related to the geotechnlcal surveillance and control during excavation. Fixed-price contracts necessitate a secure geotechnical data base prior to bidding, and the provision of that to the tenderers. By contrast, 'design-as-you-go' contracts minimize the geotechnical information needed before construction, yet require immediate assessment of the excavated ground for determination of support requirements and payment category.

Jan 1, 1983

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements for tales for these purposes are discussed.

Jan 1, 1994

By James M. Reichman

Waterjet assist of mechanical cutters has been demonstrated in a variety of laboratory studies as well as on field equipment. As this technique becomes more widely accepted, it will be necessary to develop methods of minimizing the horsepower and water requirements. In machines such as roadheaders, continuous miners, and longwall shearers, the use of waterjet assist can be optimized through the development of phasing valves. Phasing valves will allow only the cutters in contact with the rock to be assisted. Since only 30 - 40% of the cutters are in contact with the rock, the saving power is significant. Flow Industries has developed a phasing system for use on roadheading machines. This system allows the operator extensive control of the angle of assist as well as the quadrant being assisted. This system could be greatly simplified for production machines and adapted for use in continuous miners and longwall machines.

Jan 1, 1985

By Cong Shi, Cuiping Li, Enji Sun

"Tailings dam is a subsidiary facility of mining production. In order to decrease tailings dam accidents caused by the failure of flood drainage system, this paper proposed a framework of potential failure detection system of tailings dam flood drainage facility based on three dimensional panorama technology. A collection device of three dimensional panorama is designed to capture the onsite images of flood drainage system of tailings dam. The spatial information of flood drainage facility of tailings dam is recovered through projecting the image information to spherical surface by using three dimensional panorama technology. Two dimensional images are transformed into three dimensional images in three stages of panorama images process, which are pretreatment, registration and splicing. Combined with the framework of HTML5, panorama images are embedded into webpage. These web pages have the functions of user interface that the images could be displayed, moved and zoomed. With the function of interaction with panoramic display, 3D panorama scenes can be changed and scaled. Browsing the webpage is helpful to find potential risks such as possible holes, fractures and leakages of flood drainage system of tailings dam. The realization of this system can detect the potential safety risks of flood drainage system of tailings dam. The application of this system would improve the safety and provide the ability of accident pre-warning. It is useful to maintain the healthy and sustainable operation of tailings dam.Introduction It is reported by Xie et al (2009) that tailings dam are necessary facilities for mine production and places which constructed by damming troughs or encirclement used to store tailings that eliminated after ore selection in Metal and non-metallic mines. It is reported by Mei (2012) that tailings dam is a dangerous source of high-energy man-made debris flow, the collapse of the tailings dam takes devastating damage, which seriously threatens the safety of life and property of the enterprises and the downstream residents. It is reported by Dong (2011) that the collapse of the tailings dam causes secondary disasters such as environmental pollution at the same time. It’s a serious impact on regional economic development and social stability. The phenomenon of collapse of destruction is general excessively of tailings dams in China. It is reported by Zhang et al (2011) that most of these phenomena are caused by flood over the top of dams. The main reason is the lack of capacity or the failure of the drainage system. There are also accidents caused by the failure of drainage system in foreign countries in recent years. For example, November 5th 2015, the tailing dams collapsed because of the insufficient drainage capacity of the Germano mining area in Germano Mariana area in central Minas Gerais state in Brazil. After a small post-earthquake, the liquefied tailings fill sand submerge downstream cities and towns. It finally destroyed 158 houses, killed at least 17 people, polluted 663km river and destroyed 15 square kilometres of land along the river. It is reported by Rico et al (2008) that it’s necessary to continuous monitor and control the tailings drainage system in order to reduce the occurrence of tailings accidents and guarantee the sustainable production of the mine. The traditional artificial detection methods of flood drainage system of tailings dam exist many problems such as heavy workload, low efficiency, and susceptible to meteorological conditions. And it is reported by Luo (2013) that the tailings dam wastewater is corrosive which result a certain disease in flood discharge facilities such as tailings drainage culvert, etc. In order to realize the effective monitoring, management and maintenance of flood drainage system of tailings dam, advanced technologies need to be used to acquire the information of collection and management of flood drainage facilities of tailings dam."

Jan 1, 2017

By C. Cassios

EIA is a procedure aiming the elimination of adverse impacts to the environment from undertaken projects. Historically, it starts in 1969 when NEPA (Nat.Env.Prot.Agency) in the US initiated the EIA ? EIStatement. The EIA procedure was adapted by the European Union with the directive 337/85 and in Greece the Common Ministerial Decision 69269/90 enforced it to the Greek legislation. However, mining enterprises in Greece long before the implementation of the European Directive and in accordance to the legislation of the Public Law 998/79 for the protection of the forested lands were obliged to submit EIA?s and get an approval in order to operate in forested areas. The submitted and approved EIA?s and their implementation by the mining companies were among the positive aspects of the EIA procedures. This paper is examining the impacts of EIA?s in the Greek mining industry its positive aspects as well as their difficulties and their role for the reclamation procedure. The technical and procedural aspects which EIA presents for the mining industry are commented, while proposals, for a more flexible EIA implementation for the Greek Environment are also presented.

Jan 1, 2002

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By Robert B. Hopler

For many years the explosives industry was a technological enigma: it was at the 'cutting edge' of some technologies and in the backwaters of others. For example, for at least the past 85 years, the industry routinely measured time to one-millionth of a second for determining the detonation rate of explosives. At the same time, however, formulations were usually hand-written in 'formula books,' such as the alchemists may have done. Also, due to the fact that the equipment had proven to be safe, many of the mixers and packing machines in use until recently were those patented in the 19th century; improving efficiency was not worth the possible risks that might be encountered. In recent years, the wide availability and portability of computers and their adaptation to specialized applications have revolutionized the explosives industry, much as it has many others. With the advent of the water-based emulsions and slurries (water gels), and the necessity to design totally new processing and delivery equipment, the opportunity arose to apply modern techniques to many aspects of the business. Table 1 lists some computer applications currently in use by explosives manufacturers and end users. The use of high-tech production controls, equipment design aids, field measurement devices and other computer applications is so pervasive in the industry today that any brief article such as this must be considered only as a broadbrush overview of the subject.

Jan 1, 1994