Search Documents

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By Jorgen Elbrond, Xiaoli Tang

In this paper we apply continuous-time option pricing theory (Dixit 8 Pindyck 1994) to show how to obtain an optimal investment rule for a mining project which requires sequential in- vestments. The application per se is to some extent very simple. The main purpose of the paper, however, is to draw the attention of mining people to how the option pricing theory may be used to capital investment decisions. This topic in economics is quite new but is attracting a lot of attention.

Jan 1, 1996

By Angelus S. C. Owili-Eger

The protection of groundwater resources is a growing issue on both the legislative front and within the private sector. At present, the legislative push is to establish within the Environmental Protection Agency a comprehensive research, development, and demonstration program relating to groundwater contamination and resources. It is evident that certain aspects of such legislation will be directed at the mining industry. Consequently, the mining industry must position itself to address the issues and concerns from a backdrop of facts and knowledge by developing an integrated hydrogeochemical model of the mining environment.

Jan 1, 1989

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By David Royston

Conventional straight-radial SAG mill pulp lifters suffer from incomplete discharge of the rock portion of the charge. The resulting backflow of undischarged rock limits pulp lifter performance and is the major source of wear in pulp lifters. Backflow is increased in pulp discharge cone systems where multiple channels converge towards the central diversion cone. This paper covers recent experience with pulp lifter and discharge cone design supported by a single particle motion model that illustrates the discharge and backflow characteristics of pulp lifters, including the impact of discharge cone configuration.

Jan 1, 2005

By J. A. Brierley, S. R. Hutchins, C. L. Brierley

Introduction Many gold and silver ores are refractory to conventional processing technologies. Thus, precious metals recovery is uneconomic. These resources can consist of ores, flotation concentrates, mill tailings, and other reserves. The refractory nature of these materials can be ascribed to such components as iron sulfide minerals, silica minerals, tellurides, organic compounds, and sulfosalts. Precious metals locked within iron sulfide minerals account for a large number of refractory gold ores. These minerals consist principally of pyrite or arsenopyrite. They must be oxidized to liberate the encapsulated precious metal and allow its contact with the leaching agent. Carbonaceous gold ores represent a unique class of refractory precious metal ores in general. Not only does gold encapsulation by iron sulfide minerals occur (Hausen, 1985), but these ores also contain organic matter that interferes with gold recovery by cyanidation. Direct interference can be attributed to either occlusion of gold within organic matter or formation of a stable gold-carbon complex. The magnitude of this problem is debatable. Wells and Mullens (1973) examined two carbonaceous gold ores and found no association between the gold and carbonaceous material. A more common problem is indirect interference, whereby the aurocyanide complex formed during cyanidation is sorbed by the native organic matter and is not available for recovery. This phenomenon is referred to as "preg robbing" (Osseo-Asare et al., 1984; Hausen and Bucknam, 1984). Guay (1981) summarized various methods that can reduce preg robbing during processing of carbonaceous gold ores. However, some are not applicable to carbonaceous ores that have significant amounts of gold locked in iron sulfide minerals. Several methods exist for oxidizing iron sulfide minerals and rendering refractory precious metal ore amenable to conventional recovery processes. These include various embodiments of roasting (Jha and Kramer, 1984; Brown, 1984; Arriagada and Os-seo-Asare, 1984; Smith, 1986), pressure oxidation (Muir et al., 1984; Beattie et al., 1985; Thompson, 1986; Weir et al., 1986; Argall, 1986), and chemical oxidation (Scheiner, 1971; Jackson, 1983; Van Weert et al., 1986). Each process has been successfully used for refractory precious metal ores. In many instances, however, their use is precluded by capital and operating costs relative to the value of the ore. An alternative to these methods is microbial pretreatment - a biological process whereby iron sulfide minerals are degraded and the liberated precious metal values can be recovered by conventional technologies. Bioleaching refractory precious metal ores is a relatively new concept compared to roasting and chemical oxidation. It is rapidly becoming established as a viable pretreatment alternative. Numerous studies have been conducted in the laboratory and on a pilot scale (Yudina et al., 1979; Lawrence and Bruynesteyn, 1983; Pol 'kin et al., 1985; Marchant, 1985; Livesey-Goldblatt, 1985; Gibbs et al., 1986). Comparative tests have demonstrated that bioleaching can be equal to or better than roasting or pressure oxidation in terms of product recovery and process economics (Fridman and Savari, 1983; Livesy-Goldblatt et al., 1983; Karavaiko et al., 1985; Gilbert et al., 1986; Hackl et al., 1986). Bioleaching's main drawback is that pretreatment requires days rather than hours. This can lead to excessive operating costs for difficult-to-treat ores. In all of the tests reported thus far, the leaching microorganism used has been thiobacillus ferro-

Jan 4, 1988

By James E. Monsees, Wayne A. Carbiener, Michael R. Wigley

This paper illustrates an approach to quantitatively document the degree of technical conservatism to be incorporated into the design of a waste isolation system in bedded salt. It is anticipated that for an actual repository site the key performance constraints and/or design bases identified in this paper will be reviewed, and modified or supplemented as required. Ultimate acceptance of a repository will be dependent upon scientific peer input and scrutiny of the demonstrated conservatism inherent in each specific repository site and design.

Jan 1, 1981

By Z. B. Yin, R. W. Bartlett, P. R. Taylor

Tube furnace experiments have been performed to evaluate the lime roasting of pyrite in air. The sulfur volatilized was measured over time. Variables studied included: form of lime, sodium sulfate additions, temperature, air flow rate, lime to pyrite weight ratio and pyrite particle size. It was found that more than 98% of the sulfur can be retained at a reactor temperature of 650°C, with a slight excess of calcium hydroxide. The roast products are primarily hematite and calcium sulfate.

Jan 1, 1990

By Michael T. Ballard

The key to productive computer usage is system software integration with full compatibility among individual components. The majority of software developers in our industry are still in the process of perfecting individual components. As a result, exchange and validation of data between disciplines becomes an arduous process. We at Morrison Knudsen Engineers, Inc. (MKE) have integrated an entire system, allowing exploration, geology, modeling, mine planning, and operation modules to work as a single, complete system with direct exchange and validation of data. The importance of integration to both developers and users of today's mining soft- ware is becoming increasingly apparent as we, an industry, move toward growth and enhancement of the technology of ore reserve acquisition, evaluation, and management. It is also important to understand the present state of integration and where it is leading US. Not long ago, another industry passed through the same stages we are now setting up for the mining industry. The stereo industry began with a few individual components, the record player, tape recorder, and radio. People were able to play records, listen to the radio and record conversations and music only through microphones on their tape recorders. Soon, one enterprising individual discovered he could tape sound directly from the radio or record player by capturing audio output from the speaker wires. Interfaces and patch cords were developed, providing a means to transfer audio information between components with not only little loss of sound quality, but also the elimination of back- ground noise. The industry took another step forward with the introduction of "integrated" stereo, where the components were packaged in one cabinet with shared resources. This reduced overall cost which paved the way for better quality. Today's stereos are now so well integrated that many of the components share data and resources from the same manufacturer, designed to work together for almost perfect data transfer between any of the components. The result is better sound, convenience, and reduced cost. This is the ultimate goal for integration. Any system development passes through these same steps on the road to total interaction. Initially, the components are designed, tested, and marketed individually, often by separate companies. As the users become familiar with the components, the need arises for an automatic interface between the components. This is necessary to cut down on error during data transfer and to eliminate the redundant work required to enter results from one component into the next component in the system. As a result, interfaces must then be developed to aid in this data transfer. After data transfer is accomplished, the next step is resource sharing. Resource sharing is careful design and engineering by either cooperative, individual manufacturers or one firm taking on the task to produce a single package product. Design and resource sharing leads to lower overall cost, while still providing component capability with options to grow as the user grows. The mining software industry has been working to develop some very high quality component software and has indeed accomplished this task in every aspect of the mining industry. However, realizing the importance of integration, some companies with limited individual resources have started working together to interface their individual components. Other firms have undertaken the project of developing complete, integrated systems.

Jan 1, 1987

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By R. C. Oberth, C. F. Lee, E. M. Taylor

INTRODUCTION Underground siting of nuclear power stations is drawing increasing attention in various parts of the world. Scandinavian countries took the early lead in this field because of their experience in the design and construction of underground hydroelectric stations and industrial plants, and because they have near-surface rock formations which are ideally suited for hosting large underground caverns. The world's first underground nuclear facilities were built in Norway (Halden) and Sweden (Agesta) and were commissioned in 1959 and 1963 respectively. Figure 1 summarizes the main features of these and two other small-scale European facilities. (1-4) American utilities and regulators are also for a variety of reasons assessing the benefits and penalties of underground siting. A recent study by Sandia Laboratories (contracted by the Nuclear Regulatory Commission (NRC) focussed on identifying potential safety benefits of underground siting. (5) Although the study concluded that underground plants would have improved containment for some accidents, as well as better external protection, NRC, in assessing the overall benefits and penalties, decided not to impose mandatory underground siting for nuclear stations. In June 1976, the California Legislature enacted a law which directed the California Energy Commission (CEC) to examine the issues concerned with underground siting of

Jan 1, 1979

By P. Lausch, R. A. Mercer, J. F. Archibald

An innovative, polyurethane-based, spray on rock-lining material, designated Mineguard™ by its developers, is being manufactured to provide rapidly deployable area support coverage for specific use in underground hardrock mines. This form of surface-coating agent is intended to replace both shotcrete and the screen component of bolt-and-screen support systems. Due to the rapid rate of application, ease of installation and ability to achieve a 90% cure within seconds of application, Mineguard™ has considerable potential for use in mining and excavation operations that require a rapid rate of advance and a high degree of automation.

Jan 1, 1996

By P. K. Kaiser

A rational approach for the design of fully grouted bolts in underground excavations is presented. An analytical model involving elasto-plastic concepts and the mechanics of bolt/ground interaction was developed and tested by comparison with laboratory tests and field measurements. The theory elucidates the influence of shear stress distribution, bolt pattern and geometry on tunnel convergence. Laboratory simulation has provided convincing evidence to support the theoretical predictions. A dimensionless bolt efficiency parameter is introduced as a design tool that relates the reduction of tunnel convergence to the bolt length and density. Its application in practice is highlighted by the analysis of one case history.

Jan 1, 1987

By B. Moudgil, M. Bogan

A mathematical model, based on first-order kinetics, is derived to describe batch settling data. The model is used to predict the settling behavior of solid suspensions under different conditions. The potential benefits of this model to solid-liquid separation processes are discussed.

Jan 1, 1994

By I. Iwasaki

There are many reasons why the US mineral and primary metals industry is in its present state. Undoubtedly, a flood of imported goods in all sectors is playing a major role in the plight of our raw materials industry. Domestic industry is becoming increasingly aware of the importance of its international competitiveness. And we are beginning to wonder what is happening to our technological edge. A number of factors affect the international competitiveness. Engineers cannot do much about some of these factors - labor costs, tax policy, government relations, interest rates, dollar strength, and labor-management relations. Something can be done about technology, however. Some say technology is so easily transferable today. But I would like to believe that we have the ability to apply it better than others. Not too many years ago, "made in Japan" meant cheap and shoddy products. Today, Japan has completely changed its image. The US is beginning to feel the threat from Japan's low-cost, defect-free products with dependable delivery. With worldwide recession and the strength of the dollar, we were shocked at the sudden weakness that developed in America's industries, not only in the international market, but domestically as well. What went wrong and what can we do about it? Senior executives from 300 large American manufacturing companies were surveyed. These executives believe US companies must: • invest in more efficient plants and equipment (27%); • invest in more research and development (23%); • improve the quality of service to customers (23%); and • adopt more aggressive marketing tactics and strategies (14%). Are we not doing enough research? The US has nearly four times as many people engaged in research and spends four times as much for research as Japan (Fig. 1). There is little doubt about the excellence of the US performance in basic science as indicated by the number of Nobel prize recipients. Japan has produced only four winners since World War II. Look at technology trade of five countries (Fig. 2). Again, US performance has been remarkable. An interesting observation here, is that the United Kingdom, another country with economic woes, is also in the black, West Germany and Japan, both with trade surpluses, are net technology importers. It is apparent that the US' performance in the commercialization of new knowledge is much more in question. Japan had $50 billion of trade surpluses with the US last year, which led to some friction between Washington, DC and Tokyo. Comparing the technology trade of Japan and the US in more detail, Japan imports disproportionately large amounts of technology from the US and Europe. This data is rather old, 1978, but the general trend is not too different even today. It is generally believed that scientific research leads to innovative technology, then to economic payoff. But, after seeing the current technological challenge by Japan, we are forced to change this traditional view. Investment in research may eventually lead to economic payoff, but not directly. There is a middle ground between new knowledge and its commercialization. This is an area where the Japanese have been successful. Until the 1970s, many western companies licensed patents to Japan for quick profits. But, in recent years, these companies have become more discrete about the terms of technological transfer. As a result, a number of scientists and engineers are expressing deep concern over the future of technological developments in Japan. A survey was conducted on 450 research managers of private industries in Japan on how they viewed the level of breakthroughtype original research in Japan as

Jan 6, 1986

By Daniel Tempelis, Tom Freeman, Eric Fordham, John Shamma, Steven Duke

The Arrowhead Tunnels in southern California are being completed by MWD under stringent groundwater in?ow limits established by the U.S. Forest Service. Pre-excavation grouting, new TBMs and a bolted, gasketed, pre-cast concrete segment initial lining are employed to control water in?ows. The effectiveness of prescribed water control measures was analyzed using conservative assumptions with the analytical techniques described by Goodman (1964), Heuer (1995), and numerical modeling. Analyses results suggest groundwater in?ows to the tunnels can be maintained well below the limits with aggressive pre-excavation grouting balanced against a reasonable rate of advance and quality erection of the initial lining system.

Jan 1, 2003

By Maurício L. Torem, Isabella A. Scorzelli

Taboca Mining is one of the largest producers of tin in the world. In its pilot plant, significant amounts of a middling of 90% xenotime (YPO4) and 10% zircon (ZrSi04) are produced. Until now, these minerals of this ore body could not be separated successfully. This paper presents some aspects of the fundamentals of xenotime and zircon flotation with anionic (fatty acids) and cationic (amine acetate) collector, as well as the influence of the superficial leaching of the minerals with cold HCI and HNO3 on the floatability. The mineralogical studies showed that both minerals are optically liberated in -212+106 µm size fraction. Surprisingly, SEM analysis indicated that both xenotime and zircon contain very small inclusions (1-5 µm) of thorite (ThSiO4). On the other hand, zircon is fairly metamictizated giving rise to malacon. Zeta potential tests showed that the isoelectric points of xenotime and zircon correspond to a pH value of 4.5 and 4.7, respectively.The pretreatment with HCI and HNO3 displaced the isoeletric point (IEP) of the minerals to the left. The microflotation tests indicated that the floatability of both untreated and treated minerals are quite similar in the presence of the collectors studied in this work. Adsorption mechanisms are also suggested.

Jan 1, 1995

By Hisakazu Matsushita

1. Introduction This is a report on applications of the earth pressure type balanced shield tunneling projects executed under narrow streets on soft alluvial layers in Japan. Japan is a long island country surrounded by the sea. Steep mountain ranges run along the archipelago and numerous rivers originate from the mountains, leaving only limited areas of flat land along the upper and middle reaches of the streams. The majority of cities in Japan are on soft alluvial layers. Alluvium represents an extremely complex soil formation, sections bordering diluvium being characterized by sharp undulations. Various difficulties are therefore encountered in shield tunneling work undertaken in such ground conditions. Particularly, at work sites lying in an unstable, waterbearing layer with high permeability, shield excavation becomes utterly impossible, hampered by large amounts of underground water as well as land collapsing caused by the water. Even when work can somehow be accomplished by using chemical grouting or by lowering ground water level, which require extra expenses and time, undesirable effects such as ground surface settlement are unavoidable in projects undertaken in the past. The newly developed method allows safe and accurate tunnel excavation at normal speed and without giving any adverse effects on buildings above, even under such unstable ground conditions. An outline of this new method was announced at the "International Tunnel Symposium '78" held in Tokyo, and the method has since been employed in a number of tunneling projects in this country. This report provides further data on the new method with reference to some of those projects, explaining how it allows tunnel excavation with

Jan 1, 1979

By Antonieta Middea, Rupen Adamian, Fernando F. Lins

This work presents the results obtained with aggregation of fine talc (-19 m), a naturally hydrophobic mineral, in the presence of KC1 solutions. The classical DLVO theory describes well the aggregation of talc in dilute KC1 solutions. Beyond 1 M KCI we have found indications that a non-DLVO interparticles force is operative, say an hydration (repulsive) force. This structural force could be responsible for the unexpected re-dispersion of talc suspension. However, no repulsive force (depression) has been observed in salt flotation of talc at higher ionic strength, up to 3 MKCI.

Jan 1, 1995

By A. R. Bath

During the late 1970s, pilot mining tests carried out on manganese nodules in the Pacific Ocean and metalliferous mud in the Red Sea demonstrated the technical feasibility of deep sea mining operations. However, the production of manganese nodules on a commercial scale is subject to numerous technical problems. As a result, a German-French joint development project has been underway since 1985. This venture focused on three key points: nodule pick-up device, locomotion of self-propelled collectors and hydraulic lifting of nodules. This paper presents the scope of this research and development program, its main results to date and future prospects.

Jan 1, 1992