Search Documents

By P. Pal Roy, Ajit Raj Ostwal, M. M. Singh

Field investigations have revealed that sawdust can be used as an efficient additive to ANFO for carrying out production blasts in limestone mines. Sawdust can be used at a reasonably reduced cost without sacrificing fragmentation, muck profile and wall control. Such additives lower the detonation pressure of ANFO by acting as low-grade fuel that reacts or burns more slowly in the presence of ammonium nitrate than does fuel oil. On detonation, it eventually forms near-ideal oxygen balance that helps in liberating maximum energy to break the surrounding rock. It also forms a low-density stable mixture that helps in reducing loading density (kg/m) of explosive in the blasthole. Experiments performed at the Hirmi Limestone mine, M/s L&T, and at the Lambasta Limestone mine, M/s Jaypee Rewa Cements, showed the novel acceptance of the technique in a highly competitive market where cost reduction has been a major area of thrust.

Jan 1, 2003

By A. D. Davis, C. J. Webb

Brohm Mining Company's Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February of 1999 the Governor of South Dakota announced plans to request the U.S. Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable ground-water reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2002

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using discrete system simulation. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution used in a random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing needed and provides verification of how representative the samples are.

Jan 1, 2002

JIM ARNOLD: Questions? Comments? Gary, were you gone when I made the comments about corporate puke? [laughter] SPEAKER: You were hiding. BRUCE CAVENDER, BHP Copper: Having worked in both places, I'd like to address the issue of the plant versus the corporate office. One thing to keep in mind is that we are all very engaged with the technical elegance of a lot of the work we do. There's some tremendous technical expertise in the plant. But remember, the guys in the corporate office are only thinking in one denomination, and that's dollars. So we'll see something like a spill, and for us it's a problem. At the end of the day, what the corporation cares about is the financial impact. So we've got to be careful to couch our solutions in dollar terms. JIM ARNOLD: Rebuttal? [laughter] DOUG HALBE: Are you going to rebut this one, Andy? ANDY CARTER, Oxidor Gold Corporation: No, I don't think so. I'm not up to it. I'd just like to address a question both to our panel and the floor. Those of us who've been in this industry any length of time have seen these same mistakes made over and over again. Wherever you go, year after year, plant after plant, you see the same problems. I guarantee you, Doug, that if we have a similar conference down the road, you're going to see the same thing. My question to the panel and to the floor is what is it about our industry that stops us from learning from our mistakes? What characteristic is it that prevents us from learning and makes us repeat the same mistakes over and over again? DOUG HALBE: That's a great question. Someone said in a meeting 10 years ago that if the people who design plants designed airplanes, the planes would be falling out of the air all the time. GARY SIMMONS, Newmont Gold Company: I've got an answer to your question as to why many plants are poorly designed. It's that the minute anybody demonstrates any sort of competence in plant design, they're promoted to a higher-paying job, and the talent pool is left with people of lesser experience. Just think about it: The people who have the experience and have demonstrated it more than once have moved up. JIM ARNOLD: I think that there's another reason, too. Seven or eight years ago I was chairing a session, and I challenged everyone in the session to some day publish an article about the design mistakes they'd made because we never talk about our mistakes. I'll

Jan 1, 1998

By Thomas J. Rudolphi

Efficient transport of bulk materials by belt conveyor systems is an important engineering design issue, especially as conveyors become longer and power requirements increase. It is well known within the industry that the parasitic energy loss of a belt conveyor, due to the indentation of the idlers into the belt backing material can be upwards of half the total energy required to drive it on a horizontal flight. Other loss sources includes the rolling resistance of the idlers, belt/roller misalignments, material trampling, frictional and acceleration losses on loading, etc., but energy absorbed by indentation of the belt backing as it passes over each successive idler is the dominant power consuming factor. INDENTATION LOSS MODELS Models to predict the rolling resistance of a cylinder (idler) on a viscoelastic foundation (backing material) have been available for some time. As a contact problem, it is nonlinear (contact length or indentation depth is a dependent on the load and vice versa) in load/deformation response. Rubber backing material is generally assumed to behave as a linear viscoelastic solid, even though it is known that most rubber compounds retain linearity only at very low strains. Because completely general solutions are impossible, practical solutions require simplifying assumptions. Those assumptions relate naturally to two separate pans of any analytical model: I. The deformation model-aspects of the problem relating to the geometry, boundary conditions and kinematics of how the material deforms. 2. The material model-aspects of the problem relating to the material properties, or constitutive relationships, i.e., the stress/strain relationships.

Jan 1, 2008

By Glenn Boyce, Paul Gribbon, Gary Irwin, Greg Colzani, Jim McDonald

This paper discusses the process utilized by the City of Portland Oregon’s Bureau of Environmental Services (BES) to procure and compensate Impregilo-SA Healy (I/H)for the West Side Willamette River Combined Sewer Over?ow (CSO) Project. The contract method is a three-phase process consisting of qualifications based contractor procurement, pre-construction phase design assistance/construction planning, and facility construction where the contractor is compensated on a cost reimbursable-fixed fee basis. The paper focuses on pre-construction phase lessons learned from the development of the contract general conditions, establishment of a construction budget and cost control program, incorporation of contractor recommended design changes, and development of a subcontractor procurement program for construction.

Jan 1, 2003

By M. Misra, I. Anazia

The dispersion of oily collector has a significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. Such dispersion and reagent addition techniques are invariably inadequate and nonselective. A new collector addition technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This technique involves atomization of the collector into the air stream. Under these circumstances, an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the air phase (continuous with respect to oil), and the air phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and, most significantly, increases the flotation rate of ultrafine coal. Atomization of collector/frother combinations yielded improved flotation recovery and maintained near uniform froth levels, which is a desirable feature in coal flotation. Microscopic examinations of the attachment of oil- coated bubbles at a coal surface were conducted by attachment time and contact angle measurements. Oil-coated bubbles attach at significantly faster rates and with a higher contact angle than oil-free bubbles.

Jan 1, 1988

By J. W. Oberholzer, C. F. Meyer

The increased use of continuous miners to extract thicker coal seams has necessitated the use of enhanced ventilation systems in the headings. Due to the increased face size, more ventilation is required to effectively dilute the liberated methane down to acceptable levels. If more air is directed to the face an increase in the entrainment of dust creates an increased potential for workers to be exposed to dust. To enable the ventilation systems to reduce the methane levels and the levels of the airborne dust the ventilation systems in the heading have to be carefully designed. The matter is made more complicated through the use of other ventilation methods like jet fans, air-moving sprayfans on the continuous miners and high capacity scrubbers on the continuous miners. To enable the design of a balanced ventilation system in seam heights of over five metres requires methods that consider the system in a three- dimensional manner rather than in a two-dimensional fashion. Through the use of computational fluid dynamics (CFD) coupled with appropriate methods of taking underground face ventilation readings these problems can be solved in a cost effective way. Using computer modelling, ventilation methods can be designed and assessed instead of using costly underground trials to test the alternatives. Use of this system has led to a higher level of ventilation design as well as a more effective method to combat the health and safety hazards in coal mine headings.

Jan 1, 1995

By G. J. Melvin

Mines the world over tend to face a common range of problems. They begin life by trying to determine if there is sufficient product, usually under tons of earth, of sufficient quality to justify the operation. Once such a determination is made the mine must then be planned and brought into operation. Once operating most mines find that they are far away from suppliers, using very expensive equipment. Hence the three most common mining problems are, what does my ore body look like and how can it best be mined, how can I get sup- plies to my mine in the most cost effective way, and how do I control the vast dollars required to keep it all operating. Mincom started life by providing technical mining software to address the first of these problems and was very successful, particularly in the coal mining industry. However the company soon realized that if it was to become a significant provider of mining industry software it must also address the other major problem areas. Hence started what is now Mincom's largest business which is the provision of fully integrated mine management software with strong emphasis on materials and maintenance management to control costs. Mincom not only supplies the software but also provides a comprehensive implementation package using its own staff of experienced mining industry specialists. This papaer highlights some of Mincom's international implementation experiences.

Jan 1, 1989

By T. D. Rourke, E. J. Cording, O&apos

INTRODUCTION Detailed investigation of a 60-ft-deep excavation in a mixed profile of sands and stiff clay was performed by the University of Illinois for the Washington Metropolitan Area Transit Authority (METRO). The work was coordinated through DeLeuw, Cather and Co., the General Engineering Consultant of METRO. Instrumentation was concentrated in a portion of braced excavation for the Gallery Place Station near the intersection of 7th and G Street. The early construction date, the 60 ft depth of cut, and the proximity of large buildings formed the basis for selection of this site as the focal point of observation and measurement. A history of lateral and vertical displacement is provided wherein movements which occurred during excavation to the full depth of cut and, subsequently, during station construction and the removal of braces are described in detail. Observations of preloading and the consequent brace loads and wall displacements are described. The effect of temperature change on brace loads is discussed and the measured apparent earth pressure for the 60-ft cut is provided. The paper discusses the relationship of lateral displacements of the cut wall to the construction procedure, and compares the lateral wall displacement with both lateral and vertical movement in the surrounding soil mass. Based on observed movement, the method by which displacement was predicted for a nearby 82-ft-deep excavation is described. The performance of the 82-ft-deep excavation has been summarized elsewhere (2).

Jan 1, 1974

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By K. L. Branham, D. W. Steeples

Surface collapse over abandoned sub- surface coal mines continues to be a problem in many parts of the world. High-resolution P-wave reflection seismology was successfully used to locate water-filled cavities in a 1-m (3-ft) thick coal seam at depths of 9 m (29 ft) in southeastern Kansas. A dominant frequency of 275 Hz was attained enabling us to delineate the top of the coal seam. To our knowledge, this study is one of the first to locate water-filled coal mine cavities at depths of less than 30 m (100 ft) wing high-resolution P-wave seismic reflection techniques.

Jan 1, 1987

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By Dan Kump

This paper provides an overview of Barrick Gold's Bullfrog underground mine backfill program. The Bullfrog underground mine was a gold mine that primarily used the underhand cut-and-fill mining method. The first portal was established June 18, 1991, and mining continued until Dec. 29, 1998. This paper begins with a discussion of the events that took place to reach about 1.8 kt/d (2,000 stpd) of backfill. It ends with a commentary of what was learned. The Bullfrog experience suggests that there are two essential factors to a successful backfill program: a well-graded aggregate supply and proper placing procedures.

Jan 1, 2002

By B. Elevli

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value (NPV) and overall economic feasibility of a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. The current practice for doing is to do it by hand on the basis of trial and error analysis. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm is developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application on a gold deposit. The results coming from a case study show that the schedules based on the new method provides improved cash flows compare to a manually done production schedules.

Jan 1, 1989

By Randy Ynchausti

ERIC GUTIERREZ, Knowledgescape: Our next speaker is Randy Ynchausti. He's the director of development, Knowledgescape systems division, of EIMCO Process Equip- ment Company. The title of Randy's talk is "An Expert Control System for Phosphate Beneficiation." RANDY YNCHAUSTI: System integration. How does the systems integrator survive when caught between plant engineers, plant management, and third-party engineering firms, and stay within the budget of the corporate goals? I'm not sure that anyone knows how to do all of that on one project. Results are critical when we talk about how systems integrators work with operating people, how the operating people want systems integrators to work with them, and how both groups work together so that at the end of a project, you have been provided with solutions that meet your needs and solve your problems at a fair price. How does the integrator's role change when working with different types of professionals, such as plant managers, plant engineers, engineering firms, or other system integrators? Finally, what is the dynamics of people working with machines and providing services and solving needs? The average number of employees per pound of copper processed has decreased significantly during the past 15 years. I would dare to generalize and say that the average number of employees per whatever unit of measure we have in whatever industry we work in has decreased over the last 15 years. From a system integrator's perspective, there are some clients who lack a bit of internal expertise as corporate downsizing occurs, and that's one reason why we go out to system integrators or third-party vendors and buy things from them to solve our problems. Downsizing really amounts to savings, but more than that, I think Brian expressed this and I agree with him, it also amounts to a cost. Unfortunately, most of us count the savings and none of us count the cost in that approach. It's easy to count the savings, which is one reason why we count it so quickly. Maybe that also accounts for why we set our pencils down so quickly after we get that dollar value. Maybe we should pick that pencil up every once in awhile and refigure the expense, the cost to us, and determine what we're going to pay during the next year or two or three in losing that expense, or that staff. A broad experience base accumulated over projects at various plants helps system integrators to provide services to clients. This experience enables the system integrator to

Jan 1, 1998

By Norman Weiss

The purpose of this paper is to relate progress in the engineering field called Minerals Beneficiation to undergraduate and graduate education in our colleges and universities. So mach has been written recently about the education of scientists and engineers that I've had to struggle against the temptation to repeat what has been often said before, particularly because man like Robert Mehl of Carnegie Tech, Antoine Gaudin of MIT, H. M. Davis of Penn State, and John Vanderwilt of Colorado School of Mines have recently written many quotable paragraphs on the subject. In the matter of progress, the rapidity of proliferation in the area of physical and chemical beneficiation is convincing proof that this is indeed a lively art, and having been a millman for 35 uninterrupted years I prefer to lean on personal observations to some extent, rather than on statistics and charts v culled from the journals. I propose in this paper to talk first about the progress we've made in our branch of the mining industry in the last 3 decades--particularly in the last few years--and try to show that future progress will depend upon the quality of education and capacity for research possessed by our colleges. The second part will deal with some of the problems the colleges encounter in trying to fulfill these responsibilities.

Jan 1, 1959

By A. Mai, J. S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7-m diam primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1987

By Jozef S. Stachulak

Inco Limited operates 11 underground mines in the Sudbury District. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55,000 tons per day. Over 40 surface fans have been installed since the late 1960's. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30 years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 to 330 (cubic metres per second), with motors from 100 to 2500 hp. Fans of the axial flow type have been in common use for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages. The surface area taken up by a typical vertical fan installation is generally about one quarter of that with a horizontal fan of the same capacity. (1) This is not a problem with isolated fans and flat surface outcrop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly favour vertical fans. MAIN FANS INSTALLED There are 43 main surface fans in operation at 11 mines. Twenty-seven of these fans are supply units, and 75% of them are vertical installation. The remaining 16 units are main surface exhaust fans, with predominantly horizontal installation. Within the last five years, some 20 main booster fans have been installed underground at several mines. Axial flow fans, with adjustable pitch blades, are used for both surface and underground installations. Exhaust fans are equipped with stainless steel or cast aluminum blades. Main underground fans are arranged horizontally and the majority of them have a floating shaft between the fan shaft and the motor. (2) The size of the fans in service varies from 1.8 m to 5 m in diameter, with the majority ranging from 1.8 to 2.5 m. The pressure produced by these fans varies from 0.25 kPa to 2.0 kPa. At Inco Limited, two main fans in parallel are preferred, rather than a single fan, so that if one fan fails, the remaining fan can still supply up to 70% of normal air quantities, while the damaged fan is repaired. This requires closure doors on each of the fans so the fan can be isolated in case of failure. It is more expensive than a single fan, but results in less production interruptions. The fan installations are well away from sharp inlet and outlet bends. FAN DESIGN INTEGRITY Both the mine operator and the fan manufacturer must understand that the main fan is critical to the mine operation, and that everything technically possible must be done in design and manufacture to ensure the highest degree of reliability. Some of the design parameters and criteria, based on Inco experience, are outlined and discussed below. RESONANT FREQUENCIES AND HOUSING MODEL ANALYSIS Any fan assembly will have many different resonant frequencies. It is a challenge to the designer to arrive at a design in which forcing frequencies do not coincide with any of these resonant frequencies to produce unacceptable vibration levels in operation. Finite element analysis is a useful tool that can be used to identify the most critical of these, so that housing and blade stiffness can be adjusted to change any resonances that might be close to forcing frequencies. Shaft critical speeds should be at least 25% above the fan operating speed, and there should be sufficient separation between other resonant and forcing frequencies to avoid excitation that might result in high vibration levels. QUALITY ASSURANCE Radiographic Blade Examination Mine fan blades are normally cast in small lots. To ensure that the castings are sound, a full radiographic examination is recommended in the highly stressed lower 1/3 of the blade.

Jan 1, 1995