Search Documents

By Jamie Bonner, Ray Hutton, Taro Nonaka

The Nancy Creek Tunnel is a deep tunnel, designed to store and convey wastewater by diverting flows from trunk sewers currently at or near capacity in the northwest of the City of Atlanta. The tunnel, constructed in hard rock, has an overall length of 13,300 m (43,700 ft), and a finished diameter of 4.9 m (16 ft). The project is currently under construction by a joint venture of Obayashi/CJB for the City’s Department of Watershed Management. This paper describes the contractor’s techniques and equipment, as well as discussing challenges which were overcome. The project is scheduled to be complete in October 2005.

Jan 1, 2005

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

Keeping an eye on the future while honoring the past, Frank McAllister, chief executive officer of Stillwater Mining Co., and life member of the National Mining Hall of Fame and Museum, gave the keynote address to a packed house during the 23rd National Mining Hall of Fame and Museum Banquet in Leadville, CO on Sept. 11. McAllister?s company made news just days before the induction ceremony, when it was announced that Stillwater Mining would acquire Marathon PGM Corp. for $118 million (ME, Oct. page 14).

Jan 1, 2010

By Michael L. Ogilvie

The proportion of underground coal production as a percentage of overall Australian production has fallen in the last 10 years, with underground production remaining more or less static at about 53 Mt (58 million st). However, underground coal mining remains a viable industry in Australia, due to use of modern longwall mining systems. In 1993-1994, 26 longwalls were in operation, with total production exceeding 39 Mt/a (43 million stpy). Some of these longwalls achieve productivity levels approaching efficient opencut operations, and in some cases, they exceed them. These high-production longwall mines are not without problems when depth and distances from outcrop increase and the gas content of the seams approaches or exceeds critical limits. When gas content of a coal seam exceeds 6 m3/t (233 cu ft/st), gas flows into the mine may be sufficient to interrupt production from time to time.

Jan 1, 1995

Microorganisms are finding more use in the mineral industry, with extensive research efforts being reported in 1991. Most of these research efforts were presented in two major meetings, the SME Annual Meeting in Denver (February, 1991) and the Engineering Foundation Conference about Mineral Bioprocessing in Santa Barbara (June 1991). In addition, several articles were published in the IMM Transactions, Minerals and Metallurgical Processing and Water, Air. and Solid Pollution Journal. The literature can be categorized as: • Review articles presenting an overview of the activities in the use of biotechnology in mineral processing. • Research efforts into genetic manipulation of microorganisms to perform a specified job. • Studies in bioleaching of metals from different types of ores. • Biotreatment of wastes from the mineral industry including acidic mine waters, uranium tailings, cyanide destruction, etc. • Investigations into the role of microorganisms in the energy materials, such as oil, coal, tar sands, oil shales, etc. Smith (Mineral Bioprocessing Conference) presented a review of research efforts as well as practical applications of biotechnology in the mineral industry. In another article, Smith et al. (Minerals Engineering) emphasized that extensive fundamentals and applied research work should be pursued to explore the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering.

Jan 1, 1992

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

Because of its small interburden thickness, concentrated stress distributions, high coal seam metamorphism, and complex geological conditions, mining the five coal seams (Nos. 5, 7, 8, 9 and 12) of Kaiping coalfield is difficult. Kaiping coalfield is located within 80 m in the Kailuan Group. The overburden caving caused by mining the five coals seams was measured using ZTR12 geological penetration radar (GPR) survey combined with borehole observations. The development characteristics of full-cover rock fractures after mining were obtained from the GPR scan, which provides a measurement basis for the control of rock strata in close multiple-seam coal mining. For the first time, it was found that the overburden caving pattern shows a periodic triangular caved characteristic. Furthermore, it is proposed that an upright triangular collapsed rock pile and an inverted triangular area with larger fragments piled up alternately appear in the lower gob. The research results show that the roof structure formed in the gob area can support the key overlying strata, which is beneficial to ensure the integrity and stability of the upper coal seams in multiple-seam mining of close-coal seams.

Jan 7, 2020

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By Kira Mizell, James R. Hein, Tracy Conrad

"The Ninetyeast Ridge (NER) extends roughly N-S as a topographic feature for 5000 km, from 31° south to 10° north (Fig. 1) where it becomes buried beneath the Bengal Fan at its northern end. These two geographic characteristics make the NER an ideal natural laboratory for determining the influence of latitude and terrestrial input to ferromanganese (Fe-Mn) crust formation and composition. In addition to study of geographic controls on crust composition, the NER is the largest feature in the Indian Ocean that may host crusts of economic interest.Crusts were collected from 9 of 33 dredge sites from 1.4° north to 26° south latitudes during the 2007 R.V. Roger Revelle Knox06 cruise. Nineteen samples were analyzed for 69 elements each. Nine bulk crusts and 10 layers from four crusts were analyzed. Three of the crusts sub-sampled for layers did not have the bulk crust analyzed and the weighted means for those layers were calculated to obtain bulk compositions. One sample was left out of the statistical analyses because it is phosphatized and chemically quite different from the other samples (Table 1).In order to determine changes in composition with latitude, Pearson product-moment correlation coefficients were calculated for the chemical dataset and latitude of dredge sites, as well as water depth. At the 95-99% confidence level, the following elements increase in crusts moving north along the NER: Mg, Ti, S, Cd, Ni, Tl, Mn, Ba, Co, Cu, In, Li, and Zn; and the following elements decrease northward: Fe, Fe/Mn, P, As, Sc, the rare earth elements plus yttrium (REY), Bi, Ge, and Pb. These correlations indicate that the iron oxyhydroxide component and its associated elements are more prevalent to the south, and the manganese-oxide phase and associated elements increase toward the north end of the NER. This change occurs between dredges D20 and D14 (Fig. 1), with crusts from D20 and south having Fe/Mn !1.0 and those north of D20 ""1.2, with the exception of the phosphatized crust. Crust composition also changes with water depth: Th, Ge, Pb, and the middle rare earth elements (REEs) increase with increasing water depth. Thorium commonly increases in deeper water crusts, which explains the higher Th concentrations in Atlantic and Indian ocean crusts in general compared with Pacific crusts (Fig. 2 and Hein et al., 2012), including the samples analyzed here with a mean water depth of 3584 m. However, water depth does not explain the latitudinal changes because the mean water depths of samples along the northern and southern segments of the NER are roughly comparable. Surprisingly, Si and Al, representing the aluminosilicate/detrital phase, do not correlate with latitude; that is as the ridge approaches and is buried by the Bengal Fan the Si and Al contents do not increase. However, overall, Si and Al have higher concentrations in NER crusts than in central Pacific crusts. Ba can be used as a proxy for primary productivity and statistically does increase to the north along the ridge in the direction of the equatorial zone of high biological productivity. Correlations of Mg, Li, and Zn with latitude may also reflect increased primary productivity at lower latitudes."

Sep 1, 2014

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004

By R. A. Pyper, J. L. Hendrix

Laboratory leaching experiments were conducted to ascertain the effectiveness of acidic solutions of thiourea, CS(NH2)2, for dissolving gold from finely disseminated gold ores. The ore tested was from the Chipmunk ore body of the Northumberland mining district in Nye County, Nevada, USA. Extractions of up to 90% were attained from the ore. Extraction was shown to be dependent on thiourea concentration, ferric sulfate oxidant concentration, acid concentration, and leaching time. Optimum conditions were an ambient temperature leach near pH 1.0 utilizing 100 to 200 kg/ton thiourea and 50 kg/ton ferric sulfate for 8 to 24 hours.

Jan 1, 1981

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024