Search Documents

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By N. E. Green, W. E. Bennett, G. P. Harrison

INTRODUCTION The art of raise boring has seen rapid development and use in underground mines both for primary development and production during the past 10 years. The intensive full scale tests by a major mining company in the Precambrian rocks of the Sudbury district of Ontario, Canada, have lead the way to the general acceptance of the raise drills. The rock successfully raise bored in the Sudbury area has compressive strengths varying from 30,000 to 50,000 p.s.i. As a result of the intensive study, it became evident to many mining companies that raise boring could be adapted to many mining systems. Many companies have modified their planned mining methods to incorporate raise boring. The result has been a more rapid development of their mine and naturally, an economic advantage to them. In conjunction with the acceptance of the raise drills, the range of equipment has broadened in terms of size, capability and efficiency. The concept of raise drilling and the general arrangement of the equipment has seen little change. At some locations there have been reported successes of drilling pilot holes up

Jan 1, 1997

By Carl H. Eckert, James P. Berson

INTRODUCTION The demand for specialty metals in industrial applications is in it's healthiest state since the late 1970'8, and several specific markets are recording record sales. Such metals as gold, silver, zirconim., titanium, beryllium, gallium, germanium, the platinum group, and the lanthanides accounted for sales in excess of $2 billion in 1985 among the end uses covered in this report. Although specialty metals as a group have suffered the effects of recessionary pressures in the past, these metals have proved more resiliant than such large volume metals as copper and nickel. This is due to the unique physical properties they possess which makes the threat of substitution or replacement through technological development uneconomic. The outlook for these specialty metals is optimistic in electronics, catalysts, ceramics, and alloys, and their specialty status results .in a combined average annual growth in demand of 7% through 1990. WHAT MAKES THESE METALS SPECIAL? Such characteristics as electrical conductivity, corrosion resistance, catalytic activity, thermal stability, and optical properties allow the term specialty to be applied to these metals. More importantly, all of these metals possess more than one of these qualities, as shown in Table 1. [ ] These five major functions are important in the end uses for these metals, although the specific applications vary somewhat. Conductivity in term of low or high electrical resistance is of obvious importance to electronics manufacturers. Producers of circuit boards or semiconductors require such metals as gold, palladium, platinum, and gallium due to their low electrical resistivity. However, these producers also require such metals as beryllium in the oxide form for insulation components because of the compound's low electrical conductivity. Although the lanthanides' conductive characteristics are not particularly attractive in electronics, they are of great importance to alloy manufacturers producing permanent magnets for automotive and computer applications. Corrosion and wear resistant properties are extremely attractive to a number of end-use industries, particularly in view of the estimate by the United States Bureau of Mines that $10 to $50 billion in losses are experienced by U.S. industry due to equipment corrosion and $100 billion due to equipment wear. The strength of high purity titanium and zirconium make these metals the obvious choice for corrosion and wear resistance particularly in the chemical processing industry, where the ability to maintain integrity in corrosive environments is a must. Heat exchangers, nuclear control rods, and a number of parts in jet engines have benefited greatly from the use of these metals. However, such other specialty metals as beryllium, and the lanthanides also improve the wear or corrosion resistance in various products. For example, a beryllium-copper alloy contact maintains it's spring like character, and does not loose this character after repeated use, which could result in the loss of an electrical contact. Lanthanide, in the form of cerium oxide, is commonly employed in alloys used to produce catalytic converter casings for the purpose of reducing damage by corrosive road salt. In some instances, the catalytic activity of several of the specialty metals assists in the economic production of other materials. However, the importance of specialty metals in catalysts is most apparent in catalytic converters for emission control. Platinum, palladium, and rhodium are

Jan 1, 1986

By Steven J. Stokowski, Frederick M. Bodycomb

This chapter deals with the use of industrial minerals in insulating materials used to control our thermal and acoustical environment. There are numerous products on the market used for thermal and acoustical insulation; they consume substantial quantities of a variety of industrial minerals. Following is a brief review of the theory and function of insulating materials. Acoustics is the science of sound, and architectural acoustics deals with sound in buildings. If this definition is broadened to include transportation vehicles, it is this end use for which acoustical insulations are primarily manufactured. Sound is defined as the auditory sensation in the ear, or the disturbance in a medium which causes this sensation. Acoustical insulation is used to reduce or eliminate noise, defined as unwanted sound. Noise control may be accomplished by the reduction of sound radiation at the source, by utilizing sound reducing construction methods such as staggered studs, etc., to control sound transmission, or by using sound absorbing material on walls, ceilings, and floors (Rossing, 1985). Acoustical insulation functions by absorbing the energy in sound waves in a porous material. As the sound waves penetrate the pores, they are dissipated by reducing the amplitude of vibration of the air molecules by contact with the pore walls, with subsequent conversion of the sound energy to heat energy. Acoustical insulation is generally highly porous, 1.3 cm or greater in thickness, and has interconnected pores. Acoustical insulating materials include fibrous vegetable or mineral matter and cellular organic and inorganic material, such as natural or manufactured foams (Sabine and Moulder, 1979). Acoustical materials are most commonly porous boards and tiles, which are often composite materials with perforated facing. Roof insulation board and lightweight concrete can also contribute to the absorption of noise. Thermal insulation is defined as material used to control the flow of heat. It may be used for heat control from low cryogenic temperatures (below -100°C) to in excess of 2 200°C for applications such as ablative shields for spacecraft. Heat transfer occurs by conduction, convection, or radiation. Conduction is the transfer of heat without the movement of the conducting medium, as through a metal. Heat convection through a liquid or gas takes place by movement of the medium. Forced convection is the basis for heating and cooling equipment, utilizing pumps or blowers to transfer the thermally conditioned fluid. Free or natural convection occurs due to density differences in the fluid. Radiation is the transfer of energy in space (Eckert, 1985). Conduction of heat through a solid is reduced by insulating the body with foams, or fibrous or small celled granular material. Heat transfer through a gas (convection) is controlled by creating many small pores which inhibit the movement of the fluid, substituting a gas of low thermal conductivity, or evacuating the space. Heat radiation can be reduced by the use of materials that reflect or absorb the energy (Glaser, 1967). Thermal insulating materials may be vegetable or mineral fibers, organic or inorganic particles, or foams with small pores, generally used to form a low density thermal barrier. They may be blocks, poured lightweight cementitious materials, bricks, etc.

Jan 1, 1994

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By David J. Kruse

Although it may be perfectly acceptable to neglect the belt's elastic behavior for many conveyor designs, this can lead to disastrous consequences for others. So how can a designer know in advance if a dynamic analysis is required? Unfortunately, in many cases it is impossible to foresee or predict dynamic problems prior to performing the actual analysis. However, a basic understanding of the principles of conveyor dynamics, as well as knowledge regarding common problem areas, can significantly help the designer make more educated decisions during the initial design stage. This paper will demonstrate how static calculations alone can incorrectly represent the true behavior of the conveyor system. It will also discuss the importance of correctly sizing and locating the take-up system to provide the most economical conveyor design. The use of capstans will also be discussed followed by two examples demonstrating their proper operation.

Jan 1, 2002

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By Joe W. Cotton, Thomas A. Wheeler

This paper briefly covers theories behind caking of crystalline salt particles, and methods of its prevention. The main factors that influence the extent of caking are humidity, storage pressure, temperature variations, and length of storage time. Careful adherence to control- ling these variables are more critical than the addition of even the most efficient anticaking reagent. The principle characteristics that a successful anticaking reagent must possess are: high retention at the temperature of application, good coating of reagent on the particle surface, capability of in- creasing the hydrophobicity of the particle, reducing the surface tension of liquids, and/or creating of a barrier between particles that prevent contact between particles, and modifying the crystal structure of the salt between the particles. Methods to evaluate the reduction of caking tenacity with the application of various anticaking reagents, reagent volatility and reagent degradation in plant and laboratory scales are discussed. Various types of anticake reagents used today in industry are organic active and inactive reagents, inorganic inert and inorganic salt crystal modifying re- agents.

Jan 1, 1986

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993

By G. Sciocchetti, G. F. Clemente, F. Scacco

INTRODUCTION Radon, thoron and their airborne daughter products may result in a significant biological hazard when they are concentrated in enclosed places such as mines, houses and caves. High concentrations of radon and its particulate daughter have long, been known to be a causative agent for lung cancer to uranium miner: (Archer 1973). More recently increasing concern has been expressed on the possible health hazards associated with long term exposures over large population groups to low levels of radon daughters (Cohen 1980, Stranden 1980). Due to its peculiar geological features, Italy has various natural environments where the content of uranium and thorium in the soil may increase underground radioactivity. The presence in Italy of many underground waters rich in radon may be considered a further important source of radon in underground mines. A preliminary survey of the radon and radon daughter air concentrations in italian underground mines was started in 1971 (Bottino 1973). Furthermore many studies (Sciocchetti 1978, Sciocchetti 1980, Clemente 1980) have been performed during the last ten year to characterize the natural radiation environment in Italy. It has been also demonstrated that 21OPb/21OPo skeletal burden in spa workers and non-uranium miners can be heavily increased by the exposure (short or/and prolonged) to high levels of radon daughter air concentration (Clemente 1980). All these studies have been of great help to put in the right prospective the radiation hazards linked to the underground working activity in non-uranium italian mines. Two main actions have been prosecuted from 1971 until today in order to evaluate in greater detail such radiation hazards and then, when needed, to obtain their reduction to levels which may be considered acceptable. The two actions may schematically described as the following: - Measurement of the radon and daughter (and thoron and daughter when needed) concentrations in most of the italian non-uranium mines. The assessment of the radiation hazards linked to both the annual average lung exposure and the 210 Pb - 210 Po annual average dose to the skeleton is then performed for each considered mine by taking into account the main parameters characteristic of the mine. - Set up of a national regulatory recommendation on the permissible limits for the radiation exposure of workers due to underground mining activity. Such recommendation have been established in 1978 and have been designed in order to implement a national radiation protection practice during the underground mining activity. In this paper a summary description of the results obtained during the execution of these two actions will be given. MATERIAL AND METHODS Measurement of Radon, Thoron and their Daughter Products The excution of the planned survey requires the availability of specific techniques and instruments for measuring the different parameters characterizing the radon, thoron and their daughter exposure in mines. A reference laboratory was set up for the development and the standardization of the measurement procedures. Measurements of radon, thoron and daughter concentrations are performed by various methods: instanteneous or grab sampling methods and continuous read out monitors. The radon concentration is usually measured by a modified version of the two filter method. Mine air is drawn into a polyethylene bag and the sample is there after injected into a two filter tube; after sampling the exit filter is counted by the alpha spectrometric technique. The measurements is completed in a total time of less than 25 minutes at a sensitivity level as low as 3.7 Bq/m3 for a tube volume of 15 1. The measurement of radon and thoron daughter concentration and of the relevant potential alpha energy concentration is performed by means of a portable spectrometric apparatus which was developed at our laboratory (Sciocchetti 1981). The device allows multiple operating modes: instantaneous or brief sampling period and automatic cycles; computer data processing is then provided. The instruments that measure continuously radon concentration over long periods of time are of two types: a continuous scintillation monitor and an automated two filter

Jan 1, 1981

By D. Greene

The close integration of mine planning and mine operation continues to be the goal of mine operators. Depending upon the complexity, size and sophistication of the mine, limited success has been achieved in this area. Despite tremendous strides in the development of computer-aided mine planning, digital plans must usually be converted to error-prone paper maps and physical ground surveys for actual excavation and reclamation. However, advances in global positioning systems (GPSs), operator displays and mobile computers now enable equipment operators to work directly from on-board digital plans. A computer-aided earthmoving system (CAES) offers reduced survey costs, faster field transition time and improved excavation accuracy, coupled with faster, more informed decision making regarding key mining operations.

Jan 1, 2000

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

By M. Di Tommaso

Acid Mine Drainage (AMD) is a quite diffuse environmental problem in dismissed sulphur mine districts. AMD is related to sulphur oxidation of abandoned tailings, generating heavy metal-bearing streams with high iron and sulphate contents and low pH. Treatments of AMD aim firstly to increase the pH to reduce its leaching power causing the further release and mobilization of heavy metals through soil solution and groundwaters. Increasing the pH also allows the precipitation of iron (III) (involved in sulphur oxidation and then in AMD generation) and the partial removal of other toxic components such as arsenic. pH adjustment and the reduction of the high concentration of iron are also necessary for the successive biological treatment in permeable reactive barriers (PRB) with sulphate reducing bacteria (SRB) (II step, biologically mediated precipitaton/biosorption) to avoid the rapid plugging of the barrier (for the large amounts of iron precipitates) and to ensure neutral pH conditions for SRB growth. In this work the first step (chemical precipitation) of a combined chemical and biological treatment of AMD is presented. Experimental data from column tests using carbonate stones to remove iron and increase pH were reported. Toxicity tests have been carried out on the treated wastewaters by Lepidium sativum.

Jan 1, 2006

By V. R. Degner

Comments Summary It is very interesting to review the technical changes which have occurred in the industrial practice of minerals flotation over the past two decades. In 1972, worldwide industrial flotation was dominated by 'mechanical' flotation machines having an individual cell volume less than 500 cu.ft. Manufactures, such as DENVER Eqpt. Co., OUTOKUMPU, WEMCO, GALIGHER (AGITAIR), AKKER, and later DORR-OLIVER, produced flotation machines featuring a mechanical rotating impeller which served to mix pulp and air, prior to flotation, and to keep the solid ore particles in suspension. While sharing this common mechanical impeller feature, the machine design of the various manufactures differed in detail; particularly in regard to the vertical location of the impeller in the cell and the means by which flotation air was brought into contact with the pulp within the rotor mechanism. A review of the existing technical literature in 1972 would identify academic research studies, particularly at Columbia University (N. Arbiter, C, Harris ...) aimed at comparing flotation cell design concepts, of the various machine manufactures, on a hydrodynamic basis. These research studies were confined to very small, laboratory bench size, flotation machines, and the benefits of incorporating hydrodynamic considerations in the scale-up of the existing 300 cu.ft. mechanical flotation technology to larger cells was not commonly practiced industrially. Technological advances in minerals flotation, over the past two decades, have been influenced by a variety of economic factors including the increasing development of lower grade ore bodies, the attractions of producing a higher grade final concentrate, and the economy of tails retreatment to improve overall plant recovery performance, and flotation system “optimization" became increasingly important through the 1970-80 time period. The trend toward processing lower grade ores led to higher tonnage mill operations, and stimulated the development of the very large capacity mechanical flotation machine for roughing and scavenging duty. In 1972, the 500 cu.ft. size flotation machine was being pilot tested and introduced to the industrial market. Today, 1993, individual cell volumes of 1500-3000 cu.ft. are operating successfully throughout the world, and well planned plant test programs have concluded that the very large flotation machine can achieve the same metallurgical performance level of its smaller predecessor. The large flotation machine development record clearly credits the incorporation of internal cell hydrodynamic considerations in guiding the scale-up of the mechanical flotation machine to large sizes. This guidance eliminated, or reduced significantly, costly in-plant prototype machine changes which increase Dramatically with increasing flotation machine size. Early in the 1980's, at approximately the time that flotation machines in the 1500 cu.ft. class were being introduced into the market, it became evident that the availability of the very large mechanical flotation machine brought with it the need for a systematic means to "optimize" the flotation system by relating flotation cell size, row length (i.e. number of cells per row), and flotation rougher, scavenger, and cleaner system configuration to the economic objectives of the concentrators' operating management. Flotation system optimization consists of quantifying the flotation process performance using a suitable model which relates the kinetic response of the trace specie and the gangue material to the cell overflow, and produces a numerical relationship between product grade and value recovery. The computer analysis technique has proven to be an invaluable tool in determining the kinetic model coefficients which characterize a given application, and is also used to apply the resulting model to a proposed minerals beneficiation situation seeking to "optimize" the flotation system by relating metallurgical grade-recovery performance, flotation cell size, and circuit arrangement, to plant space, installation, and operating costs. It is interesting to note that these same computer based kinetic flotation analysis techniques can be easily applied to quantitatively evaluate the effect of different chemical reagent strategies, and flotation air transfer, on process performance for a variety of candidate feed ore types.

Jan 1, 1993

By V. A. Evans, D. L. Hellier

Introduction Preparing a report on fluorspar economics in the US could have been somewhat complicated at one time. This was because the number of producers, both large and small, derived production from different locations through-out the western US and the southern Illinois and western Kentucky fluorspar districts. Companies, such as Allied Chemical and Williamson Mining, operated in the Jamestown district of Colorado. In Walden and Salida, CO, the Colorado Fluorspar Co. operated mines and mills. In New Mexico, both Du Pont and Allied had mines and mills. In the Illinois-Kentucky district, US Steel, Rosiclare Lead and Fluorspar, Minerva Oil Co., and Marathon Oil all produced spar for the US market. Now all of the companies are out of the fluorspar business and, with the closing of the Seaforth Mineral Co.'s Inverness Mining Co., only Ozark-Mahoning Co. survives as a domestic producer. History Ozark-Mahoning Co., as it now exists, was formed in 1946 by the merger of Ozark Chemical Co. and Mahoning Mining Co. Ozark Chemical Co. was started in the 1920s to produce sulfuric acid for two refineries located in Tulsa, OK. Mahoning Mining was originally formed by the founders of Ozark Chemical Co. and the Youngstown Sheet and Tube Co. to produce fluorspar and associated minerals from properties in the southern Illinois and western Kentucky fluorspar district. In 1937, Mahoning Mining started an exploration program, employing contractor-operated churn drills to look for reserves in Hardin and Pope Counties in southern Illinois. Based on known reserves in the area and the results of the exploration program, work was started in the fall of 1938 to build a selective flotation plant at Rosiclare, IL. The mill was completed and put into operation in August of 1939. The company's first mining efforts were in the Cave-In-Rock district just north of Cave-In-Rock, IL. The deposits in this area were of the Manto or bedded type. They have been the mainstay of the company's operations in the Illinois-Kentucky fluorspar district. In 1950-51, the company expanded its operations by purchasing fluorspar properties from Colorado Fluorspar Co. at Walden, CO. This location was operated from 1952 through 1958 and from 1968 through 1973 when it was closed permanently. In 1974, Ozark-Mahoning Co. was purchased by Pennwalt Corp. Presently, it is a wholly-owned subsidiary of that corporation. As the only major domestic producer of fluorspar in the US today, the company's ability to survive under the flood of imported material is directly related to the four major segments of its operations. These are: exploration, mining productivity, maintenance, and marketing. All are done in-house. Exploration The Southern Illinois fluorspar district is located in the most complexly faulted area of the central US. The formations are sedimentary in nature and range in age from Devonian through Pennsylvanian. The deposits are small, they range in size from a few thousand tons up to 900 kt (1 million st), with the average minable deposit being around 544 kt (600,000 st). The ore occurs in both nearly vertical vein deposits and in Manto or flat lying bedded deposits. Due to the relatively small size of the deposits and the depth at which they occur, a good low-cost exploration program is essential to ensure that new finds of ore are equal to the mining extraction rate. Ozark maintains a leased land position in Pope and Hardin Counties that will fluctuate somewhere between a low of 40 km2 (10,000 acres) up to a high of 129 km2 (32,000 acres), depending on total size of tracts leased. Most all lands are obtained through a standard lease purchase option, with a small minimum royalty per acre during the normal 10-year option period. All leases are standard and without deviation to control land cost. All land leasing is done through Ozark's geological staff, who also

Jan 11, 1986

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic application, perlite properties of low density and fine particle size are desirable, while loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including particle size, density, and surface treatment are discussed in relation to the various insulation applications. Also, typical mineral processing and manufacturing techniques are reviewed.

Jan 1, 1987

By Deepak Malhotra

INTORDUCTION Mining operations are unique In that they handle large volumes of water (millions of gallons) daily. The water contains dissolved metals, processing chemicals, organics, and other contaminants, There are several sources of water contamination at mine sites: mines, mills, tailings ponds, and Industrial/utility complexes. Utility waste water generally represents a very small portion of the total process water utilized in a normal milling operation and hence will not be addressed in this paper. Mine drainage can represent a significant amount, thus having an Impact on the recovery of metals, especially In Industrial minerals operations, and may have to be treated separately. The National Pollutant Discharge Elimination System (NPDES) effluent limits are becoming more stringent, thereby requiring mining operations to treat process water prior to discharge to the environment. The general trend Is to move toward a closed-loop waste system and treat only that small fraction of process water which Is to be discharged to public lands. The following section discusses the reasons for waste water treatment and the existing and emerging technologies for meeting NPDES effluent limits. REASONS FOR WATER TREATMENT Due to the diverse nature of the mineral Industry, process/waste water contamination problems as well as processing flowsheets are site specific. However, certain generalizations can be made specific to processing of different minerals: • Acid mine drainage Is a problem at sulfide/coal mines. • Cyanide contamination of water Is a problem at gold processing plants. • Organics can be a problem at mines using flotation oils. • Tolling ponds are generally acidic at sites processing industrial minerals such as silica sand and feldspar. The cost for water treatment Is viewed as an added cost of production. Hence, large mines are moving toward dedicating personnel to management of water resources in order to minimize waste water for treatment. Very often, mines having closed-loop water systems will treat waste water for reasons other than meeting NPDES regulations. These Include situations where process requirements dictate use of high-quality water for separation of minerals, neutralization of acid mine drainage water, and portable water for the mill. WATER TREATMENT TECHNOLOGIES Water treatment process has to be cheap and simple because It has to process large volume, and It does not directly add to the bottom line, namely revenue. The water treatment process development has to be site specific because the contaminants In the water vary from site to site. and discharge limits for water vary from state to state. The current technologies for wastewater treatment have been divided Into the following three areas: • Removal of heavy metals • Cyanide destruction • Scale control A brief summary of the current technology In each area Is discussed below. Removal of Heavy Metals The physical and chemical processes for heavy metal removal are summarized in Table 1. The most common and cheapest approach has been the precipitation of hydroxides at high pH followed by sedimentation and thickening of solids. The remaining solids can be removed by filtration. The pH is adjusted back to neutral, and the water Is discharged. This process is most commonly used wastewater treatment technology in the mining industry. The basic processes can be modified by combining other operations in order to meet the objectives of the specific site as illustrated In the following examples: • AMAX's Mt. Emmons treatment facility uses Lectro Clear® process where the precipitated solids are removed by electroflotation. • AMAX's Climax Mine water treatment plant used Ion exchange columns to meet the discharge limits on molybdenum.

Jan 1, 1992

Coal fly ash and flue gas desulfurization (FGD) sludges can be returned to mine pits, fills and revegetation zones in Virginia by regulation if (and only if) a positive beneficial use can be shown. Utilization of alkaline fly ash for control of acid drainage from pyritic coal processing waste piles, and use as a soil amendment for revegetation, are the two dominant beneficial uses proposed over time. Both applications must be controlled by the basic chemical properties of the ash proposed for utilization. Currently, public concerns over long-term As and Se leaching from various applications are increasingly driving regulatory options for mine site utilization. Many fly ash materials are relatively low in inherent alkalinity or neutralizing ability, and certain ashes are actually acidic. Failure to add sufficient total alkalinity will result in strong acidification of the ash utilization zones, stripping heavy metals like Mn, Zn and Cu from the fly ash matrix. Similarly, if alkaline ash is loaded into non-acid forming coal wastes at high rates such that leachate pH is > 9.5, significant leaching of As and Se has been documented in large scale laboratory leaching columns. Utilization of fly ash and FGD as a mine soil amendment for revegetation is based upon combined liming and water holding capacity benefits, however, levels of soluble salts (primarily sulfate and borates) limit one-time application rates to 100 Mg/ha or less.

Jan 1, 2006

By Anthony G. Fonseca

About 45% to 50% of the coal mined in the United States passes through coal preparation plants. East of the Mississippi River, this number increases to about 75% to 80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation is an effective process that achieves 75% to 80% ash reduction, 15% to 80% trace element reduction and 85% to 90% Btu recovery. It is less effective for pyrite reduction (35% to 70%) and on-line operating time (40% to 60%). It also suffers from obsolete control systems. In coal preparation, raw coal is modified to a more preferred form to enable its use. The methods used to achieve this modification must be cost-effective and appropriate to the raw coal, the scale of production and the end-user requirements.

Jan 1, 1995

By Kalle Hakalehto

Automation and mechanization in mining has no value of its own. It has to be measured in economic terms or in Increased safety or in the utilization of deposits which otherwise were unavailable. The mechanization and automation of workphases in the mining and rock construction process has led to the decrease of manual work. This has had a very essential importance in the countries where the labor is expensive or where there has been difficulties in the availability of labor. The work has become much more efficient. We would like to argue that the need of mechanization has been initiated mostly from the above mentioned reasons. The origin has seldom been the "process" approach or the real need or will to change the way mining is done. Through mechanization bigger unit sizes of machines and operations have become possible and better efficiency is achieved. This has led to new problems as well, but in most cases they have been solved so that better and more economic outcome than before has been the end result. The changes have thus been justified. It is perhaps feasible to state already at this stage that we see that the mechanization andautomation steps in the difficult conditions of mining have been remarkable. There is not a slightest underestimation of the achievements and importance of this development in our mind. Where we are to- day is the result of the experience, know-how and technological excellency of all the parties involved. The natural approach to automation has been through mechanization and automation of individual unit operations and machines. This has been the way as well in manufacturing industry as in mining. There may not have been any other way. The other presentations in this session tell us very clearly of the approach .which the machine manufacturers have taken. They have not done it alone but 'most of the initiatives have come from them. A good use of their present achievements gives many possibilities to increase the, efficiency in mining. We would, however, like to extend the view one step further to the future:

Jan 1, 1989