Search Documents

By Donald A. Dahlstrom, Soumitro Nagpal, Timothy Oolman

Bacterial oxidation of a pyrite/ arsenopyritic gold-ore concentrate was carried out with continuous flow operation in 14 liter (1.4x10-2 m3) mechanically agitated reactors. 02 and C02 uptakes were determined at varying residence times. Bacterial concentrations were measured using a protein assay. A sharp optimum in biooxidation rates was observed with increasing steady-state residence times. Growth of the bacteria and biooxidation of the mineral were both shown to be strongly dependent on dissolved 02 levels in the liquor.

Jan 1, 1990

By Malcolm J. McPherson, Daniel J. Brunner

This paper describes an experiment conducted to investigate the law of airflow on a mechanized longwall coal face. Background to the Square Law relating frictional pressure drop and airflow is presented and deviations from this Law are discussed. The procedures used to investigate the Law of Airflow for the longwall are described and the results are presented. The results verify the Square Law relationship for airflow along a mechanized longwall face.

Jan 1, 1987

By K. A. Natarajan, M. K. Yelloji Rao

The electrochemistry of sphalerite and chalcopyrite was investigated under both open-circuit and applied potential conditions. Emphasis was placed on the selective dissolution of sphalerite from a mixture of sphalerite-chalcopyrite flotation concentrates as a function of applied potential, acid concentration, pulp density, and time. Morphological studies using a scanning electron microscope (SEM) were also carried out with chemically leached, galvanically leached, and unleached surfaces of sphalerite and chalcopyrite. Selective dissoulution of sphalerite could be achieved if the mixed chalcopyrite-sphalerite concentrate slurry was maintained at a negative applied potential of -0.4V (SCE). Probable mechanisms involved in the selective dissolution of zinc are disscussed.

Jan 1, 1990

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines' acceptance of the technology.

Jan 1, 1991

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992

By Shouci Lu, Sun. Keji

Most phosphate ores in China are characterized by fine dissemination of the intergrown minerals and high content of carbonates. Therefore, in order to recover phosphorus minerals by flotation, some technological problems must be solved, such as fine particle flotation and separation of phosphate from carbonates. For effective flotation of finely ground phosphate ores and selective separation of phosphorus minerals from carbonates, S-series and L339 modifiers have been developed. A series of combined collectors with improved collector ability and selectivity have been developed and applied in several flotation plants in China. In this paper, CCLS, a combined collector for phosphates and PA-31 and a collector for reverse flotation of carbonates, are described. It has been found that some surfactants added with fatty acids function well in flotation at lower temperature, hence heating pulp in winter may be excluded. It is important for energy savings. The synergy mechanism of these additives in fatty acid flotation is discussed in this paper.

Jan 1, 1999

By R. Sripriya, Ch. V. G. K. Murty, N. D. Rao, P. V. T. Rao, A. Ramu

Studies were carried out to improve the performance of hydrocyclones at Tata Steel's chrome ore beneficiation plant in Sukinda, India. The optimal cut point of the hydrocyclones was determined in the laboratory using a stub cyclone. In the tests, the operating and design variables, including spigot diameter, density of feed slurry and inlet pressure, were varied. Subsequently, plant trials were carried out, and attempts were made to develop a model of the hydrocyclone using the Rao, Lynch and Plitt model. The cyclone efficiency was represented by the parti¬tion curve, and the performance was evaluated mathematically from a reduced efficiency curve, represented by the equation:

Jan 1, 2000

By Steve Kral

The Red Dog zinc-lead deposit, said to be the world's second largest, is located inside the Arctic Circle in northwestern Alaska - a location too harsh and remote for some mining companies but just right for Cominco Ltd. The complex has been in operation since November 1989 and is producing 508 kt/a (560,000 stpy) of zinc concentrate, 109 kt/a (120,000 stpy) of leadconcentrate and 45 kt/a (50,000 stpy) of an Imperial Smelter Feed, a combined zinc-lead mixture that is too small to separate. All of this concentrate production derives from a relatively modest mine production of 5.4 kt/ad (6000 stpd) extracted from a surface pit. Despite being a high-grade zinc-lead deposit, Red Dog's metallurgy is complex, requiring a very fine grind and use of column cells for flotation. The Red Dog complex is located in the DeLong Mountains. They are characterized by eight stack and folded thrust blocks that contain sedimentary and igneous rocks. The Red Dog deposit is located in the second lowest thrust and ist hosted by late Mississippian to Permian age black shale, the Ikalukrok member of the Kuna formation. The Red Dog mining complex is operated by Cominco Alaska, Inc., a wholly owned subsidiary of Cominco American, Inc, which, in turn, is owned by Cominco Ltd. In 1980, the deposit region was acquired by NANA Corp. as part of the Native American Claims Act Settlement of 1971. NANA is one of 12 such Native Corporations in Alaska. In 1982, NANA and Cominco American signed a develop¬ment agreement and formed Cominco Alaska to manage the project.

Jan 1, 1992

By M. R. Paterson, M. K. Suddaby

Operational and economic factors tend to favor the application of continuous processes in preference to batch processes in the majority of mineral processing applications. In this paper, the requirement for a continuous elution process is established and the development of a large-scale pilot plant is described. It is based on a continuous elution apparatus that has a number of special features. These are the subject of various patent applications. The apparatus is suitable for adaptation to the AARL, Zadra, and other methods of elution. The performance of the atmospheric continuous elution system (ACE) is concluded to have significant advantages over the batch process.

Jan 1, 1988

By J. S. Long

A finite-difference model using a digital computer was constructed to assist in the water management of a proposed oil-shale mining operation in the Piceance Basin in Colorado. The presence of ground water is both a detriment and a benefit for development of the resource. On one hand, dewatering is required because permeable zones are present in and above the oil-shale sequence, and rich oil shale at the proposed mine is as much as 457 m (1500 ft) below the water table. On the other hand, ground water is the most feasible source of water for processing the oil shale. A ground- water model was constructed to simulate the development of an environmentally acceptable water-management system that will satisfy both the mine-dewatering requirements and the water-supply requirements for processing. The ground-water model discussed in this chapter was constructed for the Rio Blanco Oil Shale Co. (RBOSC) by International Engineering Co., Inc., a subsidiary of Morrison-Knudsen Co. The model was applied to evaluate dewatering and water control systems for several open-pit mining plans initially investigated to develop Federal Lease Tract C-a. A collateral application of the model analyses was to project effects of the proposed dewatering operation on the regional ground-water regime in connection with a permit acquisition program by RBOSC. Subsequently, RBOSC has completely changed its mine development plan and has adopted modeling and related techniques more suitable for study of that plan and dewatering operation. The authors of this chapter are solely responsible for the contents and conclusions.

Jan 1, 1979

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

By J. L. Weaver

The spiraling rate in phosphate rock demand during the period 1957 to 1967 led producers to expect a continuation of a high growth rate. Consequently they expanded production capacity to meet the expected demand. Both the domestic and the world demand has shown little growth over the past three years. Florida producers operating at less than 75% of installed mining capacity, produce all that their markets will absorb. We expect that the nest few years will bring only a slight improvement in this condition. An increased demand in the domestic agricultural market will be partially offset by a continuing erosion in the export market.

Jan 1, 1972

By J. S. Anderson

Size reduction models of cone and impact crushers have been developed using Whiten's generic computational structure for the description of crushers. They incorporate a laboratory single particle breakage test and the t-family of curves to describe the breakage behaviour of the feed ore. A quantitative model of 7-foot cone crushers has been developed, based on surveys of Svedala (Kobe) and Nordberg machines. Survey data on a Canica vertical shaft impact machine have been used to validate the impact crusher model. Given the crusher operating conditions, such as tonnage, feed size, set and liner condition, or rotor speed and radius, plus breakage information on the feed, the models provide good predictions of product size distribution, and appear to be robust over a wide range of conditions. They are incorporated in commercially available computer simulation packages.

Jan 1, 1998

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By Michael L. Nave

An existing coal mine's raw coal 60 inch conveyor system had become productivity bound by a capacity of 3,500 tph. The existing conveyor drives were fixed speed wound rotor induction motor drives installed in 1983. The fast track upgrade installed variable speed medium voltage variable frequency drives to speed up the conveyor to a capacity of 5, 000 tph. The installation took place over a one week system shutdown during Christmas 2000.

Jan 1, 2002

By R. L. Grayson, N. P. Reddy, D. A. Kinzler, S. Yuan, W. R. Myers, R. A. Wells

An examination was conducted on the impact of roof conditions and the mining cycle in determining a representative respirable mass concentration at the mid-shearer location on a longwall panel. Multiple personal gravimetric dust samplers, operated at a flow rate of 2.0 lpm, were used at different locations along the face to isolate the concentrations and variances associated with good and bad roof conditions under both the cutting and cleaning mode of operation. The number of samples needed to estimate the population variance at a given confidence level was analyzed. In addition, the statistical analysis showed that the coefficient of variation of dust concentrations at different locations and under different conditions ranged from 0.185 to 0.475, with an average value of 0.283. The estimates of the average dust concentration for a shift and the variance of the dust concentrations were calculated. A total of 48 data points were available for an [a x b] factorial ANOVA (analysis of variance). The estimates of the variance components were determined. The results from F-tests indicated that both the roof conditions and mining operations had a significant effect on the respirable dust concentration. There was no significant interaction effect between mining operations and roof conditions. In conclusion, this study shows that not only should sampling and analytical errors be considered in determining the required number of samples for a good estimate of the long-range exposures of miners, but also fluctuations of concentrations due to mining operations and geological conditions should be taken into account.

Jan 1, 1991

By Antoni Czubak

It is difficult to simulate properly the vibratory transport. One does not know how to describe the influence of a bulk material layer on the transporting trough. There are few approaches, but none is satisfactory enough. Author proposes to apply a model of a dynamic dumper which simulates periodical collisions between material and the trough, when they are coming to the contact after the free flight of material above the trough. Computer calculates average speed of transported material and handling output as well. When the quantity of material on the trough is known, then the force of the dynamic dumper could be calculated. This force together with the exciting force of the vibrator are introduced into equations describing the model of a mutti- mass conveyor. The basic goal of simulation is to find the required exciting force and the power of an electromagnetic vibrator. it is possible to find optimal data of designed elements of vibratory conveyors as well.

Jan 1, 1996

By E. F. C. Ferrett

The benefits derived from the use of main fan evasees or diffusers are well known. If a well designed evasee is fitted to a fan either more air will flow through it or the same air flow rate will be discharged at a lower fan speed. This latter possibility will reduce the air power requirement of the mine, the fan input power and the overall energy costs. Despite these apparent advantages, many reports have been received from the industry of poor evasee performance. After examination, it appears that these problems are often caused by installation difficulties or inaccurate design procedures. The performance of an evasee is affected by several independent factors. Some of these factors describe the evasee geometry whilst others are concerned with the behaviour of the air as it passes through the evasee. This paper shows that the divergence angle is by no means the only ;important parameter which affects evasee performance and that the size of the inlet boundary layer has a significant influence. The performance of evasees of differing geometric shape are compared and the criterion to be used for optimum performance is discussed. It is shown that the commonly used evasee efficiency is a poor indicator of good performance. Recent work by the author and others is evaluated and a simple design. guide discussed. For more sophisticated work, details of a. computer program are provided. Finally, a brief resume of the performance of truncated diffusers is given. Since compressibility effects can be ignored for most mining applications, incompressible flow has been assumed for most of this paper.

Jan 1, 1980

By B. Elevli, M. D. G. Salamon

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The mine's production schedule defines the distribution of cash flows and, as a result, directly influences the net present value (NPV) and overall economic feasibility of a project. The need to plan and operate a mine with an optimum production schedule has been obvious for some time, but the methods used to obtain such a schedule have not been so obvious. The current practice is to do a trial and error analysis by hand. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm was developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application to a gold deposit. The results of this case study show that the schedules, based on the new method, provide improved cash flows compared to production schedules done manually.

Jan 1, 1992