Search Documents

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By Kenneth J. Reid

The application of computers for control purposes in hydrometallurgical processes is not as well-established as in mineral processing plants. This is not only due to the comparatively new development of large-scale application of hydrometallurgy and the relatively small number of operating plants, but also due to some of the basic dynamic characteristics of hydro- metallurgical processes., Basically there is little difference in the development and application of digital control techniques in hydrometallurgical plants from those techniques widely in use throughout the chemical process industry and in nonslurry applications; particularly for those cases involving liquid streams only, the primary sensing elements are essentially the same. On-stream X-ray fluorescence analysis is a well-established method for determination of metal content in the process streams, and standard equipment is used for the measurement and control of pH, flow, density, temperature, pressure, and other variables. Nevertheless, the high proportion of corrosive slurry streams at elevated temperature and pressure poses a challenge to the instrument engineer concerned with developing long-life, reliable instrumentation. One major difference and potential problem area in developing control systems for hydro- metallurgical processes is related to the very long time constants which are common in the larger plant. In these circumstances, it is important to define the overall control objectives very carefully and be prepared to allow for considerable drift in intermediate variables. In larger projects with many control loops the general advantage of lower costs compared to conventional analog instrumentation can be confidently expected. Also in most cases, the process analysis necessary to design and specify a comprehensive computer control system and the increased operator involvement in implementing digital control systems yield additional benefits due to the increased understanding of the dynamic characteristics of the process.

Jan 1, 1979

By Jack R. Nawrot, R. E. Lounsbury

Preservation and replacement of wetland habitat has become a National priority. Lands affected by mining can provide an excellent opportunity to develop wetlands where none currently exist. This proposed end use for land can require converting quality farm land from its pre-mining farming capability. Where such conversion is necessary, environmental regulatory authorities in lllinois have come to view wetlands among the preferred restoration alternatives. Research and large scale demonstration projects conducted by the Cooperative Wildlife Research Laboratory at Southern lllinois University at Carbondale have shown that coal slurry ponds can be reclaimed to wetlands. Key to successful wetland establishment is recognizing distinct zones in the slurry surface to be vegetated and treating these zones with appropriate soil amendments and plants.

Jan 1, 1991

By Marcelino Cortina

It is known that underground bituminous coal mining in the Central Asturian Coal Basin (North of Spain) is a complicated task, due basically to the difficult geological conditions: thin and steep Seams with many faults and other disturbances. Therefore, it is not easy to decide what is the most suitable mining method for each of the seams, and problems in making the correct decision are encountered frequently. Because selections in the past have been inadequate an Expert System, ASTURLABOR;hulla, has been designed and will be developed' to provide accurate advice in the mining method selection process. The paper describes the major features of this Expert System and outlines the ASTURLABOR general project, which includes five other mining Expert Systems to complement ASTURLABOR-hulla.

Jan 1, 1989

By Jianliang Li, Jan M. Mutmansky

This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels.

Jan 1, 1992

By Wolfgang Sand, Alex Schippers, Tilman Gehrke, Thore Rohwerder, Peter-Georg Jozsa

Metal sulfides are degraded via thiosulfate (pyrite) or via polysulfides and sulfur (sphalerite, galena, chalcopyrite) by leaching bacteria The attack on the crystal lattice is either effected by only iron(III) ions or by iron(III) ions and protons, respectively. Consequently, different endproducts are formed. For a control of ARD-processes, these reactions need to be hown to regulate them. Experiments in percolators up to 65 m3 with inorganic compounds like fluoride, concrete, or SDS resulted in differently lasting inhibition. Microcalorimetric measurements of microbial leach activity allow monitoring of these effects with respect to active bacterial cells, and, in addition, the amount or rate of dissolved metal sulfide allowing prediction of possible endangerment by ARD.

Jan 1, 2000

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

By Clement K. Chase, Manuel Lastra, George M. Potter

Heap leaching for gold-silver recovery in the western United States has been widely applied. Advantages, disadvantages, and requirements of the method are discussed, as well as heap building, recovery systems, agglomeration applications, and safeguards against freezing. A list and review of current heap leach operations world-wide are presented, together with obvious opportunities for application of this innovative technique in new areas.

Jan 1, 1983

By Michael G. Nelson, Hanguang Wu, V. Izaxon, Sukumar Bandopadhyay

The method of mine ventilation involving heated air, which is frequently used in mines in cold regions, does not correspond to the natural conditions prevailing in permafrost regions; it is not economical and leads to a series of complications which can be prevented or greatly reduced by lowering the temperature of the air stream entering the mine until it is equal to or very close to the temperature of the frozen ground This paper presents ventilation design approaches which can be engineered to provide the required micro-climate and thus en- sure the stability bf the ground for placer mines in permafrost. Specifically three ventilation design approaches are presented: 1) design based on minimum thermal impact; 2) design based on positive/negative heat accumulation in the existing mine airways; and 3) design based on heat exchanging devices such as thermosyphons placed above ground.

Jan 1, 1997

By J. DeYoung

Weak demand for metals and consequent low metal prices resulted in continuation of the depressed state of US mineral exploration activity through 1983. Data collected by Resources for the Future Inc. and The Pennsylvania State University for a cooperative study on mineral exploration activity indicate that US exploration in 1983 fell by as much as 25% from 1982 levels. Precious metals remained the focus of most exploration efforts, as gold and silver prices remained attractive compared to base metals. Reports of 1983 domestic exploration and development activities in several industry journals indicates that about 85% to 90% of those projects were directed primarily at gold and silver. Gold exploration included work by several companies on Carlin- type disseminated gold deposits in Nevada, geological prospecting and drilling in the Wenatchee Gold Belt in Washington, and interest in lode and placer gold properties in California, especially by several small Canadian firms. Precious metals exploration projects were also reported in Alaska, Arizona, Colorado, Montana, New Mexico, Oregon, South Dakota, and Utah. There was also tome precious metal exploration activity in the eastern US. Development continued at the Ropes gold mine near Ishpeming, MI, and companies explored historic gold-producing areas in the Southeast. Some exploration for nonprecious metals took place last year. Stratabound copper-silver deposits were examined in western Montana, and US Borax continued exploring molybdenum resources in the Misty Fjords area in Alaska. Work on these projects during 1983 may have been stimulated by time limits on the availability of certain federal lands for exploration more than by projected improvements in metal markets. During 1983, several papers were published on mineral exploration strategies and the future of US exploration. David Watson of Raymond Kaiser Engineers, in a paper presented at the 1983 AMC Mining Convention, forecast increased exploration activity for gold and silver because of world economic conditions. He added that antimony, manganese, chromium, graphite, mercury, tantalum, tin, and barite are also likely targets based on their limited domestic reserve availability. He cited concern over reported subsidized mineral production by foreign producers and US regulatory and land-planning policies as retarding mineral exploration activity. Douglas Cook of Freeport Exploration Co., at the same meeting, presented a paper that showed that a 1950-75 period of vigorous exploration has been followed by a period where acquisition has replaced exploration as the predominant means of acquiring new mineral properties. At a December IIASA conference on "The Economics of Mineral Exploration," in Vienna, Austria, A. Rose and R. Eggert of The Pennsylvania State University pointed out that recent exploration decisions tend to rely more on evaluating production costs and comparing them with existing deposits, rather than on return of

Jan 5, 1984

By C. A. Rowland

Introduction Comminution efficiency, as measured by relating circuit performance to the consumption of energy and the time and money required, can be determined by the following comparisons: Theoretical efficiency: The theoretical efficiency is the actual energy consumed in a comminution machine compared to the theoretical energy required to perform the size reduction. Operating efficiency: The operating efficiency compares the operating work index of a comminution machine to the Bond work index of the ore, as determined from bench-scale crushing and grindability tests or pilot-plant tests. Economic efficiency: The economic efficiency is comparing income from production to predicted income. Key words: Comminution, Bond work index, Grinding, Crushing, Ball mills, Rod Mills. Theoretical efficiency In their book Process Engineering of Size Reduction - Ball Milling, Austin, Klimpel and Luckie (1984) stated that, "We have tried throughout this book to avoid the use of the term grinding efficiency because the degree of conversion of energy to useful size reduction is an ill-defined concept. In addition, the only efficiency, which is of real interest, is the meeting of product specifications at the minimum cost." The National Materials Advisory Board, National Re¬search Council (1981), in the abstract of a report titled "Comminution and Energy Consumption" stated that, "Up to 99% of the energy consumed in grinding these ores may be expended in the movement of machinery, with noise and heat the undesirable byproducts, thus leaving only 1% of the energy available for size reduction. Coupled with this is evidence that many of today's crushing and grinding techniques not only are antiquated but have little or no scientific base of understanding." Throughout the past 50-plus years, grinding efficiency has been referred to as being from 1 % to 10%. The measurable basis for these observations is difficult to establish, but they appear to be based on production performance compared to theoretical energy requirements for the work done. The theoretical energy requirements were determined from the energy required to break a single particle or a thin layer of monosized particles by compression or by a single impact from an impact-testing device. King, Tavaras and Middlemiss (1997), in a paper titled "Establishing the energy efficiency of a ball mill" described such a test. These batch single-breakage tests generally do not duplicate the continuous-breakage process in the comminution machinery used in ore concentrators. Operating efficiency The currently available crushers and grinding mills are fed at a controlled continuous flow rate, and they impart the breakage pattern needed to produce the desired size reduc¬tion. While theoretically inefficient, they are the most practical comminution machines available. The operation of this machinery is relatively simple and can be controlled with available control systems. The essential factors in determining the operating efficiency of comminution machines are energy, as consumed in the machinery, and the required energy, as determined from test work. Bond work indices, obtained from bench-scale or pilot-plant crushability and grindability tests are used in the following Bond equation (Bond, 1960) to determine the energy required to produce the required size reduction

Jan 1, 1999

By S. O. Moshier, L. S. Barron, J. C. Hower

The Hardgrove grindability test, commonly used in coal characterization, was conducted on 13 Mississippian carbonates from Kentucky, Tennessee and Illinois. The results demonstrated that the grindability increases with a decrease in the Si02/(MgCO3+CaCO3) ratio, with fine-grained and petrographically-complex stones having lower grindabilities. Also, the relationship between the Bond work index and Hardgrove grindability is significant.

Jan 1, 1993

By G. Reed Marchant

In 1967 the US Congress passed the "Clean Air Act." This act was amended in 1970. As a result it soon became obvious that American industries were going to have to make significant changes in their methods of operation to be able to comply with quickly developing federal regulations. One of the first regulations developed was on sulfur dioxide. For this reason, the nonferrous smelting industry was immediately affected by these new regulations. This is true because the smelting process produces sulfur dioxide as a natural product of combustion when the sulfur-bearing ore is oxidized to purify the metal. The federal government's approach for setting standards included public hearings at which government, industry, and private citizens were allowed to make comments. For this reason, it was apparent to Kennecott's Metal Mining Div. that it was desirable to make a maximum effort in working with the agency to see that correct input was provided at the hearings to assist the government in setting fair and realistic standards. It was also obvious that more complete monitoring would be required. It soon became apparent that the efforts required input from many levels of the corporation from the chief executive to the plant operators. In order to accomplish both the administrative and the technical needs, an organization was needed that could respond quickly to these needs, obtain information from diverse sources, and bring it to focus in an organized approach to the problem.

Jan 1, 1979

By R. Edward Williams

The Spa1lation Process Because of the low thermal conductivity of many hard rocks, rapid heating of these rocks produces a thin surface layer in which the temperatures attain high values. Thermal expansion of this surface layer is constrained by the reminder of the still cool rock, and when stresses within the surface rock become high enough, the surface rock breaks away from the cooler rock behind it and flies or falls off as a thin flake called a spall. Then the next, newly exposed surface is heated, and the process continues. This process is the basis of spallation drilling. The hot gases from a jet burner provide the heat for spallation to occur, and their high velocity provides a scouring action that transfers heat to the rock and removes the spalls as rapidly as they form. Spallation is a process which works in very hard rock. It is dependent upon the thermal expansion coefficient and the thermal diffusivity of the rock but is also affected by any discontinuities in the rock. To date the efforts which have been made to evaluate the various rock according to their spallability has been minimal. As the success of this process is dependent upon the characteristics of rock it is expected that the study of rock mechanics will prove to be of greater value to this program than to the other mechanism for drilling and excavating rock. Commercial Uses of SPALLATION In the 19408s, the Linde Air Products Division of Union Carbide (UC 1 began developing spallation for use in mining taconite ore, which is presently the chief source of iron in the United States. In this work UC developed a jet-piercing tool that burned fuel oil with oxygen to produce spallation and contained mechanical cutters to remove rock that was not amenable to spallation. The UC jet-piercing machines have since produced about 40 million feet of shallow blast holes used for emplacing explosives in the taconite mines. During this work it was found that hole diameters could be increased by merely reducing the advance rate of the burners and that existing holes could be enlarged by making another pass through the hole with the same burner. The Browning Engineering Go. of Hanover, N.H., has developed a hand-held spallation burner to cut slots in granite. It has been used for a quarter of a century and is now standard equipment for quarrying granite throughout the world. This burner, which resembles a small jet engine oriented with its exhaust pointed downward, is the forerunner of a flame jet burner used to spall experimental holes in granite at maximum rates in excess of 100 ft/hr when operating in hard, competent granite. It uses No. 2 fuel oil, which is burned with compressed air. The system uses water to cool the burner and the exhaust gases. These gases, along with the steam produced from the cooling water, blow the spalls from the hole. Experimental Work Theoretical and experimental work has been accomplished by the Massachusetts Institute of Technology and the Los Alamos National Laboratory. This work is reported in Refs. (3) and (4). To verify the experimental results of this work laboratory scaled down field tests were conducted using two we1 1 characterized granites from quarries in Barre, VT and Westerby, RI, under defined heating conditions. In the laboratory tests a propane - oxygen heating torch was used to direct a flame at the granite surface and the spal 1 ing process was examined at various heating rates with a high-speed video taping system operated at 200 frame per second. This produced a time-lapse sequence where the onset of the spallation process was easily distinguished. Also the heat flux from the torch to a flat surface at various stand off distances and flows was measured. A similar set of tests was conducted using the more easily quantified and uniform heat source of a 1.5 kw GO2 laser. This allowed accurate

Jan 1, 1986

By Kegomoditswe Koitsiwe, Tsuyoshi Adachi

"This paper characterizes quarterly LME copper price fundamentals from 1995 to 2011 by analyzing the transformation of the market mechanism based on structural change perspective. Using chow test for structural change based on the least square multiple regression, we divide the price fluctuation into: Stable price period (1995Q3-1999Q2), Low stable price period (1999Q3 – 2003Q3) and Price fluctuation period (2003Q4 – 2011Q2). The results show the existence of structural breaks disproves the investigation of the full sample period as a whole. In different structural breakpoints the main drivers of copper prices changes and their impact are significantly different. Moreover, the paper examines the role of speculation in copper price fluctuations.Introduction The rise in commodities price volatility and financial and economic crisis have led to questions over the organisation of futures and physical commodities markets. Spikes in commodity prices and volatility have coincided with a surge in financial speculators in the commodity markets inspiring a polarised and hotly debate among academics and practitioners about the role of investors in the development of physical markets. In his seminal work Kaldor (1939) focused primarily on whether speculative activity in the futures markets reduces the variance of commodity spot prices. Yet, part of the literature finds that the introduction of futures contracts destabilizes the spot market. IMF (2006) studied commodities boom and its causes concluding that there is little support for the hypothesis that speculative activity affects either price levels over the long run or price swings in the short-run. The impact of speculative activity on commodity prices remains a highly contentious topic. Other market analysts take the view that the supply and demand for physical commodities remain the major determinants of market trends (Krugman 2008). It is the aim of this study to contribute to the literature by examining the drivers of copper price changes from a structural change perspective. In this context we are attempting to answer to: What are the main drivers leading to copper price fluctuations? Are these factors having the same effect in different periods or not? It is meaningful to understand drivers of copper prices and thereby, their fluctuations because it will help developing countries depending on copper export to anticipate market situation and avoid bad economic development challenges that can result from price fluctuations. Moreover, this can ensure sustainable mineral supply."

Jan 1, 2017

By L. Spiers

Motorized Conveyor Pulleys contain all the traditional conveyor belt drive components inside the pulley. Light duty airport check in, grocery stores and food processing conveyors; requiring compactness, elimination of guarding and component containment have been using them for years. Portable Aggregate Processing Equipment require these features but with higher belt pulls and severe duty beyond the capacity of traditional components in a limited space. New materials, design technologies and automation; converging with safety issues, higher energy and operating costs; have created a pressing need. The challenge is to integrate new technologies and traditional components into a reliable, compact, conveyor belt drive system.

Jan 1, 2003

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By D. W. Fuerstenau, J. Vazquez-Favela

This paper shows how the efficiencies of size-reduction processes depend on the mode of particle constraint and energy transfer within the comminution device: namely, whether the process consists of single-particle loading, confined-particle-bed comminution or loose- (unconstrained-) particle grinding. The relative efficiency of single-particle comminution, ball-mill grinding and particle-bed comminution in the recently invented high-pressure roll mill is evaluated by making use of the self-preserving nature of the size distributions of comminuted products. The highest energy efficiency can be achieved by utilizing a hybrid two-stage system in which the material is first ground in the high-pressure roll mill and then the ball mill.

Jan 1, 1998

By S. K. Kawatra, S. A. Moffat, K. A. DeLa’O, T. C. Eisele

It was observed that the efficiency of some autogenous grinding circuits was dependent on temperature, with the energy-efficiency of the grinding process decreasing in the winter months, accompanied by an increase in critical-size production. Several possible causes of this phenomenon were suggested, including: • Increased brittleness of the ore during blasting in the pit at low temperatures, leading to increased levels of internal cracking that would lead to rapid breakage to critical size in the mill; •Brittleness changes of the rock in the mill; and • Changes in the durability of the rock caused by either formation of ice on the surface, or freezing of water inside the pores and cracks of the rock. To determine which mechanisms were occurring, drop tests were carried out using frozen and unfrozen rock with varying degrees of porosity, both dry and water-saturated, and which had been blasted for mining in summer and in winter. These tests showed that there was no difference between the summer-blasted ore and the winter-blasted ore, and that durability changes in dry rock over the temperature range from 25ºC to -25ºC were negligible. However, water-saturated rock showed an increased resistance to breakage upon freezing, particularly when the rock was highly porous, or when a layer of ice formed on the surface. Seasonal changes in the durability of rock in grinding are therefore due to formation of ice in and around the rock.

Jan 1, 1995

By M. J. Scoble

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1997