Search Documents

By David B. McWhorter, John D. Nelson

INTRODUCTION The quantity of seepage that will be released from a tailings impoundment depends not only on the characteristics of the seepage control system, but also on the properties of the foundation soil or rock beneath the impoundment and the nature of the groundwater in the area. The interaction between various elements of the seepage control system and the influence the various characteristics of the site and impoundment have on seepage are the subject of this paper. The results of analyses are presented herein to indicate the nature and magnitude of the effect that the various factors will have on seep¬age losses. Analyses were conducted for a uranium mill tailings impoundment located in an area characteristic of many found in the western United States or Canada. A typical seepage control system consists of placement of either a clay or synthetic liner beneath the impoundment. In some cases an underdrain system may be placed on top of the liner to collect drainage from the tailings. The parameters that were varied in the analyses included those pertaining to the liner, underdrains and foundation strata. In general, it is shown that the seepage losses will vary in a complex manner depending on the interaction of the elements of the site and the seepage control system. As may be expected, the liner and underdrain systems have the most pronounced effect on controlling seepage. This paper deals with the quantity of seepage released from an impoundment However, the impact that seepage losses from an impoundment will have on the surrounding environment will depend on the rate at which contaminants will enter the groundwater and the nature of the groundwater flow itself. Consequently, when considering these results with regard to environmental impact they must be interpreted along with considerations of geochemical factors. MECHANICS OF SEEPAGE The mechanics of seepage and methods of analysis that were used will be discussed briefly herein. For a more detailed discussion the reader is referred elsewhere (McWhorter and Nelson, 1978, 1979, 1980). A general column through the impoundment was considered to be as shown in Fig. 1.

Jan 1, 1980

By L. A. Hansen, D. L. Buffington, G. H. Beckwith

This paper reviews geotechnical engineering considerations in heap leach pad design, discusses design philosophy and provides design procedures. A brief discussion of surface water hydrology ground- water protection and other design considerations are also presented. Special emphasis is placed on projects in the arid and semiarid regions of the Western United States where annual evaporation exceeds rainfall, and where good foundation conditions are usually present.

Jan 1, 1987

By F. H. Muge

This paper intends to present a general methodology implemented in a software package and which can be applied, whatever the exploitation methods, mining constraints and time basis, to mine planning and production schedulling. Examples are: presented covering the medium-term and short-term planning procedure and the production schedulling for two underground mines located in the South of Portugal (Neves- -Corvo and Aljustrel Mines). Both are complex suiphide orebodies with differ- ent exploitation methods (Neves-Corvo: cut-and-fill; Aljustrel: Long-hole stop- ping).

Jan 1, 1992

By J. Simmons, P. Ziemkiewicz

Acid-Base Accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality,and permitting decisions for surface mines are largely based on thevalues determined by ABA. In order to predict the post-mining water quality, the amount of acid-producing rock is compared to the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP/MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results to actual overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP/MPA ratio showed the best prediction accuracy. In this study, NNP and the NP/MPA ratio gave identical water quality prediction results. Therefore using NP/MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP/MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two of eight sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four of 40 sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had non-representative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP/MPA ratio of <1 produced acid or neutral drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP/MPA ratios of >2 produced alkaline drainage with a few exceptions. ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Jan 1, 2003

By D. K. Dysinger

Capital resource budgeting is the means by which managers of publicly held companies fulfill their fiduciary responsibility to maximize the wealth of stockholders. Managers maximize shareholder wealth by allocating investment capital to the most productive of competing alternative projects in a manner that maximizes the net present value of the firm&apos;s future cash flow. The techniques of cash flow analysis are the primary tools available for selecting a corporate portfolio of projects that meets or exceeds the rate of return expected by shareholders. The reliability of cash flow analysis hinges on the ability of managers to forecast the future values of individual components. The accuracy and reliability of forecasting determine the soundness of capital investment decisions and, ultimately, determine the value of the firm. The present paper will explore tools for forecasting the spot market price of a commodity, silver, to demonstrate the difficulty and uncertainty involved in forecasting the future. The commodity price is only one of a number of components of the cash flow equation. Each component has a unique and uncertain future and must be individually analyzed and forecast to arrive at a robust cash flow model.

Jan 1, 1997

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine&apos;s heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By H. Dho

Two aromatic-type chelating agents, 1,10 phenanthroline (phen) and 8-quinolinol (quin), were tested as specific depressants for magnetite in the cationic silica flotation of magnetic taconite concentrates. Micro and batch flotation tests, along with zeta potential and adsorption measurements were used. In the presence of a cationic collector, dodecylammonium chloride (DAC), the Fe/phen surface chelate electro-statically repelled DAC, and magnetite was depressed. The negatively charged Fe(quin)2(OH)2-on the magnetite surface attracted the cationic collector and made magnetite floatable.

Jan 1, 1995

By R. T. Webber, D. Moffett, D. W. Averill, G. H. Kassakhian

INTRODUCTION In Canada, radium-226 is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate barium-radium sulphate. Large settling ponds are provided to effect solid-liquid separation. However, the barium-radium sulphate precipitate [(Ba,Ra)S04] is a fine, slow-settling crystalline solid which is not easily removed by simple sedimentation systems. Consequently, settling pond effluents may contain appreciable quantities of particulate or suspended radium-226, depending upon the specific pond system and/or the time of year considered. Also, current technology is expected to be incompatible with ultimate disposal goals since safe recovery of the barium-radium sulphate sludge from the settling ponds may be difficult to achieve (IAEA, 1976). Under the auspices of Environment Canada, a Government-Industry Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical--chemical treatment systems as an alternative to settling ponds. In response to the Sub-Group recommendations, a bench scale feasibility study began in March 1976 at the Wastewater Technology Centre (WTC) of Environment Canada. The bench scale work was expanded and accelerated in 1977 with financial assistance provided by the Atomic Energy Control Board. The results of this study indicated that coagulation and flocculation of the (Ba,Ra)S04 precipitate greatly increased settling rates (Wilkinson and Cohen, 1977). Subsequently, a research program with a larger scope was initiated in January 1978; this program is jointly managed and funded by government and industry as indicated in Table 1. The principal goal of the Joint Government-Industry Program is the development of a physical-chemical process to reduce the radium-226 content of uranium mining and milling effluents. The following effluent radium-226 activities were established as targets for the program: 0.37 Bq/L (10 pCi/L) as total radium-226; 0.11 Bq/L (3 pCi/L) as dissolved radium-226. Process development work was undertaken at bench scale at the WTC and at

Jan 1, 1980

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application, for geological structures, has been criticized, for its reliance on subjective interpretations. The Mine Safety & Health Administration&apos;s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and. fault zones that were parallel with projected lineaments. The Roof Control Division&apos;s successful identification o f lineaments associated with roof falls and high wall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions would allow mine operators to obviate safety concerns that might otherwise adversely affect the health and safety of miners.

Jan 1, 2003

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By M. R. Wormald

A real time data acquisition system has been developed for implementing standard radiometric analytical techniques, applied to the monitoring and control of mineral processing plants. The system uses standard ECB-bus microprocessors and peripherals, in conjunction with a specially designed nucleonic pulse ADC. It is being applied to the accurate on-line analysis of naturally-,occurring radioelements in processing plants, for example by simultaneously measuring the intensity of 1.46 MeV gamma-rays from the naturally-occurring radioisotope K-40, and the stream density by gamma-ray transmission of 662 keV gamma-rays. Gain stabilisation of the NaI(T1) scintillation detectors is maintained by the microprocessor in slave units, each of which may control up to four sample presentation systems. Data analysis - including corrections for bulk density, radioactive decay of the Cs-137 gamma-ray source, pulse pile-up, dead time and external background - is carried out in a master computer which is connected to the slave unit, and can be interfaced to the plant control computer via data links.

Jan 1, 1986

By H. Suharyono

A laboratory investigation of flocculation following polymer addition during slurry flow through pipes and in-line (static) mixers is described. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points on flocculation performance as measured by settling rate and supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests, both batch and continuous, conducted in stirred tanks.

Jan 1, 1995

By S. C. Brown, R. C. G. Oliveira

Surface wettability, or contact angle, dictates a number of multiphase ensemble interactions that influence particulate dispersability and adhesion behavior (e.g., filler compatibility] in addition to a number of other phenomena including biocompatibility and bulk powder segregation. The wettability of particulate surfaces significantly impacts nearly all process industries; however, the available techniques to access this quantity are either relative, or tedious-and are application or industry specific. In this study, key features of existing techniques have been combined to design an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By C. J. Webb

Column experiments were performed to determine the ability of Madison aquifer material to adsorb arsenic and other constituents in a heavily mined watershed of the Black Hills in western South Dakota. The Madison aquifer is a karstic dolomite and limestone reservoir that is exposed on the flanks of the Black Hills. Streams that cross the Madison in the eastern Black Hills typically lose all their flow to the aquifer at sinkholes. In this work, Madison aquifer material was obtained for loading of six-inch diameter columns, which were backfilled with Madison aquifer water. Stream water then was allowed to displace the aquifer water during column testing in order to simulate mixing of the two waters at sinkholes and to determined adsorption of arsenic and other dissolved constituents. Initial results show that some adsorption of arsenic occurred when compared to more conservative tracers such as nitrate.

Jan 1, 1999

By Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

The algorithm presented in this study determines the combination of fans that provide all working districts of a mine with predefined airflows at the minimum operating cost. It is based on an existing ventilation simulator, VNETPC, and a set of linear equations associating fan pressures and the added resistance of regulators. Two assumptions are undertaken: (1) fan locations are predetermined and (2) the number of working districts is equal to or greater than the number of fans. By means of this algorithm, the optimal solution to an n fan ventilation system may be found after n + 1 simulation runs.

Jan 1, 1987

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015