Search Documents

By J. W. Wilson, P. C. Graham

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. Wilson M.Sc., M.I.M.M., F.S.A.I.M.M., M.A.I.M.E. and P. C. Graham M.Sc. (Eng.) Gold mining is being carried out at ever-increasing depths in South Africa. For reasons of safety and human comfort, it is becoming imperative for raises to be developed by means other than conventional drilling and blasting. Raise-boring is an attractive alternative method. Initial raise-boring experiences in South African gold mines showed disappointingly high costs due to the abrasivity and difficulty of drilling Witwatersrand quartzites. Consequently, a research and development project was instigated with the objective of making raise-boring an economically viable technique in hard abrasive rock. A Robbins 61R raise-borer was made available to the Research and Development team and a number of raises have been drilled. During these trials two advances in cutter design were tested. This paper presents the results obtained, including drilling costs, and provides details of the equipment used.

By J. A. C. Diering

The simulation of mining in faulted ground was recently described by Crouch. His method is extended here to enable a wide range of non-homogeneous mining problems to be modelled. Essentially, the boundary conditions at geological interfaces are incorporated into the overall iterative solution, which is necessary if faults and joints are to be modelled realistically. Two examples are given to demonstrate the method: the mining of coal a seam below a thick dolerite sill, and the mining of a flat reef in close proximity to a vertical fault where hangingwall and footwall rocks have different properties.

Jan 1, 1980

By J. H. Bulloch

A study of fatigue-crack growth in a rail steel and an associated weld metal showed that fatigue cracks in the deformed rail steel had slightly higher growth rates than in undeformed rail steel. The crack growth in the weld metal was appreciably faster than either and exhibited plateaux that were above the upper bound reported for rail steels, The cyclic-life curves showed that, over an indicated service period of 8 years, both the deformed and the undeformed rail steels should not be prone to fatigue failures under the defined mechanical conditions, For the weld metal, the cyclic-life curves indicated the possibility of premature fatigue failures but, as al the input parameters represented a 'worst case' situation, this assessment could wel be ultra-conservative. In the rail steels at low levels, the extension of the fatigue cracks occurred by ductile striated growth. At a Kmax level of 35 MPa .J/n, cleavage facets formed initially on the surface of the fatigue fractures, and their incidence increased with Kmax until the onset of fast failure, The microstructure of the deformed rail steel exhibited cleavage facets at a slightly lower Kmaxvalue, and contained more cleavage facets at a given K level, than the microstructure of the undeformed rail steel. The average size of the cleavage facets agreed well with the pearlite nodule dimensions of 60 to 100 ILm. The microstructure of the weld metal was much coarser and contained columnar grains. At al f.K levels, the dominant fracture mode was cleavage, with small isolated regions of ductile striated fatigue cracks. The size of the cleavage facets varied from 150 to 600 ILm, and such a variation may be explained by the fact that cracking generally occurs in association with the pro-eutectoid ferite phase, and that this phase is distributed along some boundaries of prior austenite grains and the boundaries of the coarser columnar grains.

Jan 1, 1987

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

By P. Wiesner, H. –M. Stonner

A brief account is given of the influence of sulphuric acid and chloride ions during the recovery of uranium by solvent extraction, followed by a discussion of the settling behaviour of dispersions and models to represent that behaviour. The paper ends with a description of various methods for the recovery of solvent, which is lost in the solvent-extraction process by entrainment and adsorption on solids and by dissolution.

Jan 1, 1982

n interesting situation arose last week when two Vaal River residents wrote to me (and a third telephoned) giving me details of how Sasol wanted to develop an open-cast coal mine on the south bank of the Vaal, just upstream of the Barrage. This is agricultural land and is across the river from Millionaire?s Row, where a number of wealthy people have built river-side mansions. The mine would be hidden by a 30 m-high (10 storeys) earth wall set 300 m back from the edge of the river. It could operate 24 hours a day.

Jan 1, 1996

By J. M. Stewart

Mining fatality rates in many countries have not changed substantially over the past ten years. This demonstrates not only that there is an inherent risk in mining, but also that current approaches to improving safety need to be rethought. An analysis of productivity and fatality data in the United States, United Kingdom, and South 4frican coalmining industries shows that the impact of legislation on safety is overlain by other significant factors. Although improvements in safety and productivity usually occur together, the data warn that safety legislation can sometimes cause a significant reduction in productivity. Based on the data and experience considered, it is concluded that legislation should be aimed at creating a framework within which a positive attitude towards the implementation of more productive and safer mining methods, work practices, and technology can flourish, rather than attempting to enforce excessively prescriptive provisions. This later approach is even more problematic when safety standards and legislation are transferee from well developed to less developed countries. A legislative framework in which the mine manager is required to take al reasonably practicable measures to procure safe working conditions in accordance with mine-specific codes of practice is outlined. Within that framework, the value of adopting widely accepted standards is recognized. A performance-based external audit arrangement is outlined as a basis for ensuring that detailed attention is focused on those areas most needing improvement.

Jan 1, 1995

By T. K. Roy

INFACON XI has no doubt earned the distinction as the first such Congress in India. This prestigious occasion could become a reality of a long cherished dream of the Indian Ferroalloy Producers, consumers and ex-porters. The International Committee of Ferro Alloys (ICFA), South Africa, the august body for organising INFACON, every three years, could be convinced by the Indian Ferro Alloy Producers? Association (IFAPA) to award INFACON (XI) to India. This Congresss, organized by IFAPA, has opened a window for the Ferroalloy Community of India, the up-coming Asian Tiger, to register their strength and weakness to the world forum with the principal objectives of evolving long and short-term optimum road-maps for development. It is to be reckoned that India is poised to be a steel giant by 2020 when it is envisaged that the steel production may reach a level of 120 million tons of which significant proportion has to be in the categories of alloy and special steels, requiring standard and high grade ferroalloys. Keeping the above objective in view, the theme of this Congress has been rightfully designed as ?Innovations in Ferro Alloy Industry.? This Congress has also earned a distinction of more than eighty papers, finally selected for inclusion in the Proceedings. More than 100 internationally and nationally reputed experts in the field of ferroalloys (technology and manufacturing practices as well as world scenario) have been approached for critical review of abstracts and selection for the proceedings. It needs to be mentioned without the cooperation received from ICFA the high standard of INFACON could not have been assured. The papers are suitably grouped under seventeen heads, starting from world situation to production and operation followed by present and future technologies and finally to modelling and simulation. It is a Herculean task to the Technical Committee to fit these papers in proper sequence. The Commit-tee members kept no stone unturned to ensure the cogency with the subject matters and at the same timekeeping the flexibility of interests of the participant, especially in the context of three parallel sessions. The Proceedings containing only refereed papers of high quality, will serve the entire gamut of ferroalloy industry and will also highlight the present status of concerned countries. The areas of attention to make the industries globally competitive and at the same time laying emphasis on the prevailing practices, will help the industry leaders to formulate an appropriate global approach. Following the break-through step, instilled by INFACON XI, the Proceedings will be available both in bound and in searchable electronic CD-ROM format. I, as the Chairman of the Technical Committee would like to express thanks and high appreciation to all the Committee members for their whole hearted efforts in all respects without which it would not have been possible to complete these proceedings in the scheduled time. Technical Committee desires to place on record their gratitude to Organising Committee for their synergic cooperation all through in successfully executing multifarious tasks, associated with such a grand international technical Congress.

Jan 1, 2007

The 90th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 19th August, 1987. Dr H. Wagner (President) was in the Chair and declared the meeting open at 16h00. Obituaries The President read out the names of the departed Members as follows: N.M. Airey, F.J. Kisbey-Green, Dr R.A. Pelletier, C.B. Anderson, A.R. Cator, J. van Heerden, P.J. Burman, C.C. Crosson, M. Livingstone¬Blevins, S.T. Firman, V.E. Kisbey-Green, and A.L. Corna. All stood and observed a moment of silence as a mark of respect. Minutes The minutes of the 89th Meeting of the SAIMM, which was held on 20th of August, 1986, were confirmed.

Jan 1, 1987

By J. A. C. Diering

The determination of stresses and displacements close to tabular excavations is of considerable importance in the planning of tunnels and of remnant and pillar layouts. This paper gives a description of a simple yet effective method for the achievement of improved values from an analogue or MINSIM type of analysis. Essentially, closures and rides (the movement of hanging-wall relative to footwall) in mined-out areas are assumed to vary in a piecewise linear fashion as opposed to a piecewise constant fashion. As the former fashion more closely resembles the true variation, it is possible for the stresses and displacements at points close to the excavations to be calculated with much better accuracy.

Jan 1, 1980

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By R. M. Morris, G. A. Matthesius, M. J. Desai

Slow pyrolysis experiments were caried out on samples of coal from north em Natal having a volatile mater content ranging between 10 and 25 per cent by mass and a constant particle-size distribution. The tests were conducted at atmospheric pressure in a helium atmosphere, and ata heating rate of 10 KImin and a final temperature of 1220 K. The pyrolysis products were taken as coke and volatile mater (tar and eight other species), and tMir respective yields were measured. The experimental results were used in the modification of an existing mathematical model and in the derivation of new corelations for some of the parameters of the model, so that the volatile products of a coal can be predicted from ultimate and proximate analyses of the coal. The pyrolysis tests showed good agreement between the model predictions and the experimental results.

Jan 1, 1987

Dr H. J. van Eck (Honorary Life Member): "Mr President, I regard it as a signal honour that I was invited to address the South African Institute of Mining and Metallurgy on its 75th Anniversary. I also wish to add my congratulations and good wishes to the many you have already received on this memorable occasion. Seventy-five years is indeed a good age and the achievements of your Institute certainly justify this special celebration. South Africa owes her present prosperity largely to the technological ability and determination of her own people. Members of the Institute contributed in large measure to this great development of our country and through the years have upheld their high reputation for scientific integrity, dynamic enterprise and dedicated service. It was their knowledge which provided the key to unlocking the mineral wealth which lay dormant for countless ages. The history of world mining dates back many centuries. We know of the mercury mines of Spain, the tin mines of Cornwall and the zinc mines of Poland, but it was not until colonization of the western hemisphere started in about 1500 that mining of any consequence began in North America. It is true that the peoples of South America and Mexico had accumulated wealth out of gold and silver, but industrialized mining was not a feature of these agrarian cultures. The mining wealth that eventually developed in North America was based on advances in the technology of processing minerals and served as an incentive to people in other new countries. Big mines were opened elsewhere in the world. From Canada, Mexico, Venezuela, Brazil, Peru, Chile, Bolivia, Rhodesia, Australia, Burma and India, to name but a few, there has been a steadily increasing production of an expanding range of minerals and metals. By the middle of the 20th century the trend was to increase the production and use of such comparatively uncommon metals as cobalt, nickel, titanium, and others, and a great mining rush started to search for, and develop, the deposits of uranium, and related radio-active minerals. It is worth pausing a few minutes to reflect that most of early mining was based on the recovery of virgin metals like gold and silver or easily treated high grade ores of copper, tin and zinc. Today, much of this type of mining would be regarded as picking the eyes out of the mine. With the development of improved ore separating, ore concentration and recovery processes, we developed into bulk mining and bulk treatment and in South Africa we have some very big mines, also outside the gold mining industry at Phalaborwa, for instance. Mining techniques are applied which compare with the best in the world. These large mines could only develop because of the perfection of new concentrating techniques and, of course, because of the development of markets. We have mentioned nickel and cobalt. These names were given to those mischievous mining sprites called nickels and kobolds to whom the suspicious miners ascribed their inability to smelt copper from copper nickel or arsenious copper ores. In South Africa, the presence of minerals was known to the modern Western world as far back as 1497 when Vasco da Gama found the native 'strandlopers' at the St. Helena Bay wearing copper rings. In 1669, after the British East India Company had formed their settlement, they employed miners and assayers in prospecting for minerals and in 1685 found traces of copper in the copper mountain of Namaqualand where some 170 years later a rich deposit of copper was to be opened up. This deposit also had a chequered

In the previous chapters we did not concern ourselves with the fact that the geostatistical properties of the regionalized variable x (z) are affected by the size of the support w. Ideally, when analysing an ore body O, we would like to determine the properties of point values in O, i.e. the properties of a regionalized variable with an infinitely small support, say w°. In practice, point values are never known. To measure the value of x at a point z we must take a sample of size w centred at z. For example, if we are interested in the grade at point z, w will be the volume of the sample 'centred in z; if we are interested in the metal accumulation at point z, w will be the area of the cross-section of the sample centred in z. We say that the measured property is a regularized variable, and so the semivariogram (or covariogram) calculated from the values obtained is also regularized. In the majority of the mining problems which can be solved by geostatistical methods, we are interested in the properties of blocks of ore and of samples with a finite non-point support. It will be shown in the following chapters that these problems can be solved by calculating the average value of the point sernivariogram in volumes or areas of finite dimension, or between such volumes or areas. These calculations would be simple if we knew the point semivariogram. This means that the point semivariogram has to be estimated from the observed regularized semivariogram(s).

Jan 1, 1978

The 101 st Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 12th August, 1998. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents H.E. Cross, D.G. Malan, P.W.J. van Rensburg Life Fellows J.B. Rolfes, W.C. Walmsley Fellows H.F. Boshoff, M.L.A. Fitzgerald, J. Humphriss Retired Fellows H.S. Botha, E.Collier, J.L. Curtis, A.H.H. Davison, D.I. Legge, B.D. McNeice, J.A. Northcott, D. de V. Oxford, S.S.K. Penney, P.C. Pirow, J. Pope, A.J. Rossouw, A.N. Shand, E.P. Smit, H.V. Solomon, S.G. Taussig

Jan 1, 1998

Currently the most widely used formula in pillar design is the power formula, which implicitly assumes a volume effect. This assumption is critically examined, and it is proposed .that a limiting strength value, the critical rock mass strength, be used for pillar design instead. A methodology is provided to determine this value. It is suggested that the effects of geometry on pillar strength are well described by a linear function and the power formula, for w/h ratios less than or equal to about 5. This approach together with the use of the critical rock mass strength, removes the volume effect. Various factors that affect pillar strength are examined. The concept of explicitly determining the stability of each component in the pillar system is briefly discussed. It is proposed that pillar design be expanded to a pillar system design procedure that incorporates the interaction of the pillar, roof and floor strata, and the loading system.

Jan 1, 1998

By M. Arnesen

Mining professionals recognize the need to continuously evaluate and refine mine planning standards and scheduling. We must examine our current reality, and evaluate the following: •How well do our planning standards represent the actual mining process? •To what extent do they support the requirements of the downstream mining activities? •How we apply them to operational management and control? In most operations, mine-planning standards are global averages. Little differentiation is madein quantifying key planning variables. Often standards used in the long-term, are applied to the short-term, and the standards and scheduling precedents are only reviewed occasionally. Mine-planning standards applied to production schedules are often only focused on the management of functional mining performance, and play no role in managing the requirements of down stream processing. Many mining operations are characterized by high levels of fluctuation, and typically incorporate a wide range of factors and adjustments to compensate for deviations from performance targets, in mining operations as well as for the other business areas. The reason for using global averages is because of a lack of understanding of the causes of deviations that occur through the process, and the impact that they may have on the performance of the business as a whole. Average standards and factors are often used to quantify the variability in a system. From these average values, measurement standards and performance targets are derived for the planning and execution environments. During the execution of a plan/schedule there will be deviation in actual performance and the planned ‘average’ standards. In reality the ‘average’ conditions seldom occur and the impact of variability and interdependency are seldom constant or predictable. The predictability of variability and interdependency is further complicated by the fact that mining conditions have a role to play in the actual production performance, and they too are variable. By developing the throughput knowledge of our production systems, we can better understand the nature of variability and the interdependency within the systems as well as the impact of interdependency between the links in our production chains. With this knowledge, planning standards and scheduling precedents can be better defined and sensibly differentiated. This will improve planning and management of ore utilization, mining production and the effectiveness of processing. As a result the business will be more stable and predictable and business performance will be improved. The purpose of this paper is to describe: •At a high level, the scope for refining and differentiation in mine planning standards, and incorporating geological and plant parameters into mine scheduling. This will improve planning and scheduling and the overall performance of the mine. Given our current level of scientific knowledge and the technological tools at our disposal we should be able to plan and schedule production so that we can manage pro-actively and improve business performance. In doing so we can also improve reconciliation and value tracking through mining and processing •The flexibility and functionality of the XPAC planning and scheduling tool that will enable a throughput management approach.

Jan 1, 2003

By K. Böde

Hochtief AG Germany has developed a comprehensive management and information system for the construction industry named Aristoteles. This system is an efficient supporting tool to manage a variety of construction sites as well as operating business units with required economic targets. As such, Aristoteles offers wide-ranging control of complex economic processes in construction in a consistent manner. In this paper the process oriented functions of the system will be described with special emphasis on finance accounting and cost control. The basic elements in this respect are tender estimation, creation of initial project budgets and running budgets, regular determination of work done and result forecast to the end of the project. Further, cost accounting, monthly reporting, and all balance-related postings are included. On the basis of the extensive reporting (targeted/actual cost comparison, cost manager, project report, actual/targeted hours worked comparison, overhead cost report, amendment report or project (result) lists of all projects realized by one business unit), the responsible managers can make justified project evaluations, project controls and variance analyses during the project period and derive appropriate management measures. Thus, Aristoteles includes all substantial elements for the risk management of the operational business. In big construction joint-stock companies it is of crucial importance to satisfy the information requirements of the investors. In this respect the system provides a transparent presentation of the financial, investment and profitability situation of the company. In the international construction industry the balancing rules according to IAS (International Accounting Standards) have already been used to a larger extent. In accordance with these rules the partial profits of the work during execution can be shown as realized even before completion of a long-term contract. The validity of Aristoteles will be outlined briefly. Major advantages using the system are highly enhanced accuracy of project controlling, systematic overhead allocation to projects, change of attitude of the project personnel due to increased cost consciousness and improved flow of information within the company.

Jan 1, 2003

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981