Search Documents

By A. Golder, S. P. Dandapat, I. Roy

One of the consequences of large-scale opencast mining for coal is the disposal of an enormous volume of overburden material that needs to be removed. With the enlargement of opencast mines and associated high stripping ratios, the volume of overburden extraction is rising. Overburden from the initial mine cut has to be necessarily dumped outside the mining area until enough void is created inside the mine for back-filling operations. The quantity of overburden placed outside the mining area normally varies from 10% to 30% of the total overburden removal. The stability of these dumps placed outside the mining area is of prime importance from the point of view of smooth operations of the mines and safety of persons in and around the dumping area. Owing to increasing pressure on land use, mine operators do not have any other option other than to place the waste dumps very near to the surface edge of the pit, which may lead to failure of the topsoil benches of the working pit. This study identified major controlling parameters that influence a stable but economic combination of height and slope angle of external dumps located close to the edge of an open coal pit.

Nov 27, 2024

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By D. van der Westhuizen, H. Krieg, M. Kruger

In the field of Fischer-Tropsch synthesis catalysts, cobalt, platinum, and aluminium are the primary metal constituents of the conventionally used cobalt catalyst. While platinum recovery remains a focal point in this field, a recent endeavour by a South African company emerged, which aimed to recover cobalt and aluminium from spent Fischer-Tropsch synthesis catalysts for potential use in the agricultural sector. This study aimed to optimally separate cobalt and aluminium from spent Fischer-Tropsch synthesis catalyst for this purpose. It further leverages the OLI database to predict metal speciation during solvent extraction to aid with experimental planning. Shake-out tests were conducted to determine optimal separation. conditions, which were validated using three distinct methods: (i) evaluating the experimental error, (ii) comparing results with similar research, and (iii) validating results against the OLI database. The investigation revealed the pivotal role of the aqueous pH yielding effective separation at pH 3.13 ([H2SO4] = 2.5 × 10−4 M) when using 20 vol.% CYANEX 272 and 50 mol.% pre-neutralisation. Effective cobalt scrubbing was achieved with 50 g/L Al at pH 2.8, while successful stripping required 1 M H2SO4. Competitive interactions between complexing aluminium and cobalt species were observed when contacting with CYANEX 272 at a pH < 4. Equipment design analysis for a targeted separation efficiency of 87% dictated the necessity of two mixer stages and a settler measuring 1.5 m × 1.5 m × 6.0 m (height × width × length). This settler would ensure sufficient residence time for gravity separation at a flow rate of 10 m3/h.

May 27, 2025

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluoridesl.2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02?SiO2) with the ammonium acid fluoride (NH4F?XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo-dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By J. O. Claassen

"Homogeneous populations are required to perform descriptive, probabilistic, and inference statistics and to support stable, predictable mining operations. The geological and downstream processing environments are, however, highly heterogeneous. The complex nature of mining environments requires means to identify and define multipopulation environments that could affect the performance of mining value chains. A study performed at several operating mines suggests that the impact of heterogeneous or variable geological, mining, and plant processing environments on overall mining value chain performance may not be a key focus area at these operations. This was illustrated through the use of basic and spatial statistics, which included the log-probability plot, a modified range equation, and chronovariography. The findings reflect high relative variability in the geological and processing environments studied and mining operators’ inability to effectively deal with the sources and consequences of variability. The study suggests that a focus on heterogeneity in complex mining operations may significantly enhance overall mining performance. IntroductionHeterogeneity and why it mattersHeterogeneity refers to a state or quality of being variable/diverse and comprising different non-compatible elements or parts. In statistical terms a heterogeneous population can refer to a population comprising different non-compatible sub-populations or a multipopulation environment. The latter is commonly found in natural environments such as geological environments (Bardossy and Fodor, 2001). The inherent heterogeneity of complex geological environments is also referred to as spatial heterogeneity. Heterogeneity or variability, however, also occurs over time at mining operations. A case in point is variable ore composition on a conveyance system feeding a processing plant or product stockpile.Heterogeneity associated with the mining environment can significantly influence key aspects of day-to-day mining operations such as sampling, the use of descriptive, probabilistic, and inference calculations, and an operation’s ability to manage and control the mining value chain as a whole."

Jan 1, 2016

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By P. C. Pistorius, M. P. Maphutha, J. D. Steenkamp

Advanced high-strength steels (AHSS) are sophisticated materials being developed by the steel industry to mitigate challenges related to the performance of motor vehicles. To meet the requirements of AHSS, the ferromanganese alloys (FeMn) utilized in the production of the steel are required to contain acceptable levels of unwanted impurities, i.e. P, S, N, H, and C. The focus of the current study was to investigate dephosphorization of ferromanganese to produce a low-P alloy that could be effectively utilized in the production of AHSS. The study involved conducting laboratory-scale testwork to study the efficiency of CaO-based slag systems to dephosphorize FeMn alloys. The addition of Na2O, CaF2, and BaO to MnO-CaO-SiO2 slag was considered. The test work was carried out in a 25 kW induction furnace at temperatures of 1350°C, 1400°C, and 1450°C. The P partition coefficient (Lp) remained small at <1, which is an indication that dephosphorization had not been achieved. The baseline slag, comprising 40%CaO-40%SiO2-20%MnO, reported higher Lp values. Addition of Na2O and CaF2 did not show any further benefit. Substituting half of the CaO by BaO, resulted in similar Lp values to those of the baseline slag under conditions of 1350°C and 1450°C at 30 minutes. In summary, based on the Lp values obtained, the conditions investigated with the CaO-based slags appeared to have been unfavourable for dephosphorization of FeMn alloys, as most of this impurity element remained in the alloy.

Sep 1, 2021

By R. G. B. Pickering

Successful management of mining operations depend on the accurate and reliable measurement of performance as a monitoring instrument in a feedback and control loop. However, when changes are being considered, the probable effect of the change on bottom line results requires different measuring techniques incorporating an in depth understanding which can identify hot spots in the operation which exhibit strong sensitivity to change. The CSIR&apos;s Division of Mining Technology has therefore been devoting a considerable effort to the establishment of techniques which enable changes to be analysed in terms of their impact on the two key parameters describing mine performance, i.e. profitability and safety. This paper describes these techniques, outlines their application to some example situations and discusses planned enhancements. The first section of the paper addresses the profitability model, and this is followed by a section considering the mine safety model.

Jan 1, 1996

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By T. Uysal

Various morphological parameters that affect the flotation recovery of sphalerite were modelled and optimized using the response surface method (RSM). The effects of roughness value, shape factor, and collector concentration were investigated using the central composite full design method. The results were evaluated by analysis of variance. The optimum roughening time was found to be 25minutes, the optimum roughness value was 2.9071 μm, and the optimum collector concentrationwas 0.001 M. Using these values, a flotation recovery of 98.01% was obtained. Similarly, in shapefactor studies, the optimum grinding time was 15 seconds, the optimum roundness value 0.7421, and the optimum collector concentration 0.0009 M, which resulted in a flotation recovery of 94.30%. The average error between the optimization results and the experimental results was estimated to be less than 6%, and the R2 values were greater than 90%. The study shows that RSM can be effectively applied in finding the economic optimum condition for obtaining maximum flotation recovery with minimum reagent consumption.

Sep 6, 2023

By V. Jokovic

Hydrocyclones are the most commonly used classifiers in the mining industry. The reason for this is their low operating cost and a small footprint. Data from plant trials where screens replaced hydrocyclones indicated that lower bypass of fines and sharper separation could improve breakage rates, with a positive effect on flotation circuit performance throughput. Despite the importance of classification, hydrocyclones have not received as much attention as more expensive comminution units, and their technological progress has been incremental. Noticeable water split (Rf) reductions of a semi-inverted hydrocyclone have been reported in the past. According to theory, the hydrocyclone with reduced Rf will improve classification of fines. A classification study using semi-inverted hydrocyclones was conducted to determine if a hydrocyclone could be operated in a way that would minimise misclassified fines. The classification performance of a semi-inverted hydrocyclone will be presented in this paper and other potential applications will be discussed. Keywords: Semi-inverted hydrocyclone, water split, misclassification of fines

Jan 1, 2020

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

Council and Standing Committees, 1979-1980 President: D. A. Viljoen. Senior Vice-President: Dr P. R. Jochens. Junior Vice-President: G. Y. Nisbet. Honorary Treasurer: Dr D. G. Krige. Immediate Past President: Dr M. G. Atmore. Members of Council: J. D. Austin, A. N. Brown, J. A. Cruise, C. E. Fivaz, J. S. Freer, P. N. Harris, H. E. James, Dr R. P. King, Prof. F. Q. P. Leiding, Dr B. K. Love¬day, D. G. Malan, C. S. Macphail, J. C. Mostert, H. G. M. Rose, G. C. Thompson, R. A. von Maltitz, Dr H. Wagner. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plowman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg, P. A. von Wielligh. Chairman, Witbank-Middelburg Branch: R. B. Smith. Chairman, Orange Free State-Klerksdorp Branch: W. C. Mather. Materials Engineering Division, Chairman: Dr J. P. Hugo. Secretary: G. Pienaar. Standing Committee Chairmen: Membership, G. Y. Nisbet; Technical Programme Metallurgy, H. E. James, (Prof. R. P. King) ; Technical Programme Mining, H. G. M. Rose; Vacation School Metallurgy, J. C. Mos¬tert; Vacation School Mining, J. D. Austin; Awards, Dr M. G. Atmore ; Excursions, A. N. Brown ; Adjudications, Dr M. G. Atmore ; Constitution, Rules, and Policy, Dr M. G. Atmore ; Monograph Series, Dr M. G. Atmore ; Training and Career Guidance, P. A. von Wielligh (D. G. Malan) ; National Phoenix Committee, Dr R. E. Robin¬son; 1982 Council of Mining and Metallurgical Congress, Dr M. G. Atmore ; Mines and Works, Dr M. G. Atmore.

Jan 1, 1980

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021