Search Documents

By F. A. Young

A description of the dry process coal cleaning plant which has been built and operated by St. Louis, Rocky Mountain & Pacific Company at their mine at Brilliant, New Mexico, should at first be a description of the special machinery which is used in this process. This equipment consists primarily of screens for sizing the coal into six different sizes all smaller than 1 ½ inch and the pneumatic machines for cleaning each size. These machines are patented and were manufactured by Sutton, Steele & Steele of Dallas, Texas, until a few months ago when all rights of sale were acquired by the American Coal Cleaning Corporation. These screens, a plan of which is now before you, are called anti-gravity screens because the coal travels up hill. The screens which we have at Brilliant are 3 feet wide and 7 feet 4 inches long. They consist of one upper deck which slopes upward in the direction of the flow of the coal, at an angle of 12 degrees. This deck is a wire mesh screen the size of which determines the size of oversize from that screen. Under this is a lower deck with a slope of 7 degrees. This is a solid bottom and is for advancing the undersize to the next screen. On account of the difference in pitch of these decks they are about 11 inches apart at the discharge end, which allows the oversize to be taken off at one or both sides and the undersize to fall only a few inches on to the following screen. This is perhaps the most valuable point in this patent as it allows any number of screens to be placed on a-level floor, tandem in a battery without elevating or rehandling the coal in any way. The length of the screens corresponds to the proper spacing of the cleaning tables which naturally operate on the floor below. I know of no other screen which can be operated in this way. The coal is caused to travel by a reciprocating motion. A shaft as shown near the center of the screen box and under it has an eccentric at each side of the screen with connecting rods attached near the rear of the screen box. The screen box is attached to the stationary under frame by means of cast iron plates extending full width across the screen box. These are placed at an angle as shown so that the forward motion of the eccentrics causes the screen box to rise as it moves forward and the backward motion drops the screen from under the coal thereby causing it to advance. The coal advancing over the screen cloth in this rolling or jumping motion causes very perfect sizing. It should be stated here that very accurate sizing is necessary for the success of the cleaning tables. The stroke is 1 inch and the speed 350 revolutions per minute. In describing the pneumatic cleaning table, I place before you a plan furnished by the makers. The basic principle is that if a film of coal one to two inches thick and all of nearly the same size pieces is placed on a flat perforated surface and a large volume of air passed through it, the lighter particles which are the clean coal will soon find their way to the top of the film, while the heavier particles, or waste, will remain on the bottom. The machine is built with a perforated deck about 4 feet square under which is an air chamber and air duct connecting with a fan which is part of the machine. The deck of the table has a reciprocating motion the same as the screens already described, which tends to advance the product up a slight slope which is adjustable. The coal is fed at one corner of the table as shown and the deck slopes also away from the feed and at right angles to the reciprocating motion. On top of the perforated deck are riffles about 2 inches apart and running parallel to the line of reciprocating motion. These riffles are about 1/2 inch high at the fan and feed side of the table and taper to nothing at the far side. When the coal is fed on to the table, the air through the perforations tends to raise it 'and roll it over these riffles down the slope toward the clean coal discharge. The heavier particles do not get over the riffles so rapidly and the reciprocating motion is constantly pushing them

Jan 1, 1923

Jan 1, 1927

MR. MARGOLF: Thank you very, very much Harris. There's sure a lot there to think about in terms, of our image, particularly. I think we should keep' in mind what Harris said about our history not being monolithic. Therefore our image can only be that, which is reflecting the weakest link in our industry and I think that's a burden on all of us. Perhaps to do some policing amongst ourselves to try to improve whatever might be our weakest link and thereby elevate our entire industry. Our third speaker this afternoon is another good friend of mine of long standing and I am very pleased to be able to introduce to the Rocky Mountain Coal Mining Institute Bob Golten. Bob is a graduate of the University of Michigan with a degree in Economics and Harvard Law School. His professional experience encompasses private practice in Chicago where he was born and in the federal government as a public defender in Washington, D.C. and in the Department of Justice as a tax , attorney. Some of us have come to know Bob more in his present role as the senior counsel for the I National Wildlife Federation. He's also Adjoint Professor of Law and Director of the National Wildlife Federation Resource Clinic, University of Colorado. Boulder campus. In addition, Bob has served with the Rocky Mountain Center on Environment as one of its directors for a number of years. He's very active in a number of areas that are not only civic but he does reflect what I would present by way of introduction as a perspective

Jan 1, 1982

ACM Equipment Sales Co. ACM/ICM Andalex Resources, Inc. ARCO Coal Company Behre Dolbear & Company, Inc. Coastal State Energy Company Colowyo Coal Co. L.P. Commercial Testing & Engineering Company Continental Conveyor & Equipment Company Crane & Hoist Cyprus Amax Coal Company Dakota Coal Company Driltech Inc. Empire Machinery Energy West Mining Company Fleischli Oil Company Inc. Halbach & Braun Industries Hemscheidt Corporation GH Hensley Industries Ingersoll-Rand Company Jennmar Corporation Joy Technologies, Inc. K & P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation LeTourneau,Inc. Long-Airdox Company Magnum Metals, Inc. McLanahan Corporation Morgantown Machine & Hydraulics Morrison Knudsen Corporation National Mining Association The North American Coal Corporation Peabody Coal Company Phillips Machine Services, Inc. Pincock Allen & Holt Powder River Coal Co. Ramsey Technology, Inc. Rust Tractor Company Salt River Project Savage Industries Inc. Stamler Corporation Tamarron Resort TerraMatrix Inc. Texaco Lubricants Company TIC (The Industrial Company Wyoming, Inc.) Trapper Mining Inc. Wagner Equipment Comp any Western Energy Company Wheeler Machinery Company

Jan 1, 1995

The 70th Regular Meeting of the Rocky Mountain Coal Mining Institute convened at the Steamboat Village Inn, Steamboat Springs, Colorado, and was in session at 10:00 a.m. The session was called to order by Past President O. F. Lewis. Consultant, Colowyo Coal Co., Denver, Colorado. Mr. Lewis introduced President A. F. Geiger, Manager, Navajo Mine, Utah International, Inc., Fruitland, New Mexico. Following are Mr. Lewis' remarks: Ladies and gentlemen, members of the institute, guests and friends, welcome to Steamboat Springs and the 70th meeting of the Rocky Mountain Coal Mining Institute. From all appearances this is our largest meeting and should be the most successful. When I last spoke to you I was President of Colowyo Coal Company and the Rocky Mountain Coal Institute but that has changed. Colowyo Coal Company was acquired last Dec. by W. R. Grace & Co. and operates as Colowyo Coal Company, Division of W. R. Grace & Co. I am confident these people will make a worthwhile contribution to the coal Industry.

Jan 1, 1974

[Adams, Leonard E.819 Newhouse Bldg., Salt Lake City, Utah Adams, V. H422 East San Miguel. Colorado Springs, Colo. Allen, Earl W.2636 So. Gilpin St., Denver 10, Colo. Allen, Thomas State Coal Mine Inspector, State Office Bldg., Denver, Colo. Ambler, J. B P. O. Box 591, Denver, Colo. Apperson, A. B 394 Elm St., Denver 7, Colo. Arnold, G. O Phelps-Dodge Co., Dawson, New Mexico Audin, Abel Somerset, Colorado Audis, Clement, Jr. Paonia, Colorado]

Jan 1, 1948

MR. STOUT: The picture shows the plan of the "V"-system as worked at Berwind mine, in a small strip of coal adjacent to the 4th right entry. The dotted line (indicating) show the position of the break rows as set for each of the three consecutive breaks. In two cases the break rows failed to function properly and as a result, the roof caved along the points of the "V's" as well as back along the faces a short distance. This affected the ventilation to a certain extent, but was remedied immediately by cutting through the points near the cave and setting additional timbers. At the present time we are putting in the break row of heavy red spruce props, making the row straight instead of curved as is shown in the picture; in this way we believe we can better control the breaks. The three "V" entries were driven up 14 feet wide, for a distance of 260 feet without cross-cuts. A very neat and substantial line brattice was carried up each entry as the places advanced. The principal factors in determining the success of this system are ventilation, roof control, and transportation. We are well pleased with the results from these three "V" places and now have four other places, about 500 feet to the west of these, driving at the present time in which we hope to get still better results. A MEMBER: What centers did you use there? MR. STOUT: We used 70 feet. This may be increased or decreased according to local conditions. MR. F. W. WHITESIDE (Chief Engineer, Victor-American Fuel Co.) Will you please describe roughly how your cars are handled? MR. STOUT: Cars are brought from the parting and pushed up along the faces by a storage battery locomotive. The faces are about 70 feet long and we found that five or six cars can be loaded and transported very conveniently. It is important to get a quick exchange of cars, and in this way we were able to keep the shovelers busy at all times. A MEMBER: What is the grade in your "V" entries? MR. STOUT: Five per cent in favor of the loaded trip. A MEMBER: What is the angle of your "V" faces? MR. STOUT: The angle at the throat is 45 degrees. MR. SAMUEL ANDREWS: In what direction does the air travel? MR. STOUT: The air travels down the dip entries and is deflected up the first "V" entry, and travels along the points, and returns down the last entry. There is no more difficulty in ventilating "V" faces than in ventilating rooms, providing the points are kept open. A MEMBER: What amount of air do you have in that section? MR. KAISER (Superintendent, Berwind Mine): Eighteen thousand cubic feet per minute. MR. ANDREWS: It is necessary, Mr. Stout, to brattice these places?

Jan 1, 1925

The thirtieth regular meeting of the Rocky Mountain Coal Mining Institute was called to order at 11: 20 o'clock A. M., Wednesday, June 3, 1931, President G. A. Kaseman presiding: PRESIDENT KASEMAN spoke in part as follows: I have in mind to say a few words of welcome to the coal operators, but I am afraid that the words I might have said would be hardly appropriate, because I believe the coal operators are in the minority today. It demonstrates to my mind something that has been running through it for some little time. When the hard times came on a year ago, we thought we were going to get over it rather lightly. I recall at this time a year ago we thought that the depression was about at an end. The National Administration from Washington told us we had reached bottom and things were going to perk up, and for a few weeks or maybe a month or more there was a sort of optimism throughout the country. I had been East, and when I re- turned to Albuquerque I said to my friends and associates that things were getting better in the East and that they would soon be better out here and we will not have felt the hard times very much. But I have learned differently since. I have learned that hard times are no respecter of communities or corporations, or persons, or activities, and that we all suffer alike. On that account we find that our Institute is suffering just the same as other activities, whether national, state, local, social, or what- ever it may be. Our attendance is light or, that account. We all know when times are hard we have to stay at home and watch things closer than when they are good. And when they are good we feel that the machine will run of its own momentum and in this way we can get away to see what is going on in the world. When times are hard we have to stay at home and look after everything from day to day and hour to hour.

Jan 1, 1931

The following is the list of those who have become charter members of the Rocky Mountain Coal-Mining Institute COLORADO Adamson, W. H., mine examiner, Leyden Coal Co., Leyden. Addison, Herbert, vice-president, Big Horn Collieries Co., Denver. Allen, Carl A., assistant professor of mining, Colorado School of Mines, Golden. Alley, Gerald, chief draftsman, Fuel Department, Colorado Fuel & Iron Co., Pueblo. Anderson, A. E., Denver. Arnott, John, superintendent, Colo¬ rado Fuel & Iron Co., Crested Butte. Babcock, C. W., Denver. Ball, Joseph, Walsenburg. Bayles, F. P., superintendent, Car¬ bon Coal' & Coke Co., Cokedale. Beach, Benjamin, superintendent, Colorado Fuel & Iron Co., Coal Creek. Beere, W. J., pit boss, Victor-Ameri¬can Fuel Co., Maitland. Berryman, Charles. H., secretary¬treasurer, Southern Superior Fuel . Co., Denver. Beuchat, Charles, Pryor. Bickerton, Richard, mine foreman, Colorado Fuel &. Iron Co., Tabasco. Bortman, John, miner, Colorado Fuel & Iron Co., Pictou. Bock, Henry, Box 1602, Denver. Bostwick, Fred H., Wellman-Seaver¬Morgan Co., Denver. Bowen, James V., Denver. Bowie, Alexander, general manager, Juanito Coal & Coke Co., Bowie. Bowie, Wallare D., Bowie. Breen, J P. Walsenburg. ,Brown, D. W., vice-president, Rocky Mountain Fuel Co., Denver. Bullock, W. H., salesman, Westing¬house Electric & Manufacturing Co., 1152 Gas & Electric Building, Denver

Jan 1, 1913

PRESIDENT PRYDE: I am sure we have all listened with interest to the presentation of this subject. Anything that promises economy in coal mining today is welcomed by all of us. We will now have a discussion on this paper. If any of you gentlemen want to ask any questions, you may do so. I think we will develop something of interest and along the lines of economy. That is the first consideration of a coal mining man. MR. H. D. RANDALL: It is an interesting fact that in manufacturing we find the greatest economy results from giving a man the simplest possible act to perform, while there is nothing too complicated for a machine. If we want to put up a set screw we find it cheaper to let one man set it up and the other screw it in. The maximum economy is what we are after. Similarly, one of the points of greatest interest which Mr. Ickis has emphasized, is that this automatic equipment not merely dispenses with a manual operator, but also performs certain functions which the operator cannot do. It provides an inherent protection to the apparatus and service not possible under manual operation. We very rarely have cases of failure with these automatic equipments, .and consequently have the advantage not only of having eliminated the operator's salary, but also his mistakes. We have had a large number of these equipments in use for several years, so that their practicality is now thoroughly proven, and the trend of practice now indicates that the automatic idea will be further extended and will become universal for such classes of service. MR. D. C. McKEEHAN (Union Pacific Coal Company) : My notion of an automatic sub-station is one that does not necessarily require new equipment beyond the control equipment; so that any of you that are interested in it can take up with the manufacturers and find out how much it would cost to change any equipment. The greatest point I think is the fact it eliminates the several nationalities from operating the set, either on day shift or night shift. They can so lock the control as to make it impossible for anyone to start or stop it, except the one who has the authority. Another point I do not believe was brought out very clearly: It would be particularly advantageous to people who buy power, and if you could have several sets in parallel, it would allow you to start the shift with one set and cut in the additional sets as the shift progresses. There are various operations that stop at the end of each shift, and-one or two or three sets can be cut out, leaving the load on one set, providing the size of the copper is sufficient to supply all the points of the mine. Another point I want to bring out: In case you have quite a number of sets distributed along transmission line, the switch trips, the operation restores the service, and you may have several hundred-or in case with us, we would have several thousand-K. V. A. of Motor Generator Sets and Rotaries, that would be starting at once, and the switch would automatically trip out again. MR. RANDALL: Another form of control was described as the so-called supervisory control. This control could be started up so the starting would not be synchronous, but could be spread out over a sequence. MR. McKEEHAN: I think that is rather a theoretical consideration for coal miners. They are standing at the controller ready to shut it off unless there is some selective method of starting various sets- MR. RANDALL: I had in mind this supervisory control, one man, a central operator who would determine which station should start and he would take time enough to have his load come on gradually. He would not permit all the installations to come on simultaneously, but come on in succession: MR. McKEEHAN: You misunderstand me. Suppose we had the main switch at Rock Springs, which supplies several camps, and there are several

Jan 1, 1924

The seventh Annual RMCMI Mine Rescue Evaluation was held during the 1998 Institute convention at the Silvertree Hotel, in Snowmass Village, Colorado. The Mine Rescue committee, co-chaired by Becki Boam and Elliott Tsosie, is one of 18 committees of the Institute. In 1998 a record number of 10 teams participated in the program. The teams were from the four western states of Montana, New Mexico, Texas and Wyoming and were comprised of about eight members each. Teams participating were BHP-La Plata Mine, BHP-Navajo Mine, BHP-San Juan Mine, all from Farmington, New Mexico; Bridger Coal Company, Rock Springs, Wyoming; General Chemical, Green River, Wyoming; Jacobs Ranch Mine, Gillette, Wyoming; Powder River Coal Company-North Antelope/Rochelle, Gillette, Wyoming; Sabine Mining, Hallsville, Texas; Solvay Minerals, Green River Wyoming, and Western Energy-Colstrip, Montana. The professional evaluators provided challenging scenarios for over 90 participants and many observers. The evaluators were: Art Saenz and Tom Bass of Western Environmental Associates, Keith Mitchell and Jim Jennings of Emergency Services Detail; Mary Bailey of Mary Bailey Associates; and John Peleaux of Innovative Access. Teams are not given advance warning of what the problem will entail. They are provided the necessary details when they arrive at the scenario location and work to resolve the problem in an effective and efficient manner. [ ] Seven participants made up each team with an . eighth member as an alternate. Team trainers and other mine personnel traveled with the team from scenario to scenario providing support and encouragement. The teams were presented with four scenarios each day, involving High Angle Rescue, Low Angle Rescue/Medical, Hazmat, and Confined Space. All of the victims, except for one, were provided through the cooperative efforts of the Snowmass Fire Department, who also assisted with providing several evaluators. Snowmass Fire Department is to be commended for providing over 20 victims/evaluators each day to facilitate the evaluations. Training sessions were held Friday afternoon and Saturday evening to help the teams prepare for the scenarios. A swap meet was held Friday evening for teams to trade hats, shirts, belt buckles, stickers, etc. All mine rescue participants and spouses and registered families attended the Bar-B-Q on Sunday evening followed by an adult dance. [ ] Front row: Ray Blaisdell, Solvay; Gary Rasmussen, General Chemical; Spencer Thompson, Sabine; Jack Ervin, Western Energy. Back Row: Ken Kellywood, BHP Navajo; Jonathan Sorrell, BHP LaPlata; Elton Stanton, Jacobs Ranch; Travis Roy, Powder River Coal; Ron Neff, BHP San Juan; Steve Whaley, Bridger. Sponsors who contributed to the 1998 program financially were: Blue Mountain Energy, (Deserado Mine); Flanders Electric Motor Service, Inc.; Rocky Mountain Electric Motors, L.S.; and Western Environmental Associates. Glass trophy cups, with an etching of a Mine Rescue figure and the RMCMI Logo on cherry wood bases, were presented to the 10 team captains at the Monday Mine Rescue Awards Breakfast. Eight of the ten teams had a proficiency level of 3 and 2 teams achieved a proficiency level of 2.

Jan 1, 1998

By C. A. Allen

When the writers were asked to prepare a paper on this subject for this meeting of the Institute there was some question in our minds as to what to say that would be of interest to the members. You all know that Utah has some wonderful seams of good coal, on which have been opened some of the most modern mines in the United States, and that her coal operators have been putting forth many efforts to reduce losses due to accidents as well as disease. While I believe that the physical condition of Utah's mines is as good as in any other state we are not unaware of the fact that a great deal can still be done and we are always willing to frankly discuss the accident situation in the state. Dr. Murray has assembled some interesting figures showing the monetary loss due to accidents and disease which I will will proceed to give you to show the necessity of continued efforts in welfare work regardless of humane considerations.

Jan 1, 1922

PRESIDENT WHITESIDE: If the chair may be pardoned, he would like to say he knows something of the work of this committee, and I assure you that they have all worked faithfully and hard, holding meetings at least every other day, and sometimes oftener, hustling money and going through all the different work necessary to bring about and to make a successful occasion of this kind, and I-who really acted as an outsider and viewed their work-was certainly appreciative of their efforts, and I know you would have been had you been able to see how hard they all worked. One of the sad things in life always is when one becomes a "has-been." I have been more or less active in the work of the Institute ever since its in¬ception. Just why the high honor of President was conferred upon me I have never been able to fathom, but my time is about over and I am about to join the "has-beens," and while the position naturally has entailed a certain amount of work, it has been very pleasant work, and when one has the hearty co-operation of his fellow workers, such work is always a pleasure. It is, therefore, with a certain amount of regret that I lay down the gavel and take it up again to present to my successor; but in doing so, I wish to thank you, one and all, for your very hearty help and co-operation, and to wish my successor, Mr. George B. Pryde, all the possible success that can be his. Mr. Pryde. (Applause.) MR. PRYDE: I will make no extended speech at this time. I think possibly the next year I will have enough opportunity to do that; but I had a letter from my friend, Murphy, before this meeting, and he thought we were going to have a very good meeting; but I don't know the motive behind his letter. (Laughter.) I remember the story about the Scotchman who went to see the doctor, and the doctor said: "Sandy, you drink any?" "Oh, yes." "Well," he says, "you have got to cut that out. Do you smoke?" "Oh, yes; I smoke a great deal." "Well, you will have to cut that out also." And Sandy picked up his hat and started for the door. "Wait a minute, Sandy; you haven't paid me for my advice." "Yes, but I am not going to take your advice." (Laughter.) But I am deeply appreciative of the honor you have conferred upon me, electing me to be head of this Institute for the next year. I have belonged to this Institute, I should say, ever since it has been organized. This present session especially has been a very good session. As I look back over the different meetings, I think this one stands out among all the others in the papers presented and the spirit of co-operation that prevailed among the members here, and I am not going to ask your co-operation during the year; I am sure I will get it from all of you. I want to thank you for the honor conferred upon me. (Applause.) MR. WHITESIDE: The retiring President did not quite follow the reading of the by-laws, I think, in which it says that immediately after the election of a new President, the new President shall assume office, and I got so busy I forgot all about that. The committee which the chair decided to appoint is as follows. This is to formulate safety rules: For Utah, John Crawford, William Littlejohn; for Wyoming, Peter Patterson, Glen Knox; for New Mexico, William Risdon, Allan French; for Colorado, James Dalrymple, J. C. Roberts; and last and surely not least, as chairman of the committee, Mr. George B. Pryde. (Mr. Pryde later appointed D. Harrington as a member-at-large.) C. M. GODDARD: Mr. Chairman, we all realize that in a gaseous mine the application of, safety measures transcends everything else. Machinery is installed 100 per cent safe, as they might say, to take care of any condition

Jan 1, 1923

[Adams, Douglas K General Electric Co., P.O. Box 2331, Denver 1, Colo. Adams, Kenneth L Peabody Coal Co., 301 N. Memorial Dr., St. Louis, Mo. 63102 Ahlborg, William Joy Mfg. Co., 1400 17th St., Denver, Colo. Allen, Dr. Harry C U. S. Bureau of Mines, Washington, D. C. 20242 Anderson, Robert Mine Safety Appliances Co., 1881 West N. Temple, Salt Lake City, Utah Archer, Bryan J., Jr Peabody Coal Co., 421 Glenwood St., Grand Junction, Colo. Arentzen, E. M W. RD 1, Charleroi, Pa. Arentzen, L. E. Lee-Norse Co., 6030 55th Pl., Arvada, Colo. Arentzen, Rolf F Lee-Norse Co., Box 582, Charleroi, Pa. Arnston, E. K Standard Oil Div. American Oil, Rt. 1, Box 504, Golden, Colo. Artis, Cliff E Big Horn Coal Co., 247 Sherman Ave., Sheridan, Wyo. Atchison, Lee Atchison Construction Co., Drawer D, Aztec, N. Mex. Audin, Clement, Jr Champion Coal Mining Co., Paonia, Colo.]

Jan 1, 1969

[ ]

Jan 1, 1997

The third session of the Rocky Mountain Coal Mining Institute was called to order by Edward G. Fox, President of the Bitumious Coal Operators' Association, Washington, D. C., at 9:M A.M. He stated he had enjoyed being present at the Institute the past two years, and was honored to be asked to preside at this morning's session. Mr. Fox introduced Cloyd M. "DOC" Smith, Vice President of World Mining Consultants, Inc., Washington, D. C., whose talk, "World Trade in Coal" was illustrated with a number of graphs. (See Index.) M. E. "Shorty" Wade, Assistant Purchasing Agent, Kaiser Steel Corporation, Fontana, California, was introduced and gave a paper on "What Is Required to Realize Profits Through Purchasing." (See Index.) Mr. Fox suggested that all members take an active part in their association. He stated that much more can be done in association work than as a lone wolf. He urged all to support their organization and stay with it. It is for each member's good and not for the good of a few. Carl G. Schilbe, District Manager, Jeffrey Manufacturing Company, Columbus, Ohio, was introduced, and he presented a paper on "Results of a Study in Belt Idler Design -The Perma-Seal Idler." This paper was illustrated with a number of slides. (See Index.) "Operation of A-C Mines," was the topic covered by W. C. Painter, Service Engineer, Joy Manufacturing Company, Price, Utah. (See Index.) Each of the papers was well received, and presented a number of things valuable to all who heard them. Mr. Fox then turned the meeting back to President von Storch who read several announcements of committee meetings, and the meeting was adjourned at 11:30 A.M. for an afternoon of recreation before the banquet and dance that evening.

Jan 1, 1958

Presiding: Herman Van Houten, Senior Marketing Counselor, Joy Mfg. Company, Pittsburgh, Pa., and John A. Reeves, Vice President, Mid-Continent Coal &Coke Co., Carbondale, Colorado. The Keynote Speaker, Senator Jennings Randolph from West Virginia, was unable to come due to pressing business in Washington. A film presentation on Surface Mining and Reclamation, "Energy Bridge," Courtesy of Pittsburgh & Midway Coal Mining Company, Denver, Colorado, was shown and was prefaced by comments from James V. Fisher. "Advantages of Longwall Mining in Western Coal Production" was a paper presented by David W. Wisecarver, Supervisory Mining Engineer, U.S. Bureau of Mines, Denver, Colorado. Mr. Wisecarver graduated from Virginia Polytechnic Institute in 1949. After two years with International Harvester and two years in the U.S. Army, he joined the engineering staff on a Bureau of Mines underground mining operation in Virginia for eight years where he saw duties as mine surveyor, shift boss, and assistant maintenance superintendent.

Jan 1, 1977

George B. Brennan, Secretary-Treasurer, Imperial. Coal Company, Denver, Colorado, opened the third session of. the Sixtieth Regular Meeting of the Rocky Mountain Coal Mining Institute at 8:30 a.m., and introduced the first speaker of the morning with the following remarks: It is a pleasure to welcome you here this morning. We are indeed fortunate to have such excellent speakers this morning, some of the outstanding people in the mining industry. I know I express the feelings of the entire RMCMI when I say thanks to these excellent speakers for all of the time and trouble they have taken to prepare such talks and come here to give these presentations of some of the more modern developments with which we in the coal mining industry are concerned. The first speaker this morning is going to give a paper on a subject which has only recently caused one or two of unfortunate accidents. It hadn't, prior to this, been considered such a serious problem. However, the. Bureau of Mines is hot on the trail to insure there will be answers to this previously somewhat unrecognized difficulty.

Jan 1, 1964

The Tuesday morning session of the Rocky Mountain Coal Mining Institute was opened at 9:00 a.m. by Bob von Storch, in the absence of the President. Mr. von Storch appointed the following new members to the Resolution Committee in the absence of three of the members: Albert Keenan, E. S. O'Connor and Howard Crandell. This committee was asked to be ready to report at the Wednesday morning session. Mr. von Storch then introduced Lyman Fearn, State Mine Inspector for the State of Wyoming, who presided over the morning session. Mr. Fearn introduced the first speaker for the morning, Louis A. Engstrom, Engineer at Kemmerer Coal Company, Kemmerer, Wyoming, who delivered a talk illustrated with slides in the absence of Mike Zakotnik, Jr., who was unable to attend. (Please refer to the index for printed text of this paper.) The next paper, "New Horizons -Coal for the Steam Plants of the West," was delivered by Don Newberry, superintendent of the Castle Gate Mine of the Independent Coal and Coke Company, Castle Gate, Utah, in the absence of W. J. O'Connor. (Please refer to the index for printed text of this paper.) Bob von Storch then introduced Edward G. Fox, President of Bituminous Coal Operators' Association, Washington, D. C., who delivered a paper on "A New Era in Labor Relations."

Jan 1, 1957

By L. C. Clare

In a meeting of this kind where everyone present is connected with or engaged in coal mining, and where each one is present with the set purpose of learning new thoughts or ideas, the subject of the saving of life by any method in the industry is a vitally interesting and important one. On the cost per ton basis, it mounts to a formidable figure especially so during these days of depression and stagnant, or no business. But entirely outside of the human side of the question, to lose lives would cost more than saving them. Your insurance under haphazard safety measures would mount, loss of time due to accidents would impair efficiency among employees and the breaking of the morale of the staff, due to criticism of lax methods would cost more than an efficient safety program. Taking it for granted that most of you are looking at the question from the viewpoint of a yearly or five-year cost sheet, and that at this time you are doing all that can be done without bringing a ruinous cost upon your companies, I can offer only one suggestion: Raise the quality of your safety, or lower the cost. In this meeting, there should be no question of standing still or retreating in the quality of safety, so I will amend the suggestion with "Raise the quality and lower the cost." We have learned that when the coal beds were forming, nature sealed them in with a strata of mud that the ages have turned to shale, sealing them effectively against the deteriorating influences of the air. Mudite is carrying out nature's plan of coal preservation to the inside of the coal mine. Text books teach us that a large proportion of the vegetation that forms our present coal beds grow on what might be termed mud, later falling and being buried practically where it grew by mud, then on being subjected to heat, pressure and time, was changed to coal. The mud being subjected to the same three forces forms our present shale stratas. Now if nature saw fit to use this solidified mud as a preservative through countless centuries, isn't it reasonable to expect that occasional coatings on the ribs and roofs of entries and rooms will aid materially in preserving our coal and coal dust? Nature took mud and formed it into shale; mudite takes the shale, reduces it into dust, adds water and makes a mud, applies it to the ribs, roofs and floors of the mine in a thin coating

Jan 1, 1925