Search Documents

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By K. H. Johnston

This guide was written to furnish the coal industry with a description of techniques, instruments, and clues on how to find abandoned oil and gas wells that have penetrated coal seams. The report includes specific information on searching techniques currently in use by several coal mining companies, gas-transmission companies, and waterflood operators, as well as information on State agencies responsible for the enforcement of laws and the preservation and distribution of data pertaining to the drilling, development, and abandonment of oil and gas wells. Comparative tests were performed with several commercial electronic metal detectors to determine the feasibility of using them to aid in the search for abandoned wells and to determine the instrument most suited for that particular use. The role of methane detectors to locate abandoned wells is described, including a case history. Tests were made to develop an efficient procedure to follow in systematically searching an area for metallic clues or hydrocarbon evidence to abandoned wells. The guide describes, in detail, a search sequence, including the collection of basic data, preparation of the selected area, and the physical search. Methods are given for evaluating the results.

Jan 1, 1973

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By L. J. E. Hofer

THIS BULLETIN analyzes and summarizes research at the Bureau of Mines dealing with the preparation, properties, and reactions of iron carbides in the period 1948-60, part of which was sponsored by Wright Air Development Laboratories. The objective was to develop better catalysts for the synthesis of methane and higher hydrocarbons from hydrogen and carbon monoxide. The investigations resulted in the first adequate characterization of epsilon iron carbide, which later proved to be an important intermediate in the tempering of martensite in steel. At temperatures near 170° C, the carbon in carbon monoxide reacts nearly quantitatively with finely divided alpha iron to form an iron carbide in which the metal atoms occupy the positions of the close packed hexagonal arrangement with lattice parameters of ao=2.754 A and co=4.349 A. The carbide has a composition within 2 atomic percent of that required for the formula Fe2C, a Curie point of about 370° C, a specific magnetization of 160.4 ergs per gauss-gram Fe at 50° C, and a ferromagnetic moment of 1.70 Bohr magnetons. Epsilon iron carbide can be converted to chi iron carbide by thermal treatment at 343° C for about 70 hours. The chi iron carbide so formed has a Curie point of 247° C, a specific magnetization of 142.5 ergs per gauss-gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 5.5 Bohr rnagnetons per iron atom. Direct synthesis of this carbide from carbon monoxide at 240° C indicates a composition within 7 atomic percent of that required for Fe2C. Chi iron carbide can be converted to cementite at 550° C in about 315 minutes. The theta iron carbide so prepared has a Curie point of 210° C, a specific magnetization of 147.3 ergs per gauss gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 3.9 Bohr magnetons per iron atom. Pure chi iron carbide reacts to form theta iron carbide by the elimination of free carbon. In the presence of an excess of free iron in intimate contact with the carbide, chi iron carbide reacts with the free iron to form theta iron carbide. The second reaction proceeds at an appreciable rate at 320° C and can be used to snythesize finely divided theta iron carbide with no free-carbon impurity at low temperatures. The ease of the reaction in the presence of free iron suggests that chi iron carbide is an intermediate in the tempering of epsilon iron carbide to theta iron carbide as it proceeds in steels. Experiments on carbon steel show that the magnetic moment of the iron atoms in martensite is about 2.2 Bohr magnetons per atom, a value approximately the same as that of the iron atoms in alpha iron. The Curie points of epsilon iron carbide, chi iron carbide, and theta iron carbide were found -in various specimens of tempered steel to be 10° to 20° C lower than normal values. This shift is probably the result of manganese in solid solution. Preparations of various compositions of epsilon iron carbonitrides show many effects of extensive isomorphism between epsilon iron carbide and epsilon iron nitride. The action of carbon monoxide on finely divided alpha iron at 400° C results in free carbon deposits containing filaments about 0.1 micron in diameter and several times as long. The filaments are characterized by nuclei of dense material located midway from each end of the filament. Although carbiding to near completion at 240° C over periods of about 300 hours produces a preparation containing no appreciable percentage of epsilon iron carbide, very brief periods of carbiding of the order of a minute result in the formation of detectable epsilon iron carbide even at temperatures as high as 325° C. The data indicate that epsilon iron carbide is an intermediate in the formation of chi iron carbide during its formation from carbon monoxide in the gas phase. Attempts to convert cementite to chi iron carbide by cold work increased the Curie point but did not change the X-ray powder diffraction pattern.

Jan 1, 1966

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Donna L. Anderson

This U.S. Bureau of Mines report describes a system to determine the position and heading of a continuous mining machine during the maneuvers required at the face area of a mine. The system consists of commercially available angular position sensors and a computer interface developed and tested at the Bureau. The sensors employed are laser-based scanning devices that report the angular location of retroreflective targets within their 90° field-of-view. The targets are mounted on the continuous mining machine; the laser scanners are mounted on an external reference structure. The computer interface consists of a single-board computer-controller programmed to gather and process the angular position information, and to calculate the machine's position and heading relative to the reference structure. A sensor fusion algorithm will be incorporated into the computer interface programming to increase the accuracy and reliability of the system.

Jan 1, 1989

By Joseph M. Pugliese

The Bureau of Mines through its contract research program recently analyzed the mining and environmental requirements in the premining stage for copper mining in the northern highland of Wisconsin. The Critical-Path-Method (CPM) was used in this research. However, a step-by-step derivation of the CPM Diagram was beyond the scope of this effort. The Bureau of Mines objective now is to show, step by step, how the original hand-computed CPM Diagram was constructed. The streamlining (restructuring) of this diagram from the original effort is also summarized. The critical path time (longest time) through the original CPM Diagram was 25.12 yr, excluding public liaison effort. This diagram showed the involvement of the regulatory agency, mining applicant and public in the premining stage. Analysis of this diagram produced a streamlined version which reduced the critical path time by nearly 7 yr. The CPM construction methodology offered here may be applied to mine planning for any mining operation.

Jan 1, 1983

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

By Carlton E. Brown

Sand, which is used widely under the wheels of mine locomotives to prevent slipping, is an important source of silica dust breathed by some employees of certain mines, such as those having appreciable grades on haulageways. The sand, as received, contains dust, and other dust is produced by passage of wheels of the train over the sand. Dust is disseminated into the air by such means as handling during unloading, drying, transporting, underground, sprinkling on the rails, passage of trains over Sections where sand is being or has been used, and walking over deposits of sand (or the dust thereof) on the haulageway. The disseminated dust is inhaled not only by persons in the immediate vicinity but also by others to whom the contaminated air travels. The inhalation of this must should be prevented to eliminate any possibility of the material causing silicosis (sometimes referred to as miners' consumption, miners' asthma, miners' phthiris, or miners' lung) and defined by the American Public Health Association4/ as: A disease due to breathing air containing silica (Si02), characterized anatomically by generalized fibrotic changes and the development of miliary nodulation in both lungs, and clinically by shortness of breath, decreased chest expansion, lessened capacity for worm, absence of fever, increased susceptibility to tuberculosis (some or all of which symptoms may be present), and by characteristic X-ray finding.

Jan 1, 1944

By Donna L. Anderson

The first section of this U.S. Bureau of Mines report includes a discussion of the navigational tasks performed by operators of mobile mining equipment, with the focus on the navigational information and guidance techniques required by continuous mining machine operators. Some previous research and attempts in remote and autonomous navigation of continuous mining machines are mentioned. Issues of research in autonomous navigation of various other mobile robots are presented, with attention focused on their applicability to a continuous mining machine navigating in the mining environment. Conclusions are stated on methods of automating the navigational tasks of a continuous mining machine, and a decision to concentrate initial attempts on the tasks of autonomous face navigation is defended. The second section of this report includes a presentation of the Bureau's proposed solution for autonomous face navigation of a continuous mining machine, which includes the employment of a mobile roof support as a reference for guidance in the face area, and a navigational guidance system for the continuous mining machine.

Jan 1, 1989

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications., The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939