Search Documents

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By John R. McWilliams

This report is one of a series published by the Bureau of Mines describing methods and practices at various mines throughout the United States. A previous program, conducted from 1928 to 1939, was well received by the mining industry and technical institutions and provided much source material for engineering textbooks and technical handbooks. The stringent wartime demands on the mining industry, the rapidly changing postwar economic situation, and greatly accelerated technologic growth have combined to render many of the previous data obsolete. The objective of the present program is to assemble reliable technical information on mining methods and practices throughout the country and present it for the use of the mining industry, technical schools, textbook authors, and other interested persons. This report deals with the design and development of the Berkeley open- pit mine at Butte, Mont., owned and operated by The Anaconda Company. The Berkeley pit is but one facet of a well-organized and integrated copper-mining operation involving the entire Butte district. Vein-type mining, important for 75 years, is still in progress at depths from 600 feet to nearly 1 mile; on intermediate levels, low-grade ore left untouched by earlier vein-type mines is being extracted by block caving entire ore zones,3/ and secondarily enriched but lower grade near-surface portions of the same ore zones are being mined by open-pit operations (fig. 1). The Berkeley pit itself is named for the Berkeley mine, one of the old mines that extracted copper ore from high-grade veins in the area that now will be mined by open-pit methods.

Jan 1, 1959

By R. HOLROYD

The Ludwigshafen and Oppau plants are largely independent I. G. factories situated some 23 miles apart on the west bank of the Rhine facing lannheim. The former factory is a general organic chemical works specializing in dyes, dye intermediates, plastics and synthetic rubber,. while the latter is a heavy organic chemical factory producing ammonia, methanol, higher alcohols and their derivatives. Before the war much of the I. G. research and development work was carried out at Ludwigs- hafen; in particular the high pressure research section directed by Dr. Mathias Pier played a very active part in all hydrogenation developments. Apart from the possibility that a full scale hydrogenation or Fischer Tropsch plant had been erected at Ludwigshafen/Oppau during the war, the main objectives of an oil team investigation were: - (a) To obtain from Dr. Pier and his staff an advance general picture of German fuel production processes. (b) To study the fuel developments still in the research and pilot plant stage. (c) To examine any new developments in hydrogen or synthesis gas manufacture. (d) To look for new processes for production of high anti-knock fuel constituents and for new fuel additives. (e) To investigate new chemical syntheses based on raw materials obtainable from oil. The Ludwigshafen and Oppau factories were first visited by the large team listed in Appendix A during the period 25-31st March. The investigation revealed that no large plant for synthetic fuels or lubricants had been operated at this target. All the important members of the Fuel Research Section staff had been evacuated to Heidelberg and information on the work of this department was therefore limited to that contained in seized documents, the greater part of which have still to be examined in detail. Valuable information on synthesis gas production from hydrocarbon gases was obtained as well as interesting data on a num- ber of chemical syntheses. Two members of the above team Holroyd and Faragher accompan- ied by Major Tilley (interrogator) went on to Heidelberg, contacted Dr. Pier and the chief members of his staff on April 1st and obtained from them the hydrogenation information given later in the body of the report. Later, after visiting Leuna, Holroyd, Faragher and Ellis paid a second visit to Heidelberg and to Ludwigshafen/Oppau on 27th-30th May to check a number of details, particularly with respect to hydrogenation costs, and to obtain information on the pressure.conversion of water gas to hydrogen and on the manufacture of Wickel pressure vessels.

Aug 1, 1943

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By Christopher Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940’s and 1950’s. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as “one of the great social advances of our time.” Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support’s strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, “roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization.” Yet by the end of the 1950’s, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives. The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to develop a mathematical model of cable bolt support systems. Part 1 described laboratory studies of the support properties of conventional steel cable bolts. Part 2 describes the strength characteristics of conventional cables with steel buttons, single and double birdcage cables, and epoxy-coated cables.

Jan 1, 1991

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

By M. E. Poad, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mimes monitored rock mass response to mining of an experimental underhand longwall stope in Hecla Mining Co.'s Lucky Friday Mine, Mullan, ID. This stope design, the Lucky Friday underhand longwall (LFUL), was proposed as a means of controlling rock bursting while also allowing increased mechanization of mining operations. Instruments were specifically manufactured to monitor three geomechanical factors (backfill performance, ramp stability, and rock mass response) that directly affect the success of stope design. Despite considerable difficulties with instrument installation and survival in the harsh mine environment, especially within the stope fill, sufficient information was collected to suggest that the LFUL method was successful in achieving project goals. This conclusion, in addition to favorable economic and operational evidence, led the mine to adopt the method throughout the mine. Indeed, this study and mining experience suggest that underhand longwall mining could be considered a feasible mining method for rock-burst-prone ground throughout the Coeur d'Alene District. Further Reports of Investigations (RI) in this series present in-depth analyses of the effects of backfill on rock bursting and calibration of a stope numerical model.

Jan 1, 1992

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By O. Q. Leone

Excellent metal quality, with lower power requirement, is attained in electrorefining titanium by using internal heating of the fused-salt bath. An internal heater provides more effective heat utilization, simplifies structural components in cell design, and prolongs cell life by eliminating direct application of heat to the cell container. This Bureau of Mines report covers one phase of the research in progress at the Electrometallurgical Experiment Station at Boulder City, Nev., for improving the techniques and lowering the total power requirement for electro-refining titanium metal.

Jan 1, 1959

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961