Search Documents

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By Jami M. Girard, Ed Mchugh

Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures. The purpose of this paper to discuss some of this research and to present potential new technologies for slope monitoring and design. The paper also briefly discusses various warning signs of slope instability, introduces the most common slope monitoring methods, describes the limitations of various slope monitoring systems, and presents some field results using some of this new technology.

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

By A. U. Miller

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try, if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By John H. Soulé

"INTRODUCTION The Peerless mine was examined by W. R. Storms, an engineer of the Bureau of Mines, on June 2, 1944, in conjunction with a mineral survey of the adjoining For Bayard Military Reservation. Storms again studied the mine on January 13; 15 and 16, 1945, to determine the possibilities of finding new ore reserves to replace these depleted by mining. A project to explore the Peer-less vein at depths below and to the south of the principal mine workings was proposed. Special attention was given to the possibility of exploring favorable beds in the Magdalena and Lake Valley limestones at points near the Peerless fault.The proposed project was approve and exploratory work started on January 2, 1946, and was completed on June 5, 1946. The mine was not in operation during the project, and all equipment had been removed."

Apr 1, 1947

By W. D. Ryan

Industry must be made to realize that "Safety First" means just that - safety first. The miner must realize that safety first takes precedence over earnings. The employer must realize that safety is the first consideration, and is not to be subordinated to profit-making. Neither employee nor employer is justified in adopting the principle of safety first with reservations; that is they will practice safety first only so long as they think that it does not interfere with earnings or profits. This paper proposes to demonstrate that suberdinating safety to possible profit is short-sighted and that over an ex- tended period of time it dres not result in increased profits or earnings. An employee through disregard of safe practice may receive an injury that will cause him a loss of earnings if, indeed, he is net killed or permanently in- capacitated. If permanently incapacitated any compensation he may receive is very likely to be wholly inadequate as compared with probable earnings if the accident had not cccurred. The employer, upon his part, will find that the burden of compensating his injured employse will far exceed the outlay of money necessary to maintain a reasonable program of safety in his mine or plant. The mine foreman is one of the most important factors in the matter of mine safety. A vigilant and competent mine foreman, once he has established the confidence of the employees in his ability as a foreman, can be of invalu- able assistance in promoting mine safety, for through him and his assistants the employees may be made to cooperate. Every employer should remember, then, that the soluction of the foremen and their assistants is one of the most important matters connected with the work of establishing the maximum amount of safety in his mine. Everyone connected with the mining industry must be made to realize that there is to be no back-sliding and no let-up in safety work; that no matter how dry and tedious the routine may seem it is absolutely essential and justi- fied for both humanitarian and economical reasons. Efficient safety effort pays dividends in actual cash to both employer and employee. About 50 per cent of underground accidents in coal mines take place at the working face where the miners dig and load the coal. Approximately 17 per cent of coal-mine fatal accidents are the result of underground haulage. Face and haulage accidents can and will be reduced materially if the individual miner takes all precautions necessary to protect himself and if the management

Jun 1, 1930

By Kenneth P. Klouse

The current rulemaking on mine illumination makes it necessary for mine personnel to have an understanding of the behavior of light. They must be able to understand many terms that are new to the industry and must be familiar with the use of various types of photometers. With this knowledge, the enforcement criteria for mines can be understood and compliance can be maintained.

Jan 1, 1976

This is the final report on Project CR-102 under the auspices of the Department of Environmental Resources, Commonwealth of Pennsylvania .1 The project was activated on January 5, 1970, with financial support from Bituminous Coal Research, Inc., the Pennsylvania Coal Research Board, and the Water Quality Office of the Environmental Protection Agency (WQO-EPA)2 through Grant 14010 EST to the Commonwealth of Pennsylvania Work on the project was conducted according to the procedures outlined in BCR Research Program Proposal RPP-164R, dated April 24, 1969, and a subsequent Revulsion of Scope, dated February 25, 1970. This report covers the entire project period from January 5, 1970, through March 25, 1971.

Jan 1, 1971

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 3 Principle Program Nomenclature The principal variable names used in the computer program are defined below. The following dimensions are applicable, unless otherwise indicated. Distance - Ft Velocity - Ft. /Minute Time - Minute

Jan 1, 1976

By Maria I. De Rosa

The U.S. Department of Energy Pittsburgh Research Center2 conducted experiments with mine conveyor belt samples in a 20-L furnace and in a laboratory fire tunnel to measure and compare the major toxic gas concentrations evolved during the combustion of the materials. The toxic gas concentrations, measured simultaneously through a multiport sampling device and treated as yield values, included hydrogen chloride (HO), hydrogen cyanide (HeN), oxides of nitrogen (NO, treated as NO), and carbon monoxide (CO). The data obtained from the two experimental systems were in good agreement. Correlations were developed for the toxic gas yields as a function of the percentage of chlorine (for HO gas), nitrogen (for HCN and NO, gases), and carbon (for CO gas) contained in the original materials. The toxic gas yields were also used to calculate a toxicity index (TI) parameter to assess the potential gas toxicity of belt materials during a fire. Furthermore, the TI and the mass loss burning rate values were used to calculate a toxicity hazard (TH) parameter to estimate the toxic gas hazard produced by a burning belt in a ventilated system. Results show that polyvinyl chloride (PVC) belts released higher HC1 concentrations because of the higher chlorine content; styrene-butadiene rubber (SBR) belts released higher CO, HCN, and NOz concentrations because of the higher carbon and nitrogen contents. The TI's, however, were greater for the PVC belts due primarily to the higher levels of HC1 produced. The fire tunnel data indicate that the SBR belts can bum with higher mass loss rates than the PVC belts, resulting in a potentially higher toxic hazard (higher TH values) even though their TI values were lower than those of the PVC belts.

By D. A. Hill

Introduction The fields of an infinite line source in the presence of a conducting half-space have been examined by Wait and Spies (1971). In any real communication link using a current-carrying cable for the transmitting antenna, the cable is of finite length. Here we examine the fields of a finite length cable carrying a constant current in the presence of a homogeneous conducting half-space. The constant current assumption is valid at sufficiently low frequencies when an insulated cable is grounded at the end points (Wait, 1952; Sunde, 1968). Here we examine both surface and buried cables since both downlink and uplink communication links are of interest. Also, we examine both frequency and time solutions since either CW or pulsed communications may be used. Finally, it is necessary to include both magnetic and electric field solutions since reception could be with either loops or dipoles. Since the finite cable solution is more complicated than both the infinite line source and the short dipole solutions, we explore under what conditions a cable appears to be either infinitely long or very short. Some special cases, such as- the low frequency limit, permit analytical solutions which exhibit the dependence on various parameters, such as cable length, quite clearly. Frequency Domain Subsurface Fields The geometry of a line source of length 2[l] located on a conducting half-space with the observer in the half-space is shown in Figure 1. The fields

Jan 1, 1973

By Samuel R. M. Burton

This Bureau of Mines report describes a method for determining parts per million (ppm) of helium-4 (He-4) in helium-3 (He-3) to an accuracy of ±5% by mass spectrometry. Gravimetrically prepared primary standards were used for the calibration of a Dempster 1800 magnetic sector mass spectrometer. A comparison between a 2.49% He-4 in hydrogen mixture and a 2.49% He-4 in He-3 mixture shows that He-3 can be replaced with hydrogen as a diluent for standards with comparable mass spectrometry sensitivities for He-4. Using hydrogen as a diluent allows analysis of He-3 samples for He-4 when He-3 for preparation of standards is not available and also conserves the rare He-3 isotope. Standards of He-4 in Hz were prepared for calibration of the mass spectrometer for quantitative determinations of He-4 in the 2-to 100-ppm range. A minimum detectable limit of 2 ppm He-4 is obtained by this method.

Jan 1, 1989

By Lloyd A. Morley, Alan M. Christman

General A review of the literature has revealed important areas which should be investigated during the field work. Of the utmost importance is the safety of mine personnel. Should a phase-to-ground fault occur on a shovel or other piece of equipment, current may return to the substation through the machine's contact surface with the mine floor, thereby raising the frame above ground potential and posing a shock hazard to anyone who touches the equipment. If the frame-to-earth resistance is very low, then no dangerous potentials will be developed, and a basis for elimination of the ground conductors from trailing cables could be postulated. However, should the contact resistance be high, then lethal voltages could be present on the machine frame. In this instance, low-resistance ground conductors in the trailing cable would be a necessity. Therefore, field tests should include measurements of the earth resistance of electrically operated portable or mobile mining equipment such as shovels, draglines, and drills. When the electrical distribution system is subject to lightning discharges, the grounding grid must safely carry to earth and dissipate enormous current surges. It is essential that the grounding grid have a low value of earth resistance, because any potential developed across the grounding grid as a result of current flow will appear on the frames of all machinery connected to the grid. Thus, an earth resistance

Jan 1, 1976

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By J. Whyatt

A package of bench design programs is being publicly released by the National Institute for Occupational Safety and Health (NIOSH). These programs are designed to provide a probabilistic estimate of the likelihood that various widths of catch bench will be retained. Program modules address the mechanisms of plane, plane step path, and wedge failure. Results are drawn from statistical and geostatistical descriptions of fracture characteristics and other input parameters, and reported as the statistical chance that a given width of catch bench will survive, that is, that a catch bench will remain wide enough to catch rolling and sliding material and prevent such material from posing hazards to miners operating below. The capabilities and application of this software are demonstrated through a case example. Comparing bench width estimates obtained using geologic data with actual widths is a key step in verifying that a program is appropriate for particular site conditions and that proper statistical descriptions of fracture parameters for that site have been developed. Such verification efforts improve confidence, and hence usefulness, of this method for designing future slope benches. Development and release of these programs appears particularly timely given recent progress in photoanalysis methods, which promise to greatly reduce the cost of collecting fracture data.

Jan 1, 2004

By H. H. Clark

The term "explosion-proof," as applied by the Bureau of Mines to an electric motor, refers to a motor inclosed by a casing so constructed that an explosion of a mixture of mine gas (methane) and air within the casing will not ignite a mixture of the same gas surrounding the motor. There are two classes of motors so constructed: First, a totally inclosed class built strong enough to withstand high internal pressures and so designed that the efficiency of all inclosing covers can be satisfactorily maintained; second, a class provided with relief openings or valves designed to relieve the pressure of an explosion within the motor casing and to cool any products of combustion dis- charged through the valves. A satisfactory motor of the first class is much more expensive to build than an equally safe motor of the second class. For this rea- son, attempts to make motors explosion-proof have been confined chiefly to motors of the second class.

Jan 1, 1912

This study presents a reservoir modeling approach to investigate the relative effects of different coalbed parameters on the migration of methane into development entries. A base coalbed reservoir model of a three-entry development section, where grids were dynamically controlled to simulate the advance of mining at a constant section advance rate, was created and calibrated for a Pittsburgh Coalbed mine in the Southwestern Pennsylvania section of the Northern Appalachian Basin. The values of coalbed parameters were varied to evaluate their effects on predicted methane emissions for various development distances. The results of these parametric simulations were then used to derive linear expressions relating these parameters to methane emissions into the workings. These models were analyzed to assess their significance and adequacy for predictive purposes. This work shows that coupling reservoir simulations with linear modeling yield a technique that can be applicable to different coalbeds. The reservoir parameters used by the linear models (coalbed thickness, pressure, sorption time constant, Langmuir parameters, permeability) can be determined by running relatively simple laboratory tests, such as adsorption equilibrium and permeability determination, on coal samples obtained either from the mining operation or from the exploratory boreholes drilled ahead of mining.

Jan 1, 2008

The notion of wayfinding, as conceptualized by planners, geographers, and psychologists, denotes the ability of an individual to move from one point to another through physical space. In order to achieve this movement, a person relies on a cognitive map of spatial representations [Passini 1984]. Which features of this cognitive mapping will be stressed depend, in part, on the researcher's perspective. A planner, for instance, would tend to emphasize the effect of physical structures on mobility. A psychologist, on the other hand, might focus on individual differences in how human minds encompass and represent physical space [Evans et al. 1984]. There is yet another dimension to wayfinding that needs consideration, and it rests upon the idea that reality, as experienced by human beings, is mediated: "[People] have preselected and preinterpreted this world by a series of commonsense constructs ... which help them find their bearings in their natural and socio-cultural environment and to come to terms with it" [Schutz 1967]. These "common sense constructs" are arrived at socially and constitute the agreed-upon schemas that guide people's everyday activities. According to this principle, cognition is governed by some nonlogical factors that reflect not only individual procedures but collective ones as well. These group strategies, which are shaped by shared rules and values, influence "the information gathered, the ways it is processed, the inferences that are drawn, the options that are being considered, and those that are finally chosen" [Etzioni 1992]. From this perspective, cognitive maps, rather than being individual-centered templates of environmental images [Rovine and Weisman 1989] or representations of spatial relationships [Evans 1980], are partially group-centered schematic processes. As such, they are subject to reinterpretation, revision, and outside intervention [Kaplan and Kaplan 1982]. As intermediaries between the environment and behavior, cognitive maps serve as bases for decision-making. Traditionally, it has been assumed that good maps facilitate correct decisions, which in turn leads to optimal performance during wayfinding [Hunt 1984]. Given the argument that there is a social (non¬cognitive) facet to cognitive mapping, however, this image of a cognitive map as some sort of static reference construct that motivates individual action is too narrow and mechanistic. If cognition involves less a knowledge of the environ¬ment than it does the process of "giving it meaning through imposing an order on it" [Rapoport 1976], then wayfinding behavior is not j ust a function of setting and individual differences, but is also a function of one's "normative-affective" structure [Etzioni 1992]. Rapoport [1976] used such an assumption as the base for a set of hypotheses about the connection between "external demands" and "organismic factors." One significant assertion deriving from Rapoport's ideas is that environmental

Jan 1, 2000

By Todd M. Ruff

A training software package for new mine employees, called Miner Training Simulator (MTS), has been developed by researchers at the National Institute for Occupational Safety and Health. MTS is a computer-based tool that allows a trainee to enter a simulated mine and interact with his/her surroundings in order to learn basic mining concepts, safety procedures, mine layouts, and escape routes. The training simulator software and instructions for its use are described in this report. Also, each mine using the software will have different requirements with regard to safety training. To customize the simulator for these differences, an interpreted scripting language is used to define interactions between the trainee and the virtual mine and objects in it. The scripting language, called Tool Command Language, uses simple commands to control various actions in the simulation, such as sounds, safety messages, hazards, and movement of objects. The basics of the scripting language are described here, along with many examples and instructions for building a script for MTS.

Jan 6, 2001

By A. Dale Marcy, Pamela L. Drake

Workers who perform routine welding tasks are potentially exposed to fume that may contain manganese. Manganese may cause respiratory problems and is implicated in causing the occurrence of Parkinson-like symptoms. In this study, a field colorimetric method for extracting and measuring manganese in welding fume was developed. The method uses ultrasonic extraction with an acidic hydrogen peroxide solution to extract welding fume collected on polyvinyl chloride filters. Commercially available pre-packaged reagents are used to produce a colored solution, created by a reaction of manganese(II) with 1-(2-pyridylazo)-2-naphthol. Absorbance measurements are then made using a portable spectrophotometer. The method detection limit and limit of quantification (LOQ) were 5.2 mg filter-1 and 17 mg filter-1, respectively, with a dynamic range up to 400 mg filter-1. When the results are above the LOQ for the colorimetric method, the manganese masses are equivalent to those measured by the International Organization for Standardization Method 15202-2, which employs a strong acid digestion and analysis using inductively coupled plasma-optical emission spectrometry.