Search Documents

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1985

The results of a Feasibility and Design Study of Surface Impregnation Equipment to be used for Chemical Stabilization of Coal Mine Structures are described in this report. The study was sponsored by the United States Department of the Interior, Bureau of Mines, under Contract H0210055. This program was undertaken as an essential part of the Bureau of Mines Chemical Ground Stabilization Program. The responsible prime contractor was The Eimco Tunneling and Mining Machinery Division of the Envirotech Corporation. The Rocketdyne Division of the North American Rockwell Corporation performed part of the feasibility study and design and testing of the metering and feed system as a subcontractor to Eimco.

Jan 1, 1972

By J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) slip along steeply dipping faults and (2) fracturing of strong strata above, or below, the coal seam. Both failure modes produce dynamic or ?shock? loads on the perimeter (roof, rib, floor) of mine openings. Special consideration should be given to these failure modes in planning of deep coal mines since their occurrence is not within the professional experience of many contemporary workers, and their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

By J. E. Chilton, C. R. Carpenter

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro- chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1- to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light- emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 1992

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

To inexpensively monitor the ventilating airflow anywhere in underground working places. The Approach: The Bureau has developed a small self-contained monitor which sounds an audible alarm and energizes a flashing lamp if air velocity decreases below normal. How It Works: The sensing element of this inexpensive monitor is a thermistor, which is self-heated by a constant-current electrical source. Airflow over the thermistor increases heat removal and lowers the thermistor temperature. Since the electrical resistance of a thermistor is a function of temperature change, the voltage across it varies with temperature, and, therefore, the air velocity. Changes in the voltage across the thermistor are amplified, and can be used to trigger the alarms.

Jan 1, 1975

The optimum situation in sealing the soil with latex would be to locate the sealant at the depth where natural permeability is lowest, and to narrow distribution of the latex to a film. To ascertain how closely we were achieving these objectives it was necessary to devise a method to measure the concentration of latex in soil. A number of methods were explored and two were used in actual field tests. SBR latex tagged with c14 was prepared and used to determine the distribution of polymer in the soil. The latex was made by copolymerizing a mixture of radioactive and normal styrene with butadiene in bottles by conventional methods. Average particle size was 600 Å. Diluted aliquots had 1.40 microcuries radioactivity per gram of latex. Tagged latex was mixed with soil in a range of proportions from 0.01 to 0.25% by weight to develop a calibration curve. Analyses of soil in the laboratory and from the field were determined by comparison with this master curve. Styrene-containing polymers have a characteristic peak at 700 cm-1 but crosslinked SBR is not soluble in solvents normally used in infra-red spectroscopy, e.g., carbon disulfide. We developed a method for solubilizing the crosslinked polymer by stirring overnight at room temperature a soil sample in chloroform with t-butyl hydroperoxide and osmium tetroxide. The filtered chloroform residue was dried to constant weight, thoroughly mixed and pressed into a KBr pellet, and concentration was determined by measuring the absorption at 700 cm-1. Details are given in an Appendix.

Jan 1, 1972

By Fred N. Kissell

In This Chapter [Early indicators of a gas problem How the methane hazard is reduced Ventilation principles for gassy tunnels Monitoring for gas Eliminating ignition sources and The all-important human factors component] This chapter gives guidelines for preventing methane gas explosions during tunnel construction. Emphasis is placed on assessing the hazard potential, on ventilation principles, and on monitoring for gas. The chapter also emphasizes the importance of human factors in reducing explosion risk. Ensuring safe conditions is much more than just good engineering design. It also involves the every-day vigilance of those working underground. This does not imply that the engineering design can be ignored, only that the job of providing safe conditions has just begun with design. EARLY INDICATORS OF A GAS PROBLEM For the engineer planning a tunnel project, reliable early indicators of methane are scarce. How-ever, the local geology can often provide some information.2 Carbonaceous rocks and tar sands are a likely methane source. Gas is also a distinct possibility if it is known to be present else-where in the same sequence of geologic formations. Swampy areas, sewerage systems, and landfills are also candidates because the decomposition of organic materials produces methane. The gas in a tunnel can originate in the strata being excavated, or it can migrate a considerable distance from adjacent strata. Test borings at the project site can also serve as initial indicators of gas. Methane has no odor, but may be emitted along with gases that do. If gas is emitted from the borehole, a sample may be collected by inserting a tube into the hole as far as possible and pumping the gas out. The gas sample should be collected in a sampling bag or canister for later analysis by a chemical laboratory.3

Jan 6, 2006

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 14 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFOUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS. IN ADDITION A CONNECTION HAS BEEN MADE BETWEEN THE MINE UNDER STUDY AND A SHAFT IN A WORKED OUT MINE IN THE 1 FACE AREA. THIS SHAFT IS CONSIDERED AN INTAKE SHAFT FOR THIS RUN.

Jan 1, 1977

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970

By C. B. Manula, R. L. Sanford, R. A. Rivell

Development of the Rail-Haulage Sub-assembly for the Production Sub-system (UGMHS)* required the use of ,a newly formulated model in order to best satisfy the requirements. Many of the ideas of the former single-stage rail simulator included in the original version of UGMHS have been used, together with the results of experience gained in applying the earlier model to a variety of operating situations (Sanford, 1969). The sub-assembly is developed as an independent system and, as such, can be used to analyze track systems using production distri¬butions as data input. In addition, since this model is designed to replace the original sub-assembly in UGMHS, the linking procedure is identical with respect to bi-directional information flow. The flow of coal from production sections, for example, fills the mine cars, but a condition of "out of empties" or "full of loaded" at a loading station will shut down inby production sections. A requirements analysis was conducted to determine specifically how the model could best serve the user. Operating management had the largest input in developing the following requirements for the Rail Sub-assembly: a) data input in mixed narrative - numeric form to permit user identification of the input variables; b) a user option to extract several ranges of detail in model output, i.e., an average shift summary of minimum retrieval

Jan 1, 1974

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By Dana Reinke, Launa Mallett

Interest in training evaluation in the mining industry was piqued with the promulgation of Title 30, Part 46, of the Code of Federal Regulations. Under Part 46.3, a training plan is considered to be approved if it contains certain information, including “The evaluation procedures used to determine the effectiveness of training.” The present paper is a broad overview of training evaluation and is intended to give trainers and decision-makers a framework for planning or assessing training evaluation strategies. It discusses questions to consider when starting an evaluation plan, Kirkpatrick’s model of evaluation categories, and various ways to collect data. It does not provide detailed instructions on how to develop evaluation methodologies, but reviews topics to consider when creating an evaluation plan. Training evaluation is a term that has many different meanings: assessing the quality of a course, effectiveness of materials used, teaching style of an instructor, or the comfort of a classroom. An evaluation can be done informally over lunch or with highly structured data-gathering tools. It can produce results that are useful to trainers, program administrators, corporate decision-makers, or no one. The key to a worthwhile evaluation is clearly defining why the evaluation is being conducted. Once the purpose is defined, planning the evaluation strategy can begin. For an evaluation to be effective, it should be incorporated into the development of the training activity itself. The training evaluation worksheet at the end of this paper can be used to guide evaluation planning.

Jan 1, 2002

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By P. W. Jeran

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977