Search Documents

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

By Martyn F. Roetter

The work of the operational communication systems' group dealt with a range of communication needs and functions within mines, primarily along haulageways, to and within sections up to the working face itself, and in mine shafts. A mixture of communication techniques and hardware is needed to satisfy this variety of communication needs within the differing environments encountered in U.S. mines. Substantial progress, both experimental and theoretical, has been made in recent years towards developing alternative communication systems suitable for use in mines which are based on "guided" waves, including wire-less (waveguide-like propagation in mine tunnels) and wire-based systems (leaky coaxial cables or wires) . Major priorities identified for further work needed to confirm (or deny) the applicability, and refine the operational specifications of promising communication systems for mine use include: Short-Term Projects o Cost/performance analyses of promising leaky coaxial cable and UHF radio communication systems which require further data from: - Experimental investigation under U.S. mine conditions of the performance of potentially applicable leaky coaxial cable communication systems developed in Europe (France, Belgium, and the U.K). - Cost estimates on these coaxial cable communication systems. - Measurements of UHF radio propagation in low-coal mines. - Investigation of the influence of obstacles (e.g. shuttle cars and section machinery) in the entries on UHF radio propagation in mines. o Investigation of the problems of transmitter and receiver coupling and termination matching associated with the two-way propagation of low frequency radio waves in hoist shafts.

Jan 1, 1973

By R. P. Beyer

Low-temperature heat capacities and standard enthalpy of formation of copper difluoride (CuF2) were determined by the Bureau of Mines. The low-temperature heat capacities were determined from 11 to 302 K by adiabatic calorimetry. The enthalpy of formation was determined by HC1 solution calorimetry. The standard values of entropy (S°) and enthalpy of formation (?Hf°) at 298.15 K are l8.65±0.03 cal/deg mole and -129.02±0.29 kcal/mole, respectively.

Jan 1, 1978

By Kenneth L. Cashdollar

While underground coal technology has progressed over time, regulations on coal dust have not kept up ? the most recent rules are more than 80 years old. The National Institute for Occupational Safety and Health and the Mine Safety and Health Administration conducted a joint survey recently on coal particle ranges as measured in US coal mine samples. In underground coal mines, dust explosions are prevented by the addition of enough rock dust (usually limestone) to make the total dust mixture inert. The rock dust acts as a heat sink for the dispersed dust mixture by reducing the temperature below the value needed to propagate an explosion. Federal regulations require 65% in combustible content in intake airways and 80% incombustible content in return airways, where the coal dust is assumed to be finer in size. The regulations also require an additional 1% incombustible for each 0.1% methane in the ventilating air in intakes and 0.4% additional incombustible for each 0.1% methane in returns.

Jan 1, 2008

By A. B. Hooler

"A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432. 3/The present list is a supplement thereto that includes all of the equipment approved during the calendar year 1947.The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7432 showed six air compressors on the active list; two additional compressors, Nos. 7 and 8 in this category, were approved during 1947.Items 2 and 7, unmounted loader and power unit, respectively, under Loading and Conveying Equipment, item 2, rubber-mounted mining machine and item 8, distribution box, appear in Information Circular 7432. They are repeated to show that approvals of these four equipments were extended to cover an additional voltage rating which requires material change in design.Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that are available for reducing explosion and other hazards incidental to coal mining. The present paper, with Information Circular 7432, gives the complete list of permissible mine equipment that is available under the various classifications."

May 1, 1948

By Launa G. Mallett, Charles Vaught, Michael J. Brnich

Beginning in 1991, scientists at the Pittsburgh Research Laboratory recorded interviews with individuals who are recognized as experts in mine emergency response. These 30 veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years of mining experience. Interviewees included representatives from mining companies, the United Mine Workers of America, and State and Federal agencies. Most of their comments dealt not so much with technical aspects of particular mine emergency responses, but rather the human side of more general topics, including preparedness, experience, people on-site, mine rescue teams, and decision-making. An analysis of their interviews provides an overview of lessons learned on-site at some of the largest mine disasters since the mid-1940s. This knowledge was gathered so that it could be provided to today's miners and to tomorrow's emergency response personnel. It is expected that the collective wisdom obtained can be used to help train new responders and guide those decisions that will have to be made on the scenes of future events.

Jan 4, 2004

By R. E. Head

At the microscopic laboratory of the Bureau of Mines Intermountain Experiment Station, Salt Lake City, Utah, efforts are being made to devise methods of differentially coloring finely crashed minerals as a means for their identification. Staining would facilitate sight recognition of minerals under the microscope and would be of great value in the study of crushed ores, concentrates, and tailings. Since the treatment of ores for their beneficiation is primarily based on the recovery of the minerals containing the clements of value, it is extremely important that these minerals should be known and that a method for quickly determining them when in minute fragments should be available. Herein lies one of the greatest uses for color methods. In many cases it is a difficult matter for even the trained petrographer and mineralogist to identify finely crushed minerals quickly. Although ordinary petrographic methods are accurate, they are often time--consuming and are not suitable to the needs of millmen who require, especially in the examination of tailings a method for determining minerals by inspection.

Jan 1, 1929

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

By Arthur L. Murray

"Oil-shale camps are peculiarly favored, in that before they are establishes it can be ascertained with a degree of certainty, that the life of the project is not limited. Unlike camps at metal mines, where the metal content of a given area is frequently an unknown quantity until after years of development, oil-shale camps should, from the outset, be planned and. built as permanent types of camps. Where this procedure is followed camps will be established which better serve the needs of the industry and the cost of their general care and upkeep will be less.Selection of camp or townsite.The site of the camp or town' whether on company property or not, should be selected with care. It should be separate if possible from the location of the plants of the company so as to be free from noise and fumes and so as to provide a change of environment for employees in going from their work to their homes.The principal features governing the site to be selected are as follows:Drainage. The general contour of the surrounding country should be such that drainage is away from the site. The camp or town should, if practical, be situated on higher ground than that in its immediate vicinity.Soil. The nature of the soil on which the camp or town is located may bear a decided relation to health. A porous, well underdrained top soil of at least four feet in depth insures dryness and facilities the placing of foundations and the laying of water mains and sewer pipes. Such a soil also is an advantage in growing trees, shrubs and grass plots, which are a decided adjunct to making the community attractive.Enviroment. The contiguous territory should afford no unwholesome sur¬roundings such as swamps Or accumulations of stagnant water.General Considerations. The water supply to be provided and the method of disposal of wastes influence to a certain extent the location of the camp or town-site. The means of supplying water, whether by gravity or by pupping, and the disposal of sewage, whether by outfall, system, sewage disposal system through septic tanks, broad irrigation or filter beds, or cesspools will govern the location of the site topographically in relation to source of water and point of disposal of sewage.* This article was prepared as part of the paper ""Use and Supply of Water for the Oil-Shale Industry"" by J. J. Jakowsky, to be published by the Department of Metallurgical Research, University of Utah, in cooperation with the United States Bureau of Mines."

Jul 1, 1921

By Launa G. Mallett, Charles Vaught

This report is intended to help mine safety trainers better prepare to teach the influx of new underground coal miners who are entering the industry. This is done by identifying two different approaches to instruction and discussing the ways they may affect how well prepared new hires are to deal with a dynamic and hazardous workplace. One approach is based on the use of a syllabus. Those using a syllabus are more likely to rely on lecturing or direct instruction. This is a good way to get across factual information, but does not provide a context within which miners can fit the discrete facts so that they form an integrated whole set of concepts, principles, and skills. The other approach is based on the use of a curriculum. Those using a curriculum may be more likely to help miners integrate concepts and skills that give them an overall picture of the complex mining environment and how they fit into the workplace. This will better prepare them for the decision-making and problem-solving activities that will help them work safely and productively

Jan 1, 2008

By D. A. Stanley

The Bureau of Mines has developed a simple titration technique for determining the points of zero charge (PZC) on minerals. The technique consists of titrating a mineral slurry with the potassium salt of polyvinyl sulfuric acid (PVSK) in the presence of an indicatory dye and a positively charged polymer. Values obtained by this simple method are in good agreement with values found in the literature.

Jan 1, 1982

By Kenneth L. Cashdollar

This paper is an overview of and introduction to the subject of dust explosions. The purpose is to provide information on the explosibility and ignitability properties of dust clouds that can be used to improve safety in industries that generate, process, use, or transport combustible dusts. The requirements for a dust explosion are: a combustible dust, dispersed in air, a concentration above the flammable limit, the presence of a sufficiently energetic ignition source, and some confinement. An explosion of a fuel in air involves the rapid oxidation of combustible material, leading to a rapid increase in temperature and pressure. The violence of an explosion is related to the rate of energy release due to chemical reactions relative to the degree of confinement and heat losses. The combustion properties of a dust depend on its chemical and physical characteristics, especially its particle size distribution. In this paper, the explosion characteristics of combustible dusts will be compared and contrasted with those of flammable gases using methane as an example. These characteristics include minimum explosible concentration, maximum explosion pressure, maximum rate of pressure rise, limiting oxygen concentration, ignition temperature, and amount of inert dust necessary to prevent flame propagation. The parameters considered include the effects of dust volatility, dust particle size, turbulence, initial pressure, initial temperature, and oxygen concentration. Both carbonaceous and metal dusts will be used as examples. The goal of this research is to better understand the fundamental aspects of dust explosions.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By R. V. Ramani, C. B. Manula, A. Owili-Eger

MINE PROTOTYPE The prototype chosen for application demonstration is from Kingery (1960). The mine and the ventilation plan is presented in Figure 11. A new coal mine is projected with entrance by slope 1,500 feet long. Nine train entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Will it be possible to operate five units per shift with amount of air at each unit not less than 25,000 cfm? Additionally, a shop at the slope bottom will require 10,000 cfm. The problem is completely worked out using standard ventilation formulas and simple manual calculations in the above reference and is reproduced here in Appendix II for ready reference. APPLICATION In this manual, four different applications of the PSU/MVS are outlined. An article by Stefanko et al (1972), outlines how one can move from a mine map to a network for the generation of computer input. Attention is drawn to Figure 12, which is the network line diagram of the mine ventilation system in Figure 11. Note that every roadway junction has been numbered. The dotted lines represent leakage paths and the letter 'R' on a branch denotes that the split is regulated for the quantity shown. For example, there is a leakage

Jan 1, 1975

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By Dean H. Ambrose

This paper presents an approach for representing and analyzing random motions and hazardous events in a simulated three-dimensional workplace, providing designers and analysts with a new technique for evaluating operator-machine interaction hazards in virtual environments. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. The project's methodology includes human factors design considerations, ergonomic modeling and simulation tools, laboratory validation, and collaboration with a mining equipment manufacturer. Hazardous conditions can be analyzed in virtual environments using collision detection. By simulating an operator's random behavior and machine's appendage velocity, researchers can accurately identify hazards, and use that information to form safe design parameters for mining equipment. Analysts must be discerning with the model and not read more from the databases than what the simulation model was designed to deliver. Simulations provided an interesting approach to data gathering in that there was no need for live subjects and logistics - test sites and costs associated with experiments-became insignificant. Collisions versus speed, operators' size, and risk behaviors proved the versatility found in the data obtained from the model. Preliminary results show that response time significantly affects the number of collisions experienced by the virtual subject. Also simulation data suggests that more mishaps occur with hand-on-boom-arm risk behavior.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977