Search Documents

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department's Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By Dale R. Spangenberg

This Bureau of Mines Information Circular on phosphate is one of a series of minerals availability commodity directories. Nonconfidential information from the Minerals Availability Program data base covering 148 domestic and 103 foreign phosphate properties and deposits has been abstracted for use in this directory. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operational information.

Jan 1, 1983

By Michael Schmitz, Eugene Ahrenholtz, William A. Heitbrink, Jeanne A. Zimmer, Andrew B. Cecala, Ernest S. Moyer, Earle H. Andrews, Chris C. Coppock, John A. Organiscak

Many different types of surface mining equipment use enclosed cabs to protect equipment operators from health and safety hazards. The overburden removal and mining process can be extremely dusty and can cause excessive dust exposure. To study this issue, a cooperative research effort was established between the National Institute for Occupational Safety and Health, U.S. Silica Co., Clean Air Filter Co., and Red Dot Corp. in an effort to lower respirable dust levels in an enclosed cab on an older surface drill at a silica sand operation. Throughout this research effort, a number of modifications were incorporated into the drill's filtration and pressurization system, as well as in other areas, to improve its design and performance. An average cab efficiency of 93.4% was determined with gravimetric sampling instruments when comparing the outside with the inside cab dust levels on the final design. Although this study considered just one operation, the goal was to identify cost-effective improvements that could be implemented on all types of enclosed cabs to lower respirable dust concentrations. Two critical components for an effective enclosed cab system are having a properly designed, installed, and maintained filtration and pressurization system, along with a method for maintaining structural cab integrity, which allows the cab to be positively pressurized. Another important component is maintaining cab cleanliness. Although this research was originally directed toward the mining industry, it is also applicable to agricultural or construction equipment.

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Rexford D. Singer

The purpose of this study was to evaluate the current literature on the use of calcium chloride and ligninsulfonates as dust suppressants with respect to potential adverse effects on health or the environment. Calcium chloride poses little internal hazard to man and animals, but toxicity to vegetation in and around the area of application should be expected. The effects, however, should be considerably less than those observed from using calcium chloride as a road deicer. Except for trout, ligninsulfonates seem to pose little direct systemic toxicity problems in aquatic organisms, animals and man or any problem with local vegetation. Because of a greater volume of information on its use and effects, calcium chloride is recommended over ligninsulfonates.

Jan 1, 1982

By R. E. Morgan

This publication presents abstracts of articles and investigations pertaining to the utilization of fly ash. The terms "fly ash" and "flue. ash," as' used in most of the papers, refer to the ash from pulverized-coal firing collected by electrostatic precipitators or mechanical collectors. Several investigators do not define the material on which they report beyond calling it fly ash, but they probably refer to the fine material resulting from burning pulverized coal. A few of the papers report on investigations involving not only the use of fly ash but boiler slag as well. These can be identified by the title of the articles. Bibliographical information and the abstracts are arranged according to the date the papers were published, with the most recent listed first. With the continually increasing use of pulverized-coal firing, profitable disposal of the fly ash is becoming a problem of greater importance to many utility and industrial companies. Also, in recent years, the public demand for cleaner air, and the more highly efficient fly-ash collectors available have resulted in the collection of a greater percentage of the fly ash produced. The solution to better utilization of fly ash has, therefore, been the object of research for some years.

Jan 1, 1952

By O. C. Blade

In its general study of crude petroleum, the Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the major producing Yields in the State. ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. The study was via e under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines, Whishington, D. C., and N. A. C. Pith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and. Under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.

Jan 1, 1939

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975

By O. C. Blade

[In its general study of crude petroleum, tic Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the producing fields in the State ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. No study was made under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines Washington, D. C., and N. A. C. Smith, supervising engineer, Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt senior petroleum engineer Bureau of Mines, Bartlesville, Okla.]

Jan 1, 1939