Search Documents

By John R. Reeves

The development of an new industry, which must prepare its marketable products at or near the source of the raw material, and ship them to a market which may cover half a nation, is more or less influenced by a number of natural and cultural conditions such as (1) location of plants with respect to a large market, (2) climatic conditions, (3) transportation facilities, (4) labor supply, and (5) water supply. An effort is made in this pager to give in detail a number of the more important of these conditions as they affect, either favorably or unfavorably, the development of the oil-shale resources of southeastern Indiana. The utilization of the New Albany formation for the production of oil will be similar to a large scale low-grade ore proposition in which the raw material can be obtained in very large quantities at a relatively low cost. It appears, therefore, in considering the value of this shale or its economic position in relation to other oil shales, tie cost of mining and preparation for the retort are of prime importance.

Jan 1, 1923

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By A. M. Cummings

During August 1943, the Bureau of Mines undertook sampling and measuring of the Kennedy zinc tailing pile near Hazel Green, Lafayette County, south-western Wisconsin, as part of a general investigation of this lead-and zinc-producing area at a time when it was extremely important to increase the production of metals for the Nation's War program. The tailing pile was the residue from old jigging plants that treated ore from the Kennedy mine, one of the oldest and. largest mines in the district. Because retreatment of tailing by modern milling methods was proving economically successful at other sites in the southwestern Wisconsin field, the Bureau?s investigation was designed to assist the potential operators in evaluating the feasibility of a retreatment operation at this site. The study involved measurement of the tailing pile and sampling by means of auger to determine the average metal content within the narrowest possible limits. A total of 46 auger holes ranging in depths up to 40 feet and aggregating 886.5 feet of bore were drilled in the tailing pile, and weighted samples from each hole were analyzed and averaged to determine the zinc and iron content of the tailing.

Jan 1, 1949

By Richard A. Thomas, Charles D. Litton, Kenneth E. Mura, Harry C. Verakis

Experiments were undertaken to evaluate the flammability of typical noise abatement materials used to line the cab interior of mobile mining equipment. The experiments were conducted using three different experimental configurations: 1. A ventilated tunnel test. 2. A full-size cab test where the interior surfaces were lined with the sample material and then ignited near the floor using a methane-air burner. 3. Standard ASTM E-162 tests using a radiant panel test apparatus. This paper describes the tests and presents the results obtained for 15 to 20 different materials of various chemical compositions and thickness. With one exception, materials that did not exhibit flame spread in the tunnel test also performed well in the full-scale cab test. All materials that had passed only a small-scale flammability test, such as SAE J369, failed dramatically in all three of the above test configurations. With one exception, all materials that performed well in the full-scale cab test had flame spread indices < 25, based upon the ASTM E-162 results. The lone exception had an ASTM E-162 flame spread index of 68. With regard to samples that failed the full-scale cab test, the carbon monoxide levels within the cab reached lethal concentrations in the range of 1.8% to 3.8% within 2 minutes from ignition of the sample—dramatically illustrating the severe fire environment that can result within the cab space.

Reduce costs of surface mine reclamation by improving scaper operating efficiency and reducing tire costs. Approach The Wheel Slip Monitor senses and compares the peripheral speed of a scraper&apos;s four tires 10 the true ground speed of the scraper, and alerts the operator if any of the tires exceeds a predetermined amount of slip. This system helps scraper operators reduce wheel slip during the loading cycle, thereby improving the loading efficiency of the scaper and reducing tire wear and damage. How It Works The system consists of five ultrasonic doppler velocity-sensing devices for measuring the speed of each wheel as well as the true ground velocity (see photograph). Each sensor produces an electrical output signal having a frequency proportional to the speed of the tire or terrain. The signals are conveyed through electrical cables to a control box in the operator&apos;s cab where they are converted to voltages proportional to individual wheel speeds (see photograph). The signals are further processed to activate a blinking red light, corresponding to any individual wheel which is slipping, and to sound a beeping tone that is audible to the scraper operator. The rate at which the light blinks and the tone beeps is proportional to the degree of slip. Alerted, the operator can take corrective action.

Jan 1, 1985

Reduce longwall equipment transfer time between panels by utilizing a predriven recovery room, and thus eliminate the premove preparation associated with most equipment recovery methods. Background and Approach The recovery point for a retreating longwall is a predetermined position near the end of the panel where mining is terminated and equipment is disassembled and removed. However, to prepare for equipment removal at the recovery point, bolting and wire meshing arc required before the recovery point is reached. Usually, preparations for equipment recovery begin about 35 ft from the recovery point, significantly impeding the normal rate of advance of the longwall and, consequently, production. Recently, BethEnergy Mines, Inc., and the Bureau of Mines cooperated to evaluate the applicability of utilizing predriven recovery rooms to improve longwall equipment recovery. A predriven recovery room is an entry driven parallel to the longwall face at the end of the panel, having standard dimensions (for that particular mine) and supported with bolts, wire mesh, and supplemental support. The preparation of this entry is completed before it experiences mining-induced effects from the approaching longwall face. This enables the face to continue to mine at its normal rate of advance until the panel is completed. The supplemental support is required to control the loads imposed by the front abutment and is the most vital component of the recovery room.

Jan 1, 1989

By Tobias W. Goodman, Joseph Cervik

This Bureau of Mines report investigates the horizontal trajectory of boreholes drilled in coalbeds using the rotary drilling technique. Test holes drilled in coalbeds showed that the path of a borehole in the horizontal plane depends on drilling assembly configuration, drill bit rotation, and coalbed geologic features. An assembly that contained an 18-ft (5.53) long drill collar and two centralizers had the best horizontal stability evidenced by trajectories that deviated less than 16 ft (4.9 m) from a target at 1,000 ft (305 m). Removal of one of the centralizers resulted in a loss of control of hole trajectory in the horizontal plane. Generally, holes tended to turn to the right, presumably because of right-hand rotation of the bit. Deviations from the original bearing line were as much as 200 ft (61 m) or more at a depth of 1,000 ft (305 m).

Jan 1, 1988

By T. A. Sullivan

Research undertaken by the Bureau of Mines in 1938 has resulted in the development of titanium from a laboratory curiosity to a commercial metal. Along with processes for producing the metal, it was necessary for the Bureau to develop methods for analyzing the metal, raw materials, and intermediate products. Some of the methods developed have been published.3 4 5/ General Services Administration (GSA) was responsible for purchasing titanium metal under Defense Production Act contracts with commercial producers. GSA designated the Federal Bureau of Mines to analyze this metal and establish its compliance with Government specifications. A substantial quantity of tin was found in some of the samples analyzed, and in July 1957 tin was added to the list of impurity elements to be determined. The specifications limited the amount of tin in titanium sponge to a maximum of 0.10 percent. A program was immediately initiated to investigate methods and techniques for determining tin in the range of 0 to 1.0 percent. A method accurate at the 0.10 percent level was necessary, as this level was the critical range for acceptance or rejection of the metal.

Jan 1, 1960

By Bernard Porter

The rate of the heterogeneous reaction between high-purity uranium metal and uranium tetrafluoride in molten lithium fluoride was measured. The apparent heat of activation for the reaction is 16.91 kilocalories per mole of UF4. A surface-controlled mechanism is suggested in which UF4 is adsorbed on the uranium metal surface. Additional UF4 reacts with the adsorbed species and the metal site to form an activated complex that decomposes to the product UF3. The reaction is an important source of metal loss in the electrowinning of uranium metal.

Jan 1, 1966

By A. E. Raddatz

The Bureau of Mines has determined the electrochemical rate of anodic dissolution of vanadium metal in a VC12-VC13-NaC1 electrolyte at 860&apos; C for the purpose of elucidating the reaction mechanism. Rate measurements were carried out with the help of specially designed equipment capable of continuously recording the weight loss experienced by a cylindrical vanadium anode immersed in the molten salt electrolyte while a constant current is maintained through it. The rate is expressed as a function of current density and VC13 concentration, and the reaction is interpreted in terms of an adsorption mechanism. Multiple regression analysis of the data gave the following rate equation: Rate x 104 (g.cm-2.sec-1) = -0.38 + 2.64 current density (amp-cm-2) + 0.69 log, (mole-percent VC13).

Jan 1, 1974

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

To cost-effectively reduce noise and vibration in newly manufactured mantrip vehicles. Approach Previous Bureau of Mines research demonstrated that noise controls could be in-stalled on existing mantrip vehicles, thereby substantially lowering noise levels inside the mantrip. Under Bureau sponsorship, a manufacturer of mantrip vehicles agreed to incorporate similar noise controls into a new vehicle during manufacture. Throughout this project, durability, maintainability, and cost were considered to be as important as noise reduction. How It Works The following noise-control features were included in the new mantrip: (a) Suspension Isolation- The suspension components were isolated by inserting elastomeric materials between them and the vehicle frame.

Jan 1, 1982

By Lon Santis, Scott Deitchman, John A. Decker

This report describes three cases of carbon monoxide (CO) poisoning in a manhole, including one fatality, from CO migrating through soil after nearby use of explosives. A municipal sewer project involved installation of new pipes and manholes. Work of the general construction contractor was interrupted when a subcontractor detonated 265 pounds of nitroglycerin-based explosive 40-60 feet south of the manhole to break up underlying rock. A construction worker who descended into the manhole 45 minutes after the explosion collapsed within minutes, and two co-workers descended into the manhole to rescue him. One rescuer retrieved the unconscious worker, and the other rescuer died in the manhole. All workers had elevated carboxyhemoglobin levels. In the subsequent NIOSH investigation, air monitoring was conducted with real-time instruments, and air samples were collected in Tedlar bags. Laboratory analyses of the bag samples collected near the bottom showed 1905 parts per million (ppm) CO, 19.5% oxygen, and 3% carbon dioxide. Direct reading instruments showed progressively higher concentrations as the sensor was lowered into the manhole. Subsequent chamber tests on sample explosive yielded 27 liters CO per kilogram detonated. Based on this value, the surface blast at the construction site may have produced about 3,250 liters (114.8 cubic feet) CO. The CO in this incident most likely was released from the nearby explosion and migrated through soil and fractured rock into the manhole. The blasting and construction industries should be made aware of this previously unrecognized CO exposure hazard associated with surface blasting. The extent of CO exposure from explosives used in construction is not known, and additional information on the extent of CO exposure must be collected. In addition, confined space entry procedures (including monitoring confined space atmospheres before entry) should be observed; CO monitoring of confined spaces in the presence of blasting can prevent future incidents such as this one.

Oct 30, 1997

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant&apos;s electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981