Search Documents

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By C. M. Frost

The hydrodesulfurization characteristics of a Venezuelan topped crude oil and a Venezuelan reduced crude oil were determined at temperatures from 740° to 850° F, pressures from 800 to 1,600 psig, and space velocities from 1.0 to 2.0 Vo/Vc/hr. Kinetic calculations showed that under these conditions the desulfurization reaction was first order with respect to sulfur and had an average activation energy of 32.5 kcal/mo1. Catalyst life tests made at 750° F, with pressures of 800, 1,200, and 1,600 psig and space velocities of 1.0 and 1.25 Vo/Ve/hr, showed that the decrease in the relative activity of the catalyst was a logarithmic function of time or volume of oil processed and the amount of vanadium deposited on the catalyst. Comparative tests made with residual fuels prepared from a Wilmington, Calif., crude oil and a Wyoming asphaltic crude oil showed that catalyst life may be extended by processing fuel oil with a low metal content, but it may be shortened by the presence of large amounts of asphalt in the feed.

Jan 1, 1971

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 Am. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

Improve the safety and comfort of operators of large mining equipment. Approach Develop an improved driver restraint system that is easy to use, reliable, and cost-effective, while providing increased protection in the event of a collision or rollover. The Novel Restraint System There are several problems associated with conventional lap-belt type restraint systems. Among these are: restriction of movement, lack of comfort, and fear of entrapment. Standard seatbelts become dirty and oily from lying on the vehicle cab floor and can ruin a driver's clothes. Some haulage equipment may not even have seatbelts available to drivers since they are sometimes removed during maintenance activities or as a result of vandalism. Recognizing a need to address such problems by providing a more acceptable means of driver restraint, the Bureau of Mines designed and fabricated a novel vest-type restraint system. The vest is designed to be worn during a driver's 8-hour shift and would be issued much like safety glasses, hard hats and safety shoes, thus becoming part of the operator's individual protective equipment and assuring that each vehicle has a restraint system when in operation. The vest-

Jan 1, 1985

By A. H. Warner

Sphalerite crystals occur sparingly in minor faults and pockets in a coarsely crystalline dolomite on the Brown-Tipton farm near Greenville in Greene County, Tenn. After several visits by U. S. Bureau of Mines engineers and U.S. Geological Survey geologists, a survey was r: the in the fall of 1944. Upon their recommendations, trenches on the Brown farm under Bureau of Mines supervision. In each case, the bed most favorable for zinc deposition was exposed. In the finished trench bottoms no zinc minerals are visible.

Jan 1, 1950

Now you know why there is concern about mine illumination. You have some idea about how the human eye works and about the problems of glare, peripheral vision, and accommodation. And you know that lighting in a mine presents special problems because of the dark surroundings and low reflectance. This chapter describes what can be done to improve conditions. This chapter begins with a short discussion about Federal Standards on mine lighting -- what they are and what is being done to carry them out. The chapter then describes different types of lamps that can be used for mine lighting, and discusses their advantages and disadvantages. Finally, the chapter lists some things that you can do personally to improve lighting, or can point out to others so that improvements can be made. The Federal Government is doing its part to improve mine lighting by establishing regulations. Lamp manufacturers are constantly studying new lamps to provide better equipment. And your company will do its part to comply with regulations. Better lights may not be here yet, but they will be soon. But in the end, you are the one who will be using the lights, and you are in the best position to see the improvements. You are also in the best position to see and tell others where further improve¬ments can be made.

Jan 1, 1976

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By G. S. McCaa

Rock-dusting is an. effective means of preventing coal-dust from propagating an explosion in a coal mine, but it will not prevent gas from igniting-explosively and with much attendant damage locally. Ventilation must therefore be effective at all times, regardless of the employment of other explosion-prevention methods, if gas explosions are to be avoided. This paper describes a gas explosion which occurred in as bituminous mine that was well rock-dusted at the point of ignition and which exemplifies the value of rock-dusting, the necessity of maintaining effective ventilation, and the need of permissible rock-dusting machines receiving power from a permissible locomotive. Description of Explosion The mine in which this explosion occurred is developed on a panel system in a practically level seam; the panel entries are driven in pairs, and the air current intakes on the right entry and returns on the left entry. Near the mouth of the intake a door is placed to control the ventilation; board stoppings are placed in crosscuts, except the second from the face, in which a brattice cloth curtain is hung, the last crosscut is left open and line brattices conduct the air current from the last crosscut to the faces. In No. 7 entry the last cross-cut was 152 feet from the face, the line brattice being within 38 feet of this face, and the second crosscut was 250 feet outby the face of the back entry or return. Seven days prior to the explosion the intake and return entries were rock-dusted to within 38 feet of the face, and as the entry had advanced during the week, the rock-dusting was to be extended.

Jan 1, 1929

By John R. Bartels, Dean H. Ambrose, Richard C. Wang

This paper presents the results of a study to verify and validate a computer model that represents and analyzes motions and hazardous events in a simulated three dimensional workplace. The purpose of the computer model is to support research that is investigating the safe speed range for the vertical movement of roof bolter boom arms to reduce worker injuries in underground coal mines. The information obtained for this paper is based upon a project that is investigating means to reduce workers risks of injury from exposure to mining machinery. The methodology being employed by the project includes human factors design considerations, anthropometric modeling and simulation tools, laboratory validation, engineering interventions, and collaboration with industry and an equipment manufacturer. The results of this study were used to (1) determine the input parameters that are unique to the mining environment and needed to develop a credible, computer-based, human-machine interactive model, (2) develop test methods to measure the required parameters, and (3) to refine the human-machine interactive computer model.

By Wing G. Agnew

The drilling and bit-sharpening practice in the southwest Wisconsin zinc district generally conforms to the procedure described herein, except at very small properties, where drill steel is sharpened by hand. Though hot milling of rock-drill bits is practiced in South Africa on some of the large-scale operations, it is seldom seen at American minus in any form. Because of the simplicity and low cost of the equipment, it was thought that a brief description might prove interesting to same of the operators in ether districts who do not have enough steel to sharpen to warrant equipping an elaborate sharpening shop.

Jan 1, 1936

By James P. Ulery

A Bureau of Mines geologic study of Pennsylvanian and Permian coalbeds in southwestern Pennsylvania was undertaken to determine the effects of coalbed geology and petrology on in situ coalbed gas contents. Data were obtained from 18 coreholes from parts of four 7.5 ' quadrangles in southwestern Washington and northwestern Greene Counties, and from a single corehole in Westmoreland County. A total of 88 samples from 24 coalbeds were collected for direct-method testing to determine gas content. The samples were also analyzed for petrographic composition, chemical composition, and vitrinite reflectance values. Corehole information was used to generate isopach maps and geologic cross sections useful in data interpretation. Results of the investigation show that coalbed gas content is related to vitrinite reflectance, but not to petrographic composition. Gas contents are also influenced by other geologic factors such as roof rock lithology and competency, and location with respect to local fold structure.

Jan 1, 1989

By E. D. Gardner

A custom gold and silver plant is one that treats ores for a fee. Usually such plants are located in mining districts and treat local ores. Ores of milling grade generally can stand only moderate transportation charges. These plants are scattered throughout the West. Most plants now doing a custom business originally were built by mining companies to handle ores from their own mires. As excess mill capacity became available ores from neighboring properties were treated, vainly as an accommodation. Later, as their own ore bodies became depleted, the mills were operated entirely on a custom basis. A few plants pull ore from their own mines only when the supply of custom ore is insufficient to keep the mill operating. Some of the present custom plants were built for custom work alone. Although built originally to treat the ores of the Golden Cycle mine, the Golden Cycle plant at Colorado Springs, Colo., soon became a custom mill and has been operating successfully for many years. It is the largest gold mill in the Western States and. treats Cripple Creek ores, from which most of its tonnage still comes. The plant is equipped to treat a great variety of ores and receives shipments from a wide area. It competes with smelters in Colorado, as it has a roasting plant to prepare sulphide concentrates for treatment in its cyanide plant. Most custom mills, however, are not adapted for more than one or two kinds of ore. Gold occurs in its ores both in the metallic state (free) and locked up in sulphides. It also occurs in a few places, notably at Cripple Creek and a few other Colorado districts, as tellurides. Mien the gold occurs in the native state, the ores is said to be free-milling and can be recovered by amalgamation. Usually, however, some subsidiary treatment is required to make a satisfactory extraction. Amalgamation generally was followed by tabling in the earlier mills; at present, flotation has replaced tables at many places. As depth is reached in raining and the workings extend below the oxidized zone the character of the ore usually changes, or, as the miners say, "it gets base". Since the advent of flotation, the average recovery of gold in base ores has been improved-greatly. Cyanidation is applied to some types of both gold and silver ores. The recovery by cyanidation is in general considerably higher than by other methods in vogue and in addition has the advantage of making a finished product which can be sold directly to the mist, thus obviating smelting charges on concentrate and discounts

Jan 1, 1935

By J. W. Paul

The tests described herein were made in the course of a series of experiments on coal-mine ventilation factors which the Bureau of Mines has beep; conducting for the past two years at its experimental mine near Bruceton, Pa. The object of the present tests was to determine the leakage of two air locks which had been placed in the experimental mine as hart of the equipment for tests on friction factors. Position of the Doors. The first or inner lock gas across the aircourse between No. 1 and No. 2 left butt entries, and forced the air through these butts. An air-measuring suction in No. 1 butt determined tae volume passing at tent point.

Jan 1, 1924

By Jack A. Touseull

The Bureau of Mines has developed a simple stereographic method of analyzing the orientation of single and intersecting planes of weakness in vertical pillars of parallel symmetry. From this method, it can be determined if planes of weakness transect the full horizontal cross section of a pillar. A major finding resulting from this method was that intersecting planes of weakness can transect the full horizontal cross section of a pillar even though the individual planes do not. This paper provides step-by-step instructions for using this method.

Jan 1, 1977

Use instantaneous sampling to pinpoint dust sources and to Improve dust control on longwalls. Approach Use a dust monitor developed under a Bureau contract. How It Works Sampling can be done by either a moving or a stationary method. In the "moving' method, the dust monitor is carried by a survey engineer walking at the midpoint of the shearer Dust levels and face position (support number) are taken during all phases of the mining cycle while the shearer is cutting. These measurements can show how changes in airflow along the face, face specific; (rock partings) and cutting sequence (cutting the wedge) variables affect dust levels. In the "stationary sampling" method, the survey engineer stands with the RAM at a fixed location on the face. As the shearer approaches, the dust level and the distance to the shearer are recorded at 10-second intervals. Typically measurements start when the shearer is 20 feet from the sampling position and continue as the shearer passes the position until it is 20 feet away on the other side. Dust profiles around the machine are obtained at several fixed locations along the face only while the shearer is cutting.

Jan 1, 1982