Search Documents

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By T. E. Sterner

A laboratory investigation was conducted to determine the applicability of the thermal oil-recovery method as a means of increasing ultimate oil recovery in the Appalachian region. The primary objective was to establish self-sustained combustion in consolidated and unconsolidated sand test assemblies saturated with various amounts of Pennsylvania Grade crude oil and synthetic brine. Tests using blocks of sandstone were unsuccessful because of sealing problems and fracturing of the rock due to thermal stresses. A combustion wave of about 700° F was propagated through the sand-oil-water packs in the linear tube tests. The high air flux used resulted in high oil consumption and rapid movement of the combustion wave through the tubes. Analytical tests on the sand pack showed that sufficient fuel was deposited during the linear tube experiments for a self-sustained combustion wave.

Jan 1, 1967

By Foster Fraas

The dielectric constant .has been frequently referred to as an important property in electrostatic separation whore the particles are in an air ambient. Hatfield (1) has studied the problem on the basis of fundamental theory, with the conclusion that separations in air dependent on the differences in dielectric constant, in conjunction with a nonhomogeneous field, are not feasible, because of the low dielectric strength of the air. Although Hatfield has made the statement without showing the calculation or data, calculated values substantiating this under certain conditions of the problem will be given in the following text. However, under other Conditions, these conclusions do not hold, and it is probable that the dielectric constant is indirectly influential.

Jan 1, 1948

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full' understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949

By Thomas M. Barczak

This report describes a study that examined load transfer mechanics in longwall shield supports as part of the Bureau of Mines research program to optimize support design and utilization. The objectives of this study were to determine the contribution of the leg cylinders and the caving shield-lemniscate assembly towards full shield vertical and hor-izontal load resistance capability and to determine how the interaction of these members affect overall shield response. Load-displacement characteristics of the leg cylinders and the caving shield-lemniscate assembly, independent of the full shield, were evaluated from controlled displacement tests in the Bureau's mine roof simulator and responses were compared with full shield responses to identify load transfer mechanics. It is concluded from this research that the participation of the caving shield-lemniscate assembly significantly affects the response of the shield support. It is likely that the caving shield-lemniscate assembly is not participating fully in current shield designs because of translational freedom in the numerous pin joints. It is also concluded that the shield will respond differently to different boundary condi-tions resulting from interaction with the strata. This report describes load transfer mechanics of shield supports and the implication of these research findings on shield design and utilization.

Jan 1, 1988

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Tapley deposit in an endeavor to find an additional source of copper. There are accounts that many years ago the property had some production; there are several old, inaccessible shafts apparently sunk on a vein in rhyolite or diabase. The waste dumps of these shafts contain considerable sulfides, chiefly pyrite and chalcopyrite. To cut the vein below the old mine workings, the Bureau of Mines? diamond-drilled five holes aggregating 1,204 feet. No significant copper mineralization was found.

Jan 1, 1950

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

By Daniel Edelstein

In 1985, ASARCO Incorporated terminated copper smelting operations and associated byproduct arsenic trioxide recovery at Tacoma, WA, although shipments of arsenic trioxide from stocks and limited production from cleanup operations continued. Imports of arsenic trioxide increased markedly as a result of increased demand for arsenical wood preservatives and the decline in domestic shipments of trioxide. Expanded world capacity more than met the increased demand for arsenic and its compounds, and prices remained unchanged throughout the year. Domestic Data Coverage.-Arsenic trioxide was produced by one U.S. company, which voluntarily reported its production to the Bureau of Mines.

Jan 1, 1987

By H. C. Howarth

The preliminary tests referred to in this report wore made at the Bureau's Experimental Mine under the general supervision of G. S. Rice chief mining engineer, to determine whether rock dust way be used to extinguish or control mine fires. DESCRIPTION OF THE DUST USED The dust used for application by hand was made from draw slate taken from the Experimental Mine. This draw slate was crushed in a hammer-type crusher fitted with 1/16 inch by 2-inch slotted screens. A sizing test of the dust showed 96.5 per cent through 20 mesh, 69.4 per cent through 48 mesh, 46.2 per cent through 100 mesh, end 33.5 per cent through 200 mesh.

Jan 1, 1927

By J. W. Faul

[The Bureau of Mines initiated an extensive research on coal-mine ventilation factors in 1922, large- scale tests being conducted in its experimental nine near Bruceton, Pa., over a period of two years. A comprehensive report an this work is in course of preparation, but in order to place the practical results before the mining fraternity immediately and in condenses form, the more important features will be presented in a number of short papers. The present report is the first of a series dealing with the resistance of coal-mine entries to the flow of air and considers only entries in which there are no obstructions other than the natural roughness of the ribs, roof, and floor.]

Jan 1, 1924

By R. E. Brown

The objective of this Bureau of Mines study was a laboratory-scale evaluation of the sodium sulfate refining process for removing copper from molten ferrous scrap. Maximum copper removal is achieved in carbon-saturated melts at 1,300° C. Low carbon concentrations and higher temperatures result in a less efficient copper removal and an increased sulfur concentration in the iron. Sodium sulfate refining significantly lowers the concentration of aluminum, manganese, and silicon; however, the copper removal efficiency is adversely affected by the presence of manganese and silicon. Compared with other reagents tested, sodium sulfide-forming slags were found to be the most suitable for both copper removal and sulfur control. The sulfur content of the refined iron was higher in tests conducted in acid-type refractory crucibles. Earlier studies showed that tin, a significant metallurgical impurity, is not removed by the sulfate process. During the present investigation, results showed that chlorination, using organic solid sources of chlorine, reduced the tin concentration to acceptable levels in molten iron.

Jan 1, 1975

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow,VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

By David E. Van Dillen

This volume is a task-by-task review of work performed in modernizing the BMINES finite element code. Much of the discussion is accomplished by cross reference to the user?s guide, which is Volume I of this two-volume report. The computer program described in this report provides for the static, three-dimensional, linear and nonlinear analysis of structural and geologic systems by the finite element method. The nonlinear material properties currently available in the code include isotropic, anisotropic, variable modulus, plastic, viscoelastic, and viscoplastic. Load application capabilities include gravity loading, surface tractions, and initial stresses. The element library includes rods, beams, plane and axisymmetric quadrilateral elements, three-dimensional brick elements, thick shell elements, and plane, axisymmetric, and three-dimensional joint elements. Special features include the ability to simulate excavation and construction sequences by means of element activity. An automatic mesh generator is included in order to simplify input preparation.

Jan 1, 1981

By Thomas J. Fisher, Christopher C. Jobes, Edward F. Fries

This report (Software Safety 2.2) is the third in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended or use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and non networked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety .• 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the Safety File is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be don and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treaty of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 9, 2001

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

Federal lands often contain extensive mineral resources and decisions affecting access to those lands are made with knowledge of the possible minerals-related consequences. Information is provided to the Bureau of Land Management (BLM) in this report for use in preparing environmental impact statements on the Western Mojave Management Area (WMMA) and the Desert Tortoise Priority Habitat (DTPH). To augment U.S. Bureau of Mines (USBM) efforts such as the Mineral Assessment of the Planned Foil Irwin Expansion, Modified Silurian Valley Alternative, San Bernardino County, California which is in progress, and the Economic Analysis of the Minerals Potential of the East Mojave National Scenic Area; California, the USBM studied mineral deposits and estimated the potential impacts of mining in a segment of the California desert; the 8.7-million-acre WMMA, an area which includes the 1.2-million-acre Desert Tortoise Priority Habitat (DTPH). In addition, this information is intended to assist administrators, legislators, and the concerned public in understanding the economic importance of mineral resources in the California desert, especially that portion designated as the WMMA. See figure 1.

Jan 1, 1993

By C. W. Dwiggins

The Bureau of Mines characterized the chemical and physical properties of metallo-organic materials in petroleum to determine their effect on petroleum production and refining. The structures and physical properties of porphyrins and materials that normally contain metalloporphyrins such as crude oils and asphaltenes were investigated using elemental analysis, NMR analysis, absorption spectrometry, and small-angle X-ray scattering. Petroleum fractions greatly enriched in metalloporphyrins were obtained using asphaltene precipitation, liquid extraction, and large-scale liquid-solid chromatography. Selected fractions containing porphyrins were further purified by chromatographic methods, crystallization, and demetalation followed by chromatography. Nonporphyrin metals could not be appreciably concentrated from the bulk of the asphaltene.

Jan 1, 1969