Search Documents

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By Daniel R. Walton

A study to explore the potential of utilizing the transport time required to move coal miners to and from the working sections. Consideration was given to all forms of training and presentation media, taking into account such environmental factors as noise, dynamic interferences, visibility, physical constraints, and contaminants. Indications of managements? and workers' attitudes toward man-trip training were also assessed. The final product was a proposed prototype training system for man-trip training. Includes Bibliography.

Jan 1, 1979

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By Richard A. Dick

This Bureau of Mines report describes the evolution of modern-day blasting agent and slurry products and the state of the art of the usage of these products as it exists today. The steadily increasing consumption of blasting agents and slurries at the expense of cartridged high-explosive usage is related. Although safety is not covered in depth, reference is made to pertinent safety literature available. Product formulations, detonation reactions, and detonation products are discussed. Product terminology is defined and the significant differences between the relatively insensitive modern-day dry blasting agents and slurries and cap-sensitive high explosives are described. Blasting agent and slurry properties are discussed, as well as methods of determining and describing these properties, and specific types of products are also discussed with reference to their ingredients,-properties, and field applications. Increasing consumption of slurries, particularly in small-diameter boreholes, and the development of more cap-sensitive varieties of slurries are forecast although dry blasting agents should continue to dominate the market. The consumption of cartridged high explosives will level off or gradually decrease.

Jan 1, 1972

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By R. S. Dean

[During the past fiscal year the Metallurgical Division has made important contributions along the lines dictated by the Bureau policy of conservation of domestic mineral resources through Its investigations include determining of fundamental data of metallurgically important materials improvement of standard ore-treatment method to eliminate waste and improve the grade or recovery of the products; and development o new metallurgical processes.]

Jan 1, 1940

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

A compilation of papers presented at the Fifth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on July 30, 31, and August 1, 1980. Papers cover areas of electromagnetics/power systems, power systems, monitoring and control, and communications.

Jan 1, 1980

Provide improved permanent stoppings designed specifically for use in mines with large cross-sectional entries. Approach The large entry sizes in many mines, such as oil shale, salt, and limestone, make the conventional stopping construction techniques used in smaller opening mines unacceptable. The Bureau of Mines and Colorado Mining Association jointly sponsored a contract to design and test new or modified stopping concepts for these mines. The most promising concepts were then tested in an oil-shale mine having 30-foot-high by 55-foot-wide mine entry openings. All stopping designs tested were evaluated in terms of cost, air tightness, and resistance to blast damage.

Jan 1, 1987

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959