Search Documents

By John E. Shelton

The growing interest in beryllium as a structural material, and its in-creased use in recent years for atomic energy application, have led both government and industry to express concern over the inadequacy of the beryllium resources in the United States and the free world. Contemplated and proposed uses for this unique material will surpass the capacity of the domestic beryllium mining industry to supply raw material, which is presently extracted from relatively small deposits by hand sorting. The need for a simple beneficiation process for beryl ores has long been recognized by the Bureau of Mines, but to date no single process has proved satisfactory for treating deposits containing a sufficient tonnage of beryl ore to warrant commercial exploitation. As a part of the Bureau's continuing effort to develop an economical recovery process, this report describes flotation research on samples of beryl-bearing pegmatites from the George Roebling mine in Connecticut, and the Colony mine in New Hampshire. The study resulted in two methods of treatment to which the ores responded reasonably well.

Jan 1, 1961

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By X. Shi, V. Vallyathan, N. S. Dalai

"Using. ESR spin trapping methodology, evidence was obtained that fresh quartz dust in a cell-free aqueous medium generated hydroxyl - and possibly superoxide radicals. The hydroxyl radical generation potential decreases on storing of fresh quartz dust in ambient air and on the addition of either catalase, superoxide dismutase, desferoxamine, or DMSO. The role of quartz related radicals in the biochemical mechanism of acute silicosis is suggested from these findings.IntroductionThis report summarizes our electron spin resonance (ESR) detection of oxygenated radical formation by freshly crushed quartz particles in a cell-free aqueous medium, and its inihibition by radical scavengers. This study was undertaken with to elucidate the primary biochemical mechanism involved in the development of silicosis (Farber, 1983; Reiser and Last, 1979; Silicosis and Silicate Disease Committee, 1988). In particular the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood (Farber. 1983; Reiser and Last, 1979;). It is generally believed that the action of quartz particles on the cell membrane is the starting point of the silicotic process (Farber, 1983; Parazzi et al., 1968). Thus the surface characteristics of the quartz particles have been the subject of several recent studies (Bolls et al.. 1983; Dalai et al., 1986; Fubini et al., 1987). Recently, We reported that mechanical crushing of quartz under normal atmosphere generates free radicals which decay with time, and that these free radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to aged dust from the same stock (Dalai et al., 1986; Vallyathan et al.. 1988). The formation of Si• and. SiO--type of radicals from quartz particles crushed under atmospheric conditions has also been reported by Fubini et al. (1987). In addition, Gulumian and van Wyk (1987) have reported that quartz particles react with hydrogen peroxide (H202) to generates hydroxyl radicals (•OH) and suggested that this process might contribute to quartz's pathogenicity. However, these authors did not report the effects of metal chelators, so it was not clear as to whether the detected -OH radicals simply resulted from the Fenton reaction involving exogenous metal ion contaminants. Earlier, Marasas and Harington (1960) reported that quartz particles could function as an oxidant in a number of in vitro oxidations, including the hydroxylation of proline and lysine. They postulated that silica dusts, on reacting with water, could release H2O2 which might have the potential to react with various biological constituents and thus cause tissue damage. In fact, Gabor and coworkers (Gabor and Anca, 1974; Gabor et al., 1975) suggested that the cytotoxicity of quartz particles might be associated with the generation of some 'factor or factors possessing the properties of a free radicals capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently Weitzman and Graceffa (1984) reported that asbestos is able to catalyze the generation of • OH radicals from H2O2. Their later work indicated that lipid peroxidation may be one of the mechanism by which asbestos produces tissue injury (Weitzman and Weitberg, 1985). This is significant because • OH radicals are capable of causing peroxidation by abstracting hydrogen atoms from cell-membrane lipids and initiating lipid peroxidation in lysosomal membrane (Fong et al., 1973). In fact, the formation of oxygenated species in reactions involving quartz was suspected since Kolbanev et al. (1980) reported the detection of H2O2 in the reaction of fresh quartz particle with aqueous medium. The present work was thus undertaken to detect the anticipated formation of some oxygenated, radical species by reactions of quartz in a cell-free media and its inhibition by radical"

Jan 1, 1988

By T. OnIin, F. F. ApIan

"A study has been made of the surface properties of coals of differing ranks, in their natural state and as modified by the addition of collectors. The evaluation of their surface properties has been done by captive bubble contact angles, water and methylene iodide sessile drop contact angles, zeta potential, point-of-zero charge (PZC) shift, and flotation. .changes in the hydrophobicity of coal is a function of both the rank of the coal and the collecting reagent.INTRODUCTIONThe chemical and physical properties of a raw coal will determine its response to a given beneficiation process. .For such processes as flotation, filtration, flocculation, dispersion, handling, dust supression and agglomeration, however, it is also necessary to consider the surface properties of the coal and mineral matter constitutents of the raw coal. In the case of a specific particle to be floated, it is also necessary to consider the properties of the coal as modified by the addition of some reagent designed to modify (usually increase) the hydrophobicity of the coal surface. General properties of the coal have been well summarized by Van Krevelen (1) and Elliott (2), while the data for the surface properties of coal are much more scattered in the literature (see, e.g.: Parekh and Aplan (3), Gutierrez-Rodrigues et al. (4), Aplan (5), Arnold and Aplan (6), Hogg and Chander (7) and Rosenbaum and Fuerstenau (8)). While a knowledge of the inherent surface properties of a sample are important, of much greater practical significance are the properties of the particle in the presence of a reagent, such as a collector, designed to enhance the hydrophobicity of the particle. This study will focus on the surface properties of coals of various ranks in the presence of a variety of collectors."

Jan 1, 1989

By Kyei-Sing Kwong

The U.S. Bureau of Mines investigated the synthesis of advanced ceramics (SiC+AlN, SiAlON, SiC+A1203, and Si3N4+AlN) from natural clays (kaolin, halloysite, or montmorillonite) by an intercalation and heat treatment method. This process includes the steps of refining a clay, intercalating organic chemicals into its layered structure, drying the intercalated mixture, firing the treated structure at certain temperature ranges in controlled atmospheres to form desired compounds, and grinding the loosely agglomerated structure. Focus of this research is to economically process advanced ceramic structures from abundant natural resources. The advanced ceramic phases produced in this simple treatment are homogeneously distributed at the nanostructure level, and may potentially lead to cost effective manufacturing processes. The intercalation of clay was confirmed by X-ray and BET analyses. The evolution of chemical compositions during carbonization reactions and carbothermal reduction was investigated. The characteristics of refined clays and synthesized powders were studied. Advanced ceramic composites/solid solution have been produced from intercalated clays, without the presence of other compounds.

Jan 1, 2010

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By James S. Browning

The Bureau of Mines conducted laboratory batch and pilot plant flotation tests to determine the technical feasibility of recovering commercial-grade mica from a California micaceous schist. Best results in the laboratory batch tests were obtained using sodium carbonate and sodium silicate for pH control and quartz depression, and a combination of fatty acid and cationic reagents as the mica collector. In continuous pilot plant flotation tests, an alkaline fatty acid-cationic method recovered about 70 percent of the mica in a concentrate analyzing 95.6 percent mica.

Jan 1, 1965

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

By K. E. Tame

As part of a Bureau of Mines survey of radioactive waste disposal , a laboratory investigation was made to study such problems in carbonate leaching mills . Because uranium concentrators employing carbonate leaching with caustic precipitation normally recycle barren solutions to the washing circuit , the disposal of liquid radioactive wastes is automatically controlled . However , it was deemed important to determine the actual radium 226 concentrations occurring in this type of milling so that the survey of the entire industry would be complete . The laboratory procedure consisted of leaching the ground ore at 85 ° to 90 ° C and 50 pct solids for 6 hours in a sodium carbonate - sodium bicarbonate solution . The pulp was filtered to obtain a pregnant solution that was reacted with sodium hydroxide to precipitate the uranium as sodium diuranate . Regeneration of the barren solution was accomplished by gassing with carbon dioxide . The solution then was reused by advancing the solution through the washing to the leaching operations . The radioactivity in the pregnant solution was unusually high , averaging 6,500 disintegrations per minute ( dpm ) of radium 226 per liter . However , over 95 pct of the radium was precipitated with the uranium . Consequently , no buildup of radium occurred upon reuse of the barren solutions for washing .

Jan 1, 1964

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By K. K. Kershner

The purpose of this investigation was to develop methods on a laboratory scale for recovering tin from metallurgical slime, Tin chlorides were volatilized using mixtures of hydrogen chloride and reducing gases, such as hydrogen, carbon monoxide, hydrogen sulfide, ethane, propane, and butane. Optimum conditions were found to be n mixture of 3:1 of hydrogen and hydrogen chloride at 475° C. Over 95 percent of the tin was volatilized as chlorides. Low temperatures and relatively rapid rates of reaction are distinct advantages of the chloride volatilization process. Research is being continued with various slimes and will be extended to tin ores, where the method offers interesting economic possibilities in comparison with current tin-smelting practice.

Jan 1, 1957

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

By Phillip R. Moyle

A basic precept in mineral exploration is that the best places to prospect are where minerals have already been found. The California desert has many old mining districts once thought to be "played out" that are currently producing more mineral wealth than at any time in the past. Because no "crystal ball" exists that will enable us to predict the Nation&apos;s future mineral needs, land management plans must be flexible enough to respond to these often unforeseen needs. MANAGEMENT ISSUES The California Desert Conservation Area (CDCA) (figure 1) encompasses 25 minion acres, nearly one-quarter of the total area of California. Passage of the Federal Land Policy and Management Act of 1976 (FLPMA) launched an intensive program by the Bureau of Land Management (BLM) to study this vast area. Painstaking scientific investigations were made of wildlife and plant populations, soil, air, and mineral resources, range use, and wilderness characteristics, among other environmental concerns.

Jan 1, 1992

By D. Harrington

Near the close of the nineteenth century electricity was introduced underground, and the mining industry automatically was confronted with another potential source of fatalities and injuries to mine workers. Electricity has become an increasingly vital factor in the production of goal, particularly in recent years, because of the greatly extended mechanization that has taken place underground. The enlarged use of electrical equipment for cutting, loading, and hauling coal unquestionably increased the potentiality of shock and explosion hazards underground. Electricity may be used in coal mines with minimum danger if electric equipment and power-carrying wires are chosen properly and installed and kept protected by proper safeguards; on the other hand, if vigilance is relaxed in the slightest degree accidents may result. Electrical accidents are caused chiefly by direct contact with electrical equipment or power-carrying wires, by ignition of explosive gas or dust, and by fires of electrical origin. Electricity now ranks fourth as a cause of coal-mine fatalities, not including deaths from explosions or fires of electrical origin.

Jan 1, 1936

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980