Search Documents

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau's Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By R. Stefanko

In this report, the use of Penn State Ventilation Simulator (PSU/MVS) for planning and evaluating new coal mine ventilation systems is demonstrated. The simulator's application to evaluate the ventilation system of a coal mine currently under development is discussed. The ventilation system is evaluated for representing development of the mine at the end of 12, 24 and 36 months after mining has begun. The report describes the necessary steps of data input preparation, ventilation network development, analysis of results, modifications to the network, and methods to expand the computer program for networks larger than 550 branches.

Jan 1, 1977

By Les A. Beckett

The Bureau of Mines has developed MULSIM/BM, an improved computer program using the boundary-element approach for geomechanical analysis of mine plans in single or multiple coal seams. This Information Circular presents the improved features of the MULSIN/BM program. The four major improvements are the following: (1) Ability to specify up to 26 material property sets. (2) A new material model capability for gob and inserted materials such as packwalls or cribs. (3) Ability to model a large area with a grid of undivided blocks and to subdivide only a specified fine-mesh portion of these blocks into elements. (4) Specification of extraction ratios for the undivided blocks. In addition, an interactive graphics mesh generator program was written to accompany MULSIM/BM. A complete user's guide and program listings are included within the appendixes. The MULSIM/BM and mesh generator programs are available on tape from the National Technical Information Service.3

Jan 1, 1988

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By Lloyd G. Fitzgerald

"The dangerous nature of explosives makes them a potential hazard wherever they are used, but they are likely to exercise their greatest harmfulness under conditions inherent in coal mining. The ease with which explosives can be detonated and the suddenness and violence with which they detonate require great care in their handling and use, if acci-dents are to be avoided. Campaigns have been waged by the manufacturers, the Federal Bureau of Mines, coal-mining companies, and other agencies to educate users of explosives in their dangers and in their proper use and care.Probably 95 percent of the explosives accidents can be attributed to poor judgment, carelessness, negligence, or chance taking. In many explosives accidents it is difficult to determine the cause definitely, as the evidence of the origin is destroyed by the blast and frequently those involved have been killed. Survivors of the accident often are of little help in determining the cause, as the accident occurs so suddenly they cannot tell what happened or prefer not to divulge the information they have because it may point to their own carelessness.A survey has indicated that about 10 percent of all fatalities in coal mines were caused by explosives accidents (excluding gas and dust explosions initiated by explosives). A list of explosives accidents by States, from 1925 to 1932, classified according to the severity of the accidents, indicated that Kentucky and Wyoming had the greatest number of fatalities resulting from explosives accidents. Records of the Bureau of Mines show that 14 coal-mine explosions occurred from January 1 to June 1, 1943. Explosives were involved in four of these explosions. Black powder caused two of the accidents and permissible explosives used in a nonpermissible manner the other two. These statistics are mentioned to show that explosives are still causing severe accidents.Elimination of the hazards associated with explosives begins on the surface. Storage magazines should have no opening, except for entrance and ventilation; ventilators should be screened effectively to prevent the admittance of sparks as well as to prevent unauthorized entrance. The interior should be kept clean and dry, and the floor should be of nonsparking material with no metal exposed. The surrounding area should be kept free of combustible material for not less than 25 feet (and preferably 50 feet) in all directions. Storage magazines should be fire-resistant and reasonably bulletproof."

Aug 1, 1944

8186. Aquilina, C. Determinazioni relative di gravita eseguite nel 1939 (Relative Determinations of Gravity Made in 1939), Ric. Ingegn, Rome, vol. 10, 1942, pp, 6376. In 1939, the author made a survey of relative gravity in the Mediterranean-basin, 41° 35,5' to 41° 56.3' northern latitude and 0° 10,3' to 0° 28' longitude, referred to Mt. Mario. Ten stations were covered; 25 other stations had been occupied in the vicinity of Rome and in Albanian mountains during previous years. The new measurements revealed gravity anomalies ranging within the following limits: (1) With a free-air reduction, between + 29 and + 120 mgl., average + 60 mgl.; and (2) with a Bouguer reduction, between + 22 and + 87 mgl., average + 41.5 mgl. - V. S.

Jan 1, 1946

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By G. T. Krempasky

In an attempt to develop a suitable precast concrete support for underground use, two different models (1955 and 1958) of a five-piece concrete set were designed, fabricated, and tested under adverse loading conditions. Model 1955 was designed to withstand an ultimate, uniformly distributed, vertical load equivalent to what a three-piece, 12- by 12-inch wood set of intermediate-grade Douglas fir would withstand. A design figure of 138,000 pounds for the vertical load was used on both the 1955 and 1958 models. In addition, the 1958 model was designed to withstand a uniform horizontal load of 7,000 pounds per foot and additional concentrated-point loading. The step- by-step design of each model is presented in the appendixes. A series of five destruction tests was conducted underground on the 1955 model, and results of the tests showed that the type and method of blocking were of major significance.

Jan 1, 1963

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or nonvolatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this t port. Data were obtained on application of such locomotives to coal mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By Joseph H. White, DR. JAMES G. CUMMING

This report presents the results of an investigation of hookworm infection in the deep gold mines of the Mother Lode, California. In this investigation 1,440 miners of the Mother Lode have been examined for hookworm infection; 444 miners were found to be infected; and 91 miners have taken the treatment and have gotten rid of the infection. ·Within a short time after this preliminary examination, an industrial strike started, which gradually scattered the miners and made it difficult to institute the treatment of many of those who had been found infected. ·With the completion, however, of the State survey all these will eventually be identified and treated. In 1906 Dr. F. F. Sprague, of Jackson, Cal., and formerly of the Philippine Islands, recognized the prevalence of hookworm infection in the gold mines of California. He treated many cases of the infection and brought the prevalence of the disease to the attention of his colleagues. Following closely this pioneer work of Dr. Sprague was that of Dr. E. E. Endicott, health officer of Amador County. In 1911 Dr. Endicott a related his experience in a paper before the American Medical Association. In 1909, Dr. Herbert Gunn, under the auspices of the California State Board of Health, made an investigation to determine the prevalence of the disease among miners. b He reported on the blood and stool examinations of groups of men from three large mines in Amador County. The high eosmophilia verified by stool examinations in many of the cases, and the demonstration of larvae in soil from the workings led Dr. Gunn to the following conclusions: 1. Hookworm disease is endemic in certain mines of California. 2. From 50 to 80 per cent of those working in these mines are infected. 3. The infection undoubtedly is present in practically all the gold mines of California and in those of Nevada just over the border. vYhen it was definitely determined by the California State Board of Health to make an investigation, in cooperation with the Industrial Accident Commission of the State of California and the Federal Bureau of Mines, as to the prevalence of hookworm infection among the miners of California, the following procedure was planned: (1) To encourage the superintendents of the various mines to cooperate in the campaign; (2) to diagnose fecal specimens from the miners and determine the percentage of infected miners; (3) to reach an agreement with the superintendents that all infected men must be treated; (4) to make reexaminations of all treated men; (5) to issue "hookworm certificates"; and (6) to eventually reexamine all California miners. A visit to several of the mines on the Mother Lode made it evident that the mine operators would cooperate most cordially in this campaign; in fact, several superintendents had already considered the advisability of such an undertaking.

Jan 1, 1917

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982