Search Documents

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By M. H. Stanczyk

The Bureau of Mines made bench-scale laboratory tests on a sample of typical Florida phosphate slime to determine alumina and phosphate extractions obtainable by agitation leaching, by baking and curing, and by a leach-electrolysis scheme. Recovery of mineral values from leached slime pulps by resin-in-pulp ion exchange contact and the reaction of the leached pulps to filtration, flocculation, and settling were also investigated. The best extractions of alumina and phosphate were obtained by (l) agitation leaching with sulfuric, hydrochloric, or nitric acid at an elevated temperature or (2) curing or baking the slime with sulfuric acid. Alumina extractions ranged from 80.8 to 90.0 percent and phosphate extractions ranged from 93.3 to 98.4 percent when the slime was leached at 90° C with sulfuric, hydrochloric, or nitric acids. Baking the slime with sulfuric acid at 200° C for 4 hours yielded an alumina extraction of 92.3 percent and a phosphate extraction of 97.0 percent, whereas curing with sulfuric acid at 100° C for 24 hours gave slightly higher alumina and phosphate extractions. Flocculation and settling properties of the slime were virtually unaffected in all cases. Filter area requirements, although somewhat improved as compared to untreated slime, remained relatively high. The lowest filter area requirement obtained was 44 square feet per ton of dry solids treated per day. Contacting leached slime pulps with ion exchange resins depleted the leach pulps of solubilized values; however, the filtration and settling properties of the barren pulps were unaffected. A leach-electrolysis scheme resulted in some concentration of solubilized phosphorus, but the method showed little promise of being commercially feasible.

Jan 1, 1966

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By J. P. Powell

Systematic waterflooding was first tried in Washington County, Okla., in 1937, when a 40-acre project was begun in secs. 24, 29, 32, and 33, T. 27 N., R. 13 E., jointly by the Keener Oil Co. and the Phillips Petroleum Co. The property later was sold to Lee Morrison. A second project was begun in 1941 in sec. 14, T. 6 N., R. 12 E., by the Oklahoma Oil Corp. Both projects were abandoned by the end of 1942. A third project was begun in 1945 and the fourth in 1948, but 1949 actually was the beginning of intensive waterflooding development in Washington County. The results of previous waterflooding projects are described in Bureau of Mines Reports of Investigations.2 3 4/ Oil production in the county followed a similar trend, dropping to a low of 990,000 barrels in 1945, then steadily increasing until 1956, when more than 4 mil-lion barrels of oil was produced. Most of the increase in oil production is directly attributable to water injection.

Jan 1, 1957

By John I. Kasteler

The Rambler mine is in the Douglas mining district, Albany County, Wyo. (fig. 1). The property was first operated about 1870 for gold found in the outcrop of a leached ore body. Copper and metals of the platinum group were discovered, in 1900, or soon thereafter, and intermittent mining was done until 1918, when a fire destroyed the surface plant, and the underground workings caved. The mine has since been idle. The Bureau of Mines conducted a development project on the property from October 1942 to October 1943, with a recess period between November 1942 and August 1943. Ten diamond drill holes, totaling 1,859 linear feet, were drilled on the property (fig. 2). The mine dump was sampled after preparation with a bulldozer. Assay determination and spectrographic analyses disclosed small quantities of copper and metals of the platinum group in the samples. Determinations were made on 11 samples from the diamond drill holes and 23 samples from the mine dump. The assay results and spectrographic analyses are given in tables 1 and 2. The logs of the diamond drill holes are given in an appendix to this report.

Jan 1, 1949

By John R. Bitler

A computerized napping system was developed by the Bureau of Mines to provides procedures for the rapid and inexpensive display of coal reserve data. Mapping system output consists of two types of maps, point distribution and contour (isopleth), which can be produced for data (coal analyses) associated with a point location (outcrop, drill core, or mine samples). These locations can be in the form of latitude and longitude or Universal Transverse Mercator (UTM) grid coordinates. The mapping area can range in extent from as small as a single county to as large as a multistate region. The mapping system utilizes programs developed at Harvard University, in addition to several modifications developed by the authors. The primary advantage of this system is that it enables the display of a rapidly changing data base and computerized map generation without the intermediate steps of digitizing and overlaying to produce base maps. The mapping system is applicable to any regional mineral reserve or resource study for which point location data are available. Included are example maps of the distribution of data points and contouring for sulfur content of the Upper Freeport coalbed in this western Pennsylvania demonstration area.

Jan 1, 1977

To separate complex mineral mixtures according to their dielectric properties. Approach Develop a laboratory-scale continuous dielectric separator to separate mineral mixtures by exploiting their difference in dielectric properties. How it Works Dielectric separation is de-fined as the separation of particles based on their dielectric properties. The uniqueness of the Bureau's continuous separator, called the ?Rotating Drum Dielectric Separator,? is that it contains a high-voltage electrode con-figuration. The drum electrode consists of a series of coaxial parallel wires mounted on the outside surface of an Insulated cylinder. The screen electrode Is a wire mesh, quarter cylinder positioned outside and coaxially with the drum electrode. The drum electrode is placed in a liquid of dielectric constant K with the liquid level just above the drum's axis. The screen electrode is completely Immersed

Jan 1, 1981

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By Martin H. Stanczyk, I. L. Feld

Continuous open - circuit attrition grinding of a coarse commercial kaolin to produce paper - coating clay , which must have a particle size analysis of 70 percent or more minus 2 - micron equivalent spherical diameter ( esd ) , was studied by the Bureau . The coarse clay , containing about 11 percent minus 2 -micron esd material , was ground in a 10 - inch- diameter attrition grinder using continuous single- and multiple - stage grinding circuits . The clay feed rates varied from 10 to 480 pounds per hour . In some tests , the influence of varying loads of sand grinding media on particle size reduction was studied . Batch grinding tests also were made for comparative purposes . Multiple- stage grinding gave better results than single - stage treatment when equivalent raw clay feed rates were used . In the best test made , a product containing about 80 percent minus 2 - micron esd material was obtained when grinding 60 pounds of raw clay per hour using a three - stage grinding circuit . Power consumption in the test was about 318 kilowatt -hours per ton of clay treated or 475 kilowatt - hours per ton of minus 2 - micron esd material produced .

Jan 1, 1963

By L. E. Geyer

"The following list gives the title and author of various publications of the Ceramic Experiment Station, Columbus. Ohio, of the Bureau of mines, together with other ceramic publications of the bureau, which have been published in technical journals and by cooperating agencies. The list also includes the publications on ceramics which have been issued as bulletins, technical papers, or mimeograph Report of Investigations of the bureau.Papers Published in the Technical Press.The Effect of some Electrolytes on the Properties of Clays. Schurecht, H.G. Jour. Am. Cer. Soc., Vol. 1, #3, March, 1918.A Pycnometer Operated as a Volumeter. Schurecht, H.G. Jour. Am. Cer. Soc.,Vol. 1, #8, August, 1918.The Properties of some Ohio and Pennsylvania Stoneware Clays. Schurecht,H.G. Jour. Am. Cer. Soc., Vol. 1, #4, April, 1918.The Fusibility of Graphite Ash and its Influence on the Refractoriness of Bond Clay. Booze, M.C. Jour. Am. Cer. Soc., Vol. 2, #1. Jan., 1919.Behavior under Brass Foundry practice of Crucibles containing Ceylon, Canadian and Alabama Graphites. Stull, R.T. Jour. Am. Cer. Soc., Vol. 2, #3. March, 1919."

Oct 1, 1924

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

5. Development of Initial Probing System 5. 1 Introduction The preliminary evaluation of a variety of potential methods for initial probing showed that the optical system using closed circuit television (CCTV) and the sonar, or acoustic ranging, system were the most promising. The former is capable of pro¬viding a visual display of the mine passages in a clear, non-smoky environment, and the latter is capable of providing a map of the spatial location of the coal surfaces making up the entries, as well as objects, such as cribs, mining machines, etc., in the passages in both smoky and non-smoky environments. The sonar system used in conjunction with the CCTV in a clear environment can greatly assist in resolving the spatial distribution of objects seen on the TV screen. Further, in a smoky environment the interpretation of the sonar information could be facilitated if some visual information were also available. CCTV systems exist but require some modifications to suit this particular application. The Industrial Hazards and Communications Division of the Bureau has an ongoing program for the development of such a CCTV system. Rather than duplicate this effort in developing a CCTV system, it was decided to evaluate the possibility of utilizing their system for initial probing, while continuing with the develop¬ment of a system which would work in any environment, including the presence of dense smoke. The concept of using sonar for the initial probing of mine passages represents the application of new technology requiring development. The results of such a development effort undertaken during the course of this program are described in the following sections.

Jan 1, 1973

By Chas. G. Maier

The bright annealing of copper is an industrial practice of considerable importance. In connection with this process, equilibrium concentrations of carbon monoxide and dioxide, which may exist in contact with copper and cuprous oxide at elevated temperatures, are of interest. Data obtained at the Pacific Experiment Station of the U. S. Bureau of Mines enable estimates of these equilibrium concentrations to be made in two independent ways. Although the publication of final data on one method can not take place until certain further experimental work is accomplished, repeated requests which the Bureau of Minus has had for data relative to the annealing and deoxidation of copper justify the present preliminary report. This paper deals with the calculation of gas concentrations in the reduction of cuprous oxide, using more scientific data which will be published later, and refers especially to those conditions of temperature and concentration of practical implication, and from which critical limits ensue.

Jan 1, 1929

By Jr. Oitto

A polyester-type resin and deformed-steel reinforcing bars (rebars) were used in to strengthen and to stabilize bolted, fractured wall rock along pas 1:'y. in a western gold mine. Reinforcing bars were placed in boreholes drilled into fractured rock and then were surrounded by resin pumped under pressure into the holes and intersecting fractures until the wall rock was thoroughly impregnated. Pumping and injection equipment and infusion procedures are described. Visual examinations for movement in bonded and adjacent unbonded rock were made for 3 years. Fractured walls containing resin-rebar installations were strengthened. The results suggest that resin-rebar support can be used advantageously and economically in repairing fractured or broken rock when compared with rock bolting or timbering.

Jan 1, 1965

By Russell R. Trengove

The Bureau of Mines developed by core drilling the Cove Meadow copper property, also known as the Patterson property, from May 6, 1949, to August 6, 1949. It is in the Cove Meadow mining district, northwestern Humboldt County, Nev., 102 miles northwest of Winnemucca. The purpose of the work was to determine possible reserves in a mineralized shear zone in andesite that has been partly explored by several surface cuts and two shallow underground workings. Production from this zone to August 1, 1,949, was 98 tons of hand-sorted copper ore assaying 5.1 percent. The development work performed by the Bureau of Mines comprised a study of the geology, mapping the area, sampling the outcrops, and exploring by diamond drilling the shear zone adjacent to the fault. Seven holes were drilled for a total of 1,246 feet. Mineral reserves indicated by the project are confined to a length of 500 feet along the strike.

Jan 1, 1950

By Eugene T. Sheridan

The 23d annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 75 producers in 17 States re-ported commercial production of peat in 1956. Forty-seven producers reported humus production, 19 reported reed-sedge peat, 17 reported moss peat, and 1 reported muck. This total exceeds the number of active operations, but several producers reported recovering more than one type of peat. Fifty-five percent of the total production was reported as peat humus, 30 percent as reed-sedge peat, and 15 percent as moss peat. A negligible amount was reported as other types. More than one-fourth of the total output was raw peat with no preparation, other than having been air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, or kiln drying.

Jan 1, 1958

By Thomas E. Green

A solvent extraction procedure using 8-hydroxyquinoline and chloroform was investigated by the Bureau of Mines as a preconcentration technique for the determination of aluminum, calcium, cobalt, copper, iron, lead, magnesium, manganese, nickel, and zinc in large samples of high purity tungsten. X-ray spectrographic and atomic absorption methods were used to determine the trace metals after preconcentration. The presence of 10 grams of tungsten had a pronounced effect on the distribution of 8-hydroxyquinoline between the aqueous and chloroform phases. This change in the 8-hydroxyquinoline distribution in turn had an adverse effect on the extraction of the trace metals. Extraction efficiencies can also be adversely affected by an increase in the quantity of extractable metals present, as shown by radiotracer tests using 65Zn. Excess 8-hydroxyquinoline in the extracts did not interfere with the determination -of the serious interference in the combined ion exchange paper--X-ray spectrographic method. Although preconcentration by 8-hydroxyquinoline extraction was found to be partially successful, other preconcentrationn methods based on ion exchange and dithizone extraction were found to be superior.

Jan 1, 1968

By A. B. Hooker

A list of permissible mine equipment, tested and approved by the Bureau r. Mines previous to January l, i-)4, , was published in Bureau c Moines In ornation Circular 7207.3/ The l ,.t c -. that dote was complete as to equipmentthen available and in current Information Circular 7210,?+/ published as a supplement thereto, listed equipment approved during; the calendar 1942. Information Circular72x'3,_/ published as a second supplement thereto, ! listed equipment approved during the calendar year 1943. The present listis. Another supplement covering approvals issued during the calendar year 1c)44. The items are numbered crud to indicate the consecutive order in which each typo of machine or device was approved _.c?. in its particular classification. Thus Information Circular 7207 gave 1,t drills and drilling much fines on the Bureau'sactive.. d active list Ih: additional anal approval: were given in 1942 the three issued in 19 and one issued :n 1944- bring the total to `3. Item 111, under. Loading Machines and conveying appeared in lnformation Circular 7207. It is repeated ',tore to _how that on j,,l was granted Curia 1the optional of this loader when modified .'or 2 0. alt ciruits .]

Jan 1, 1945

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939