Search Documents

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

In 2007, a total of 14,871 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.4%) were sand and gravel mines, followed by stone mines (31.2%), coal mines (13.7%), nonmetal mines (4.9%), and metal mines (1.9%).

Aug 1, 2009

By Jack E. Tress

The Bureau of Mines has been involved for several years in the development of processes for the recycling of solid wastes. As part of this program, a project was initiated to determine the feasibility of producing secondary pig iron from auto scrap. During the test period, 86,000 pounds of shredded auto scrap, along with petroleum coke and fluxing agents, was charged to a submerged-arc furnace of 1-ton nominal capacity. Eighty-eight thousand pounds of pig iron, with an average carbon content of 3.90 percent and an average copper content of 0.2 percent, was produced at an electrical consumption of 512 kW-hr per net ton. A cost estimate of the process showed that the pig, iron might be produced at a cost of $57 per ton.

Jan 1, 1973

By Welby G. Courtney

The Bureau of Mines conducted an exploratory field survey to determine the amount of airborne coal dust, the size distribution of the dust, and the rate of dust deposition in coal mine airways. The survey was taken at eight underground locations in operating coal mines. The rate of dust deposition in the airways depended upon the concentration of air-borne dust and decreased exponentially with distance from the dust source. The rate was seemingly independent of the size of the airborne dust particles. The rate of deposition, along a return, for the coal dust from a fade being mined with a continuous mining machine closely matched the rate for the rock dust from a trickle duster. A sample rock-dusting schedule for that return is presented; that is, the trickle duster should be operated for 3-112 hours after every five shifts to protect the average deposit of new float coal dust in the return, but operation after every three shifts is preferred, to protect an occasional heavier deposit.

Jan 1, 1982

By Charles Vaught, Michael J. Brnich, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.2 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Underground coal miners Length: 9 questions (30 minutes for administration and 30 minutes for discussion) Skills: Mine fire escape strategies/procedures Use of emergency breathing apparatus Knowledge of sensations experienced when wearing breathing apparatus Communication Location: Underground coal mine section, average 60 inch seam height Problem: You are the section foreman on the 17 Left longwall development section at the Paula Ann No. 3 mine. The section has been driven about 4,000 feet from 4 West Mains. One of the shuttle car operators took a call from the fireboss saying that there was smoke from an unknown source coming into your section. You attempt to contact someone to find out where the smoke is coming from but get no response. You assemble the crew and start riding out of the section on the mantrip when you encounter heavy smoke. At this point, you decide to take your crew and travel on foot in the belt entry that is on a neutral split of air. After traveling about 6 crosscuts in the belt entry, you encounter heavy smoke at which time you and your crew don your person-wearable SCSRs (PWSCSR). After donning the apparatus, you and your crew continue traveling outby in the belt entry. Near the mouth of the section, one miner in the group starts to have trouble breathing from his SCSR. Because breathing resistance is increasing with the length of time the apparatus is worn, the miner is "outbreathing" the device since his oxygen requirements are greater that what the PWSCSR can supply. Although you slow

Jan 10, 1999

By R. R. Wells

An important activity of the Bureau of Mines is the continual search for new sources of minerals. As a part of the investigation of strategic mineral deposits in the United States, samples of mercury ores were submitted to the Ore Dressing sections of the Salt Lake City and Albany stations for metallurgical testing. This paper gives data summarizing the results obtained from laboratory beneficiation studies of mercury ore samples submitted during the period 1941 to 1947. Ores tested included three from Jackson County, Oreg., one from Valley County, Idaho, one from Storey County, Nev., and one from Sonoma County, Calif. In general, the ores from Oregon were not amenable to concentration by flotation because of intimate association of cinnabar with other minerals or because of extremely low grade. One Oregon ore was amenable to direct distillation provided lime was added to reduce corrosion of the retort.

Jan 1, 1950

By Fred N. Kissell

Air recirculation caused by dust scrubbers at coal mine working faces was examined by the Federal Bureau of Mines with regard to the potential hazards caused by a possible buildup of methane gas. A theoretical analysis indicated that there was no apriori way to predict the effect of scrubber recirculation on methane concentration levels. Experiments conducted in a full-scale model of a working face area indicated that methane levels were dependent to a great extent on the location of the scrubber exhaust, but that the scrubber recirculation did not substantially increase the methane concentration above those levels that would have prevailed were the scrubber not in operation. An analysis of two underground scrubber trials showed that the scrubbers had no significant effect on methane levels, and a review of explosions attributed to recirculation showed that these were characterized by a lack of fresh air as well as recirculation. It was concluded that high methane levels are due more to a lack of fresh air than to recirculation.

Jan 1, 1975

By M. J. Kovalik

The effect of oxidation by air at temperatures ranging from 200° to 390° C on the change of chemical and physical properties of Pittsburgh-bed coal was studied as a function of processing time and temperature. The goal was to prepare a nonagglomerating fuel from a strongly coking coal for use in continuous carbonizing processes and in fixed-bed gasifiers. The oxidized coal was carbonized in a bench-scale apparatus, and the coke strength was evaluated in a Roga tumbler. Strength of the coke was progressively reduced with time of oxidation until the coking power of the coal was apparently destroyed. Time requirements to obtain an essentially nonagglomerating product were inversely related to processing temperature. Gaseous products released from the coal during oxidation reduced the yield of the desired nonagglomerating product, which decreased with time of oxidation at constant temperature and with increase in processing temperature at equal time. Oxidation at a temperature slightly above the lower limit of the plastic temperature range of Pittsburgh-bed coal was most effective because of the short processing time required and moderate processing losses.

Jan 1, 1963

By D. A. Lucero, J. E. Brockmann, L. A. Mondy, K. L. Rubow, D. J. Rader

"Department of Mechanical Engineering, University of Minnesota, Minneapolis, MNExperimental and correlated stage responses (the fraction of particles entering an impactor that are collected on a stage) are presented for the Andersen Mark III and Marple personal cascade impactors. The impactors were operated upright and fully assembled so that interstage interference and wall losses could be properly studied. The observed stage responses showed maxima that fell significantly short of unity, meaning that a monodisperse aerosol is never collected exclusuvely on one stage, but is distributed among several stages and internal losses. Correlations for the stage responses are presented so that the experimental results can be used to determine size distributions with available data-inversion algorithms. Simulations with log-normal distributions show significant differences between dpa50 histograms and the more accurate distributions that result by taking the response functions into account.Cascade impactors are widely used for the measurement of aerosol size distributions; their ruggedness and simplicity of operation make them an attractive choice for a variety of environments. In one common application, the aerosol of interest is drawn through the impactor, and the amount deposited on each stage is determined gravimetrically. The primary objective is to extract as much information as possible about the initial size distribution from the resulting set of weights. Unfortunately, the reconstruction of contin-uous size distributions from finite data sets is an ill-posed problem. Not surprisingly, a variety of such reconstruction techniques are presently in use; the success of each method depends on the particular nature of the aerosol sample and the instrument response.Inversion of impactor data by any of these techniques requires that the response functions for each stage be known. The stage response function gives the fraction of particles entering the impactor that deposits on that stage. Values of the response function range from zero to one, and depend on impactor operating conditions (e.g., geometry, flow rate, and gas properties) and particle properties (e.g., diameter, density, and shape factor). As interstage interferences and particle losses will affect each stage's response, experimental determination of stage responses should be made for fully assembled impactors. Unfortunately, impactor stage response functions are rarely reported; rather, single-stage efficiency curves are given that provide an incomplete description of impactor performance.This paper presents experimental stage responses for two fully assembled cascade impactors: the Andersen Mark III and Marple personal impactors (model 298, Andersen Samplers, Inc., Atlanta, Ga.). These calibrations were performed with monodisperse liquid droplets for both impactors and also with monodisperse solid spheres for the Marple personal impactor. The calibration results for the Mark 111 impactor presented here have been previously reported in the response-function format (Rader et al., 1989). The calibration results for the Marple personal impactor, however, were originally presented in the single-stage efficiency for¬mat (Rubow et al., 1987) and have been reanalyzed in this work. Losses within both impactors are considered, and their treat¬ment within data inversion techniques is dis¬cussed. In addition, correlations for each impactor's response functions are presented so that these calibration results can be easily included in data-inversion algorithms. Size distribution inversions using these response correlations are compared with the standard cut-point method for two lognormal test dis¬tributions."

Mar 1, 1992

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By THOMAS SOULE, R. I. C. Manning

The Phelps Dodge Corporation considers safety a major operating problem , both from the humanitarian standpoint , for this company has a real interest in the welfare of its employees , and from the economic standpoint , for it has found the safe way to be the most economical . In turn , a feeling among employees that the company really has their interests at heart has a wonderful psychological effect . It is bound to bring forth more and better work and to attract and keep workmen of the better class . There is keen competition between the various branches of this corporation for a trophy that is awarded each year to the one having the best accident record . This trophy was won by the Nacożari branch of the Moctezuma Copper Co. in Mexico in 1926 and 1927 , and the Morenci branch won the trophy in 1928 and 1929 .

Oct 1, 1930

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By J. J. Burns

Disasters such as occurred at Oppau, Germany, in 1921, at Tessenderloo, Belgium, in 1942, and in this country at Texas City, Tex., in 1947 clearly indicate the explosive hazard associated with the manufacture, storage, and transport at ion of ammonium nit rate The importance and extent of the hazard may be Judged from the large amount of ammonium nitrate produced and transported annually in this country. Between July 1, 1947, and June 30, 1948, it was estimated that the United States produced 461,528 tons of ammonium nitrate commercially for agricultural purposes alone .5/ In addition, U. S. Army Ordnance plants have manufactured and shipped 779,730 tons of ammonium nitrate fertilizer to Germany, Japan, and Korea.6/

Jan 1, 1953

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By F. N. Kissell, R. J. Bielicki, J. H. Perkins

A sorption apparatus for measuring the equilibrium sorption isotherm and the rate of diffusion of methane from fine-sized coal was designed and constructed. Preliminary work that used Pittsburgh and Pocahontas No. 3 coal shows that the diffusion coefficient varies with pressure and that the fracture spacing in these two coals is substantially different.

Jan 1, 1972

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By C. A. Herbert

In summer, when hot, moisture-laden air enters a coal mine in the region east of the Mississippi River, the moisture is likely to condense on the roof and ribs because the incoming air is cooled below its dew point upon contact with the roof, ribs, and floor of the mine passageways. When the roof and ribs become wet owing to this condensation they are said to "sweat." In many mines, as soon as this sweating begins, shale or slate roof that appears solid and strong in winter begins to cut and fall. For a long time most mining men believed (many still believe) that the roof trouble was due to this sweating. However, from observation of conditions in one mine the operators concluded that the trouble was caused by expansion and contraction of the roof due to changes of temperature. This opinion was confirmed by experiments at several mines in cooling the air as it entered the mines. Methods used in these mines for cooling the air are described in this circular. MINE A At mine A the roof gave considerable trouble in the summer, and it was observed that where a spray of water from a leaking dam kept the roof wet and at a uniform temperature no difficulty was experienced with the roof, although it had cut and fallen on either side of that point. From this fact the company officials concluded that changes of temperature in the air rather than moisture caused the trouble and that if the incoming air were cooled to approximately normal strata temperature much of the additional roof trouble experienced during the summer would be overcome.

Jan 1, 1940