Search Documents

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

By John W. Buch

Upon review of German World War II mining practices and equipment for planning coal, the Federal Bureau of Mines initiated research leading to the development of a pneumatic planer for anthracite. The results of tests are reported in this manuscript. It was demonstrated (1) that hard anthracite can be planed and (2) that the design and operating requirements are within the limits of present-day engineering and technology. For hard anthracite, the depth of cut indicated is 4 to 6 inches; with a chain pull of 20 to 40 tons and the speed of planer travel of 18 to 20 feet per minute, a 40-hp. motor will be required for the planer hoist. Compressed-air requirements for the planer will be 250 to 300 c, f, m, at 60 to 70 p. s, i. It was learned that the length of the 4 individual sections of the planer should not exceed that of the individual troughs of the armored chain conveyor (5 feet in this instance); otherwise, bottom coal will be left in synclines, and the planer will override the conveyor at anticlines. Pneumatic pushers should be operated from a separate compressed-air line fitted with a pressure regulator. Results indicate that additional development work is warranted.

Jan 1, 1957

By S. E. Khalafallo

The Bureau of Mines investigated the kinetics of reduction of wustite and magnetite with carbon monoxide. A mechanism was postulated wherein the interaction between gaseous and absorbed carbon monoxide appears to be the rate-determining process. This mechanism fully accounts for the experimental rate equation JL.h relates th velocity of reduction to the pressure of the reducing gas at constant temperature. It also explains the variability of the heat of activation of the reduction process with the state of aggregation of the oxide material. The integrated rate equation is in perfect agreement with the experimental reduction-time curves.

Jan 1, 1966

By Harry Freund

Gallic acid is a sensitive, stable, colorimetric reagent for the determination of tantalum in the range of 2 to 40 µg.Ta/ml. The method consists of the fusion of tantalum oxide with potassium pyrosulfate and solution of the cooled melt in satu-rated ammonium oxalate, followed by development of a yellow complex with an ethanolic solution of gallic acid. The tantalum-gallic acid complex absorbs over a broad region in the blue and near ultraviolet. Adverse effects due to interfering ions and solution conditions, such as oxalate concentration and pH, can be minimized by a suitable choice of wave length. A new and sensitive colorimetric method is provided that has been used successfully at the Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines for determining minor amounts of tantalum.

Jan 1, 1956

By E. D. Gradner

During 1924 a number of lives were lost and other men incapacitated by the toxic effects of gases produced in blasting in massive sulphides. In one mine, three men working in a raise were caught by gases from blasting a drift round in massive sulphide on the level. The round in the drift was shot ahead of time and it was necessary for the three men to travel through the gases to the intake air course. Two of the men lost their lives, and the third was injured, apparently for life. Other men at this same mine have been caught in the gases at blasting time and seriously injured. At a second mine, the gases from blasting in sulphides appear to be very dangerous, and it was necessary to send a number of men who were caught in such gases to the hospital. One man who was seriously gassed has not recovered in over a year is time. Another man similarly gassed soon died of influenza.

Jan 1, 1926

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By W. H. Ode, W. A. Selvig

Briefly, this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties. The number of the standard profile with which the maximum cross-sectional area of the button most nearly corresponds is recorded as the swelling index. Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization, it gave indications of having value in measuring free-swelling and coking properties of coals when burned on fuel tests. An opportunity to investigate this occurred when an engineering company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal. Some of these coals gave trouble by swelling excessively and clogging the grate. Samples were obtained, and it was found that the troublesome coals gave radically higher free-swelling numbers than did the coals that performed satisfactorily. Also, it was found that the free-swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the standard volatile-matter test or iron agglutination-value results. The results of the free-swelling test were confirmed by the Subcommittee on Plasticity and Swelling, Coal, a special group of the Subcommittee, under the chairmanship of R.A. Shuman, worked along with the test method. Estberg, Limacher, and Shuman of the Battelle Memorial Institute investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential-type stokers from the swelling characteristics of the coal. Data were presented that also showed that the index was helpful in the selection of coal for industrial underfeed stokers.

Feb 1, 1948

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932

By Jos. R. Guiteras

This paper is one of o. series describing mining and milling methods and costs being published by the United States Bureau of Mines. It presents the results of a study of the Alice mine by the writer in December 1936. ACKNOWLEDGMENTS Acknowledgment is made to J. Fred Johnson, mining engineer off the American Smelting & Refining Co., for permission to visit the property; and to Arthur F. Johnson, general superintendent at the property, for his friendly cooperation in contributing the information contained in the paper.

Jan 1, 1939

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By G. M. Kintz

From 1895 to 1932, inclusive, 1,0163/ men were killed in and about New Mexico coal mines. Of these, 473 (approximately 47 percent) were killed in the 17 explosions listed in this paper. The second largest explosion of record in the United States, in so far as fatalities are concerned, occurred in New Mexico. The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the State inspector of coal mines of New Mexico. The tables included are complete only with regard to major disasters. The Bureau of Mines considers as a major disaster one in which 5 or more men are killed. A few minor disasters are included, however.

Jan 1, 1934

By G. St. J. Perrott, N. A. Tolch

"The testing of explosives for permissibility for use in coal mines was begun by the technologic branch of the United States Geologic Survey in February, 1909, and continued by the United States Bureau of Mines from July, 1910; this testing has been carried on from year to year as the explosives were submitted by manufacturers. As a result of these many years of testing for permissibility a large amount of data has accumulated regarding the characteristics of permissible explosives. The manufacturer expects a sample of explosive submitted for test to meet the requirements for permissibility, otherwise the sample would not be submitted. However, in spite of the careful regulation and preparation of the formulas a certain percentage of explosives fails to pass the gallery tests. It is therefore interesting to note the proportion of failures at the gallery for a given composition of explosive. The fact should be emphasized that this discussion deals with all explosives submitted for test, both those which passed the tests and those which failed to pass. Explosives that failed to pass the tests were never designated as permissible explosives and have never appeared on any list of explosives permissible for use in coal mines.The Bureau of Mines classifies permissible explosives in two ways, according to the quantity of poisonous gases produced and according to the characteristic ingredient of the explosive.4 In this paper only two types of the latter classification are considered, as follows:"

Dec 1, 1929

By William G. Pariseau

Elastic-plastic finite-element simulation of cut-and-fill stoping in deep, narrow veins shows substantial quantitative agreement with field measurements of stope closure and fill pressure made at two mines in the Coeur d'Alene mining district of northern Idaho. The simulation procedure, validated by field data, was used in an analytical study of vein-wall closure and sill-pillar stress as influenced by fill modulus, rock modulus, and premining stress. Ratios of closure and pillar stress in the filled stopes to closure and pillar stress in the unfilled stopes are used as prediction indices for fill performance. In general, the support capability of fill increases dramatically as the ratio of fill modulus to rock modulus approaches 1. A significant reduction in closure .from the open stope--up to 75 percent--occurs with a relatively low-quality 10-ksi-modulus fill (rock modulus of 1,000 ksi). However, a higher quality fill is needed to achieve a substantial reduction in pillar stress from that of the open stope. A 100-ksi-modulus fill reduces pillar stress in both the 36-foot and l6-foot pillars (vein width is 10 feet) by about 50 percent relative to the open stope.

Jan 1, 1976

By Robert H. Ridgway

Chromite has been produced commercially for slightly more than a century. Developed, at one time, chiefly as a chemical pigment raw material, it has subsequently found extensive application in other chemical industries - as a refractory material for furnace linings and as the sole source of the metal chromium. For some years prior to 1914, its use as a refractory predominated; but post-war development in alloy steels, principally stainless steels, enhanced the metallurgical demand in the form of ferrochrome with a consequent increase in the demand for chromite. More recently direct reduction of chromite in alloy-steel manufacture has been applied to a limited extent. Alloy steels containing varying amounts of chromium, with or without other alloying elements, now find extensive use in a ride variety of ways - in structural material, machines, industrial equipment transportation by land, sea, and air, sanitary equipment, food preservation, and a multitude of other uses. In recent years chromium plating has had wide application and has become important. industrially, but the amount of raw material consumed

Jan 1, 1936

By A. B. Hooker, P. G. Guest, E. J. Gleim

"From time to time the United States Bureau of Mines has received reports of gas explosions alleged to have been caused by correctly assembled flame safety lamps. In most of the mines where the explosions occurred the lamp was in use at a working face where the velocity of the ventilating current would be relatively low. The inference has been that the lamp was correctly assembled but that the gauze became sufficiently overheated to ignite the surrounding atmosphere.As part of its routine investigation of flame safety lamps the Bureau of Mines subjects each lamp to a test in still and moving atmospheres to determine its safety. Heretofore, as long as the lam, successfully passed this and other tests no determinations as to the margin between success and failure were made; hence, in attempting to answer inquiries concerning the reported explosions it was found desirable to be able to give actual gauze temperatures as a measure of the comparative safety of lamps under various conditions. The previous laboratory tests of flame lamps in still mixtures were made in a chamber or ""gallery"" of relatively small volume where the lamps might have been subject more or less to the smothering effect of the combustion products. It was therefore decided to make a special series of tests to obtain the gauze temperatures of both bonneted and unbonneted lamps in still and low velocity mixtures, using a larger gallery to offset any smothering effect.These tests are believed to represent the first attempt at measuring gauze temperatures by means of themocouples. The results will not only be of interest but will also be helpful to many in determining the status of flame safety lamps relative to gas ignitions in mines."

Feb 1, 1929

By Ludwig Schmidt

The petroleum industry has recently shown sucks great interest in the evaporation of crude oil and of gasoline, and in the prevention of evaporation losses that almost daily there is being developed and placed on the market equipment designed especially to reduce these losses. Among the recent developments is a new type of tank roof known as the "floating roof," which practically eliminates the vapor space over the surface of the oil, thus removing one of the chief causes of evaporation. There are at the present writing at least two types of floating roofs which, while similar in fundamental principle, differ mainly in the method of making contact with the inside shell of the tank. One type of floating roof is known as a floating tank deck, and has on its circumference flexible metal baskets containing gravel that .rest against the inside shell of the tank. In the other type of floating roof contact with the tank shell is made by the use of movable buffers or shoes. These are attached to the outer ring of the roof and are pressed against the tank shell by means of springs.

Jan 1, 1923

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By Frederick C. Trutt

Research performed on arcing faults and their interaction; with electrical insulating materials within coal.-mine power-system enclosures is described. This work was performed at The Pennsylvania State University from 1 December, 1976 through 30. November, 1977. Results presented are interim in nature and future research is planned to integrate the simulations which have been constructed, as well as to apply developed experimental procedures to the evaluation of electrical insulating materials for use in coal-mine enclosures. The thrust of this research has been divided into several primary areas. These include the development of a theoretical procedure for computation of three-phase and line-to-line arcing fault currents as a function of time, formulation of an arc model based upon thermal-arc plasma properties so that arc voltages and energies may be computed, development of a simulation for pressure and temperature rises when an arc interacts with an electrical insulating material within an enclosure, experimental evaluation of electrical insulating materials in terms of their tendency to support an arc as well as their potential contribution to enclosure pressure rises, and integration of the above research areas to form overall procedures for theoretical and experimental evaluation.

Jan 1, 1977

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924