Search Documents

By Foster Fraas

This report describes the application of pulsed magnetic fields derived from alternating and intermittent magnetizing currents. Application of such pulsed magnetic fields to the matrix-type separator permits (1) the complete discharge of the magnetic fraction with wet feeds and (2) the dry separation at particle sizes down to 325 mesh. At smaller particle s indications are that frequencies above 60 hertz will be required. Applications of intermittent magnetizing current to the cross-belt separator give the cross-belt-separator an advantage over the conventional constant-field cross-belt and induced roll separators; the intermittent current enables the cross-belt separator to separate matted fibrous and magnetically coagulating feeds, a type of feed that occasionally occurs with mineral, industrial, and secondary materials.

Jan 1, 1973

By Eugene T. Sheridan

The United States has extensive reserves of peat. Peat and muck lands are estimated at approximately 79 million acres, with reserves of 13.8 billion net tons. Within the past decade domestic production of peat has increased 2-1/2 times, and apparent consumption has tripled. During the same period imports have increased greatly, and in 1955 they almost equaled domestic production. The substantial increase in the demand for peat in the United States was due chiefly to expanding markets in agriculture and horticulture, for the reason that in this country peat is used primarily as a source of organic matter to improve the physical condition of mineral soils and as a mulch for shrubbery. A valuable constituent of any soil is its organic matter, and its depletion will injure cultivated soils and subject them to greater erosion.

Jan 1, 1957

In 2007, a total of 7,199 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.4% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Aug 1, 2009

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By L. J. Kane

Applications are described of various methods for determining the weight concentration and physical properties of solid and liquid impurities of gases in connection with problems encountered in synthesis-gas production. Of special interest among these methods may be listed: 1. A method developed for determining, the weight concentration of solid and liquid impurities in. hot, crude synthesis gas containing a high concentration of moisture. 2. A method developed for the same purpose but for highly purified synthesis gas or atmospheric air. 3. A method for obtaining a uniform dispersion of dry duet or, a microscope slide for particle-size determination or other purposes.

Jan 1, 1954

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

By William W. Aljoe

The hydrologic characteristics of two abandoned underground coal mine sites, near Latrobe, PA, and Uniontown, PA, were investigated by the U.S. Bureau of Mines for possible implementation of alkaline injection into the mine pools as a means of abating their acid discharges. The Latrobe site was chosen for a one-time application of alkaline injection to achieve a partial, short-term neutralization of a limited portion of the mine pool. A quantity of alkaline reagent (sodium hydroxide) sufficient for a one-time neutralization of the water in this portion of the pool was added. Although nearly all of the neutralizing reagent had moved away from the injection wells within 6 weeks, no evidence of neutralization was noted at the mine discharge during the study period. This lack of neutralization probably occurred because the injection wells did not intercept a primary flow path through the mine. Criteria for successful application of alkaline injection at this or other sites include (1) positive identification of the primary flow paths through the mine pool and (2) addition of quantities of alkaline reagent sufficient to neutralize the entire volume of the pool along the primary flow path.

Jan 1, 2010

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By Stephen C. Tadolini

The Bureau of Mines conducted field investigations in two underground mines to determine the actual loads to which bearing plates were subjected when installed in conjunction with full-column resin-grouted bolts and the roof movements generated by the applied loads. Measured loads indicate that the bearing plate is an integral part of the support system. Vertical displacement gauges installed to monitor roof displacements in the test sites show that the highest degrees of loading occur in conjunction with the largest amounts of movement.

Jan 1, 1986

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By Will H. Coghill, C. O. Anderson

In July 1921 , we were assigned by the U. S. Bureau of Mines to an investigation of milling methods in the Tri - State zinc district ( Missouri -Kaneas- Oklahoma district ) . The work has progressed without interruption , and about onehalf of the funds allotted for it has been expended . This preliminary statement abcut the nature of the work and the results so far obtained , has been prepared for the information of the operators , and through their assistance to insure the greatest possible progress during the remainder of the work . A general survey of the district was made , and many of the mining companies cordially offered the facilities of their plants for the investigation . The work was finally centralized at the plant of the 0. M. Bilharz Mining Co. Its manager , F. H. Gartung, and his successor , O. W. Bilharz , have been especially helpful , also the millmen at this plant and elsewhere have rendered assistance without which the work could not have advanced . The Missouri School of Mines and Metallurgy , Rolla, Mo. , and the Miami School of Mines , Miami , Okla . , have given hearty cooperation . The Webb City Iron Works and the Joplin Supply Co. donated some necessary apparatus .

Jan 1, 1922

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By H. B. Humphrey, F. E. Cash

The following information on accidents in Alabama during 1930 was compiled from data obtained from the companies represented in a course on accident prevention given by the United States Bureau of Mines in Birmingham. These mines produced nearly three-quarters of the tonnage of that State for the year, and included most of the larger operations in the district. The figures are probably representative of the mines which are doing recognized safety work, and are better than the average for all the mines in Alabama. Table 1 lists the days lost in accordance with the weights given to fatalities and permanent disabilities, part and total, which is the scale used in the National Safety Com¬ petition for Mines, conducted by this bureau. By way of explanation, temporary disabilities are weighted according to actual number of calendar days of disability, including Sundays and holidays — that is, all days are counted except the day of accident and day of employee's ability to return to duty. Hernia is classed as a temporary disability to be charged with the actual number of calendar days during which the employee was unable to work. Table 2 gives the number of accidents and the days lost from each cause at 45 coal mines and 7 iron ore mines, also the average frequency and severity rates.

Aug 1, 1931

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By F. C. Gibson

An electrical method for the continuous determination of propagation velocities in opaque, confined explosives, and propellants is described. A resistance element imbedded in the reactive material generates electrical signals that are displayed oscillographically and indicate the position and progress of a reactive zone associated with progress of a reactive zone associated with burning or detonation. The method is applicable to both solids and liquids.

Jan 1, 1963

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926