Search Documents

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

This report describes the development, installation and performance of a lonpwall illumination system. The longwall illumination system was installed at the Greenwich Collieries 112, Cockport, Pa. It utilized flourescent luminaires, intrinsically safe power distribution and is the first longwall system installed in Pennsylvania.

Jan 1, 1976

By Leonard Obert

Between 1927 and 1957, sodium borate minerals were mined by underground methods in the Kramer District, Kern County, Calif. In 1957, surface mining methods were initiated, and during the next two or more decades it is probable that most of the production from the district will be obtained from open pits. However, part of this borate deposit is sufficiently deep that surface mining may not be economical and, hence, at some future date underground methods may again be employed. This report was prepared to document the underground mining methods employed in the district before 1957. The general geology of the district and the detailed geology of each of four mine sites are presented, together with a mineral and mechanical description of the ore and enveloping rock. The report also describes the stoping, extraction, pillar support, methods of artificial support, and other factors that affect the structural characteristics of these mines.

Jan 1, 1962

By John C. Edwards

Standard smoldering and flaming combustion tests using smaIl coal samples have been developed by the U.S. Bureau of Mines as a method to evaluate the response of a smoke detector. The tests are con-ducted using a standard smoke box designed and constructed according to Underwriters Laboratories. The tests provide a standard, easily reproducible smoke characteristic for smoldering and flaming coal combustion, based upon a comparison of the smoke optical density and the response of a standard ionization chamber to the smoke. With these standard tests, the range of threshold limits for the response of a smoke detector and the detector's reliability can be evaluated for nearly identical smoke visibility and smoke physical characteristics. The detector's threshold response limits and reliability need to be well defined prior to the instrument's use as part of a mine fire warning system for improved mine safety.

Jan 1, 2010

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By William L. Crentz

Floyd County, KY., contains sizable deposits of high volatile bituminous coal. Some of the coals have been blended with higher-rank coals and used in the manufacture of high-quality metallurgical coke. The Upper Elkhorn No. 3, Upper Elkhorn No. 2, and Upper Elkhorn No. 1 beds produce the bulk of the present output in the county and contain the main known reserves of coal. Little information is available concerning the quality and extent of the deposits underlying the Upper Elkhorn No. 1 bed, although small operations in the past have worked a bed that is reported to be; the Lower Elkhorn. Undoubtedly, these lower beds occur in Floyd County, but depth Will preclude their development into a major source of fuel as long as large deposits of more-accessible coal are available. More is known of the occurrence of the beds above the Upper Elkhorn No. 3 owing to sporadic mining ventures in the upper measures. Many of the coal samples from beds above the Upper Elkhown No. 3. were collected in mines that had been abandoned. Almost all of the present production of Floyd County coal is taken from the Upper Elkhorn beds, and it is unlikely that their dominant position as coal producers will be challenged in the near future. Table 1 shows the coal production of the county by beds, during 1950.

Jan 1, 1952

By Walter Wood, J. T. H. Cannarella, H. F. Yancey, R. E. Zane

More than 50,000,000 tons of bituminous coal and probably about the same quantity of anthracite are cleaned annually in the United States by wet methods. The water, fine coal, and impurities from the water used for washing ordinarily are recovered by moans of various forms of settling tanks. Settling and clarification may be hastened markedly, thereby greatly increasing the capacity of clarification equipment already installed, by the addition of substances to the washery water that cause the fine particles in suspension to agglomerate and thus settle more rapidly. This phenomenon, although well known and applied in other fields, has been used at only a few coal washeries in the United States. It is widely employed, however, as an aid in the recovery or disposal of fine coal or impurities, as a means of preventing, stream pollution, and to enable reuse of washery water at many plants in Europe. Pioneering work in the United States has been done principally by two companies -- the Pittsburgh Coal Co., in Pennsylvania, 6/ and the Pacific Coast Coal Co., in Washington.

Feb 1, 1940

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By R. F. Chaiken

The Bureau of Mines has conducted a study of mine fires in the Anthracite Region of Pennsylvania to determine the most effective approaches to fire control in this area. The problems involved in controlling an anthracite fire include the geological and mining conditions in this area, the propagation characteristics of anthracite, the fire control methods available, the hazards associated with these fires, and the mar-ginal effectiveness of past fire control projects. From this genecal background, fire control options were discussed as they apply in ISBO to the Centralia mine fire. Probable effectiveness, feasibility, and costs were assessedv The options evaluated include four excavation plans, flooding, hydraulic flushing, water curtain isolation, mining to construct an underground carrier, burnout control, and relocation of the community. The most advantageous from a technical viewpoint is an excavation method combining complete excavation of the fire zone within the borough with trenching to confine the remaining fire. It appears that for many anthracite fires, as for the Centralia mine fire, there are no available control measures that have a moderate cost, are proven effective, and produce minimal disruption on the surface.

Jan 1, 1983

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By M. Mentser

The exchange of oxygen between carbon dioxide and carbon monoxide that occurs reversibly on carbon surfaces was studied at temperatures of 750° to 850°C and a pressure of 1 atmosphere. Carbon-14 was used to detect and measure the exchange reaction. The extent of oxygen exchange was a linear function of com- position of the gas mixture, and this relationship was used to evaluate the forward and backward rate constants of the reaction. Equilibrium constants, directly determined for oxygen exchange in this study, agreed well with values in the literature that were derived only by indirect procedures. This result establishes the validity of oxygen exchange in the mechanism of carbon gasification by CO2. Rates of carbon gasification were less than an order of magnitude slower than rates of oxygen exchange. Activation energies for these two processes were 58 and 53 kcal/mole, respectively. The closeness in the activation energies argues against any change in the rate-controlling step over a wide temperature span at atmospheric pressure. The role of CO as a retardant on the CO2-C reaction, and the nature of the carbon-oxygen complex are also discussed in view of the data obtained.

Jan 1, 1973

By W. W. Adams

"The results of the fourth annual safety contest, 'mown as the National Safety Competition, contacted by the United States Bureau of Mines are herein announced. A bronze trophy, ‘Sentinels of Safety’, the gift of the Explosives Engineer magazine, has been awarded to the leading mine in each of the five groups into which the mines and quarries that participated in the contest were arranged. These five groups were: anthracite mines, bituminous coal mines, metal mines, nonmetallic-mineral mines, and carries and open-pit mines. The leading plant in each group was the mine whose employee lost the smallest number of days from accidents in proportion to the total number of man hours worked. Where two or more mines operated without a lost-time accident, the winner was adjudged to be the plant which operated the largest number of man hours during the year.The contest was based upon reports of accidents and exposure sent by the competing companies to the Bureau of Mines. Records of the five leading companies in each group were made known to a Committee of Award, consisting of the following seven members: H. Poster Bain, Secretary of the American Institute of Mining and Metallurgical Engineers; James F. Callbreath, Secretary of the American Mining Congress; W. H. Cameron, Managing Director of the National Safety Council; H. L. Gandy, Secretary of the National Coal Association; A. T. Goldbeck, Director of the Engineering Bureau of the National Crushed Stone Association; William Green, President of the American Federation of Labor; and A. J. R. Curtis, Assistant to the General Manager of the Portland Cement Association. Members of the committee voted for the winning company in each group in accordance with the rules governing the contest.. A majority vote prevailed."

May 1, 1929

By Walter W. Kaufman

This Bureau of Mines manual for design of surface mine haulage roads covers such aspects of haulage road design as road alinement (both vertical and horizontal), construction materials, cross slope, and drainage provisions. Traffic control and design of proper lane widths to promote safe vehicle movement are included, as are suggested criteria for road and vehicle maintenance and for runaway-vehicle safety provisions. The aim of this publication is to provide those involved with surface mine haulage road design with a complete manual of recommended practices that, if implemented, will promote safer, more efficient haulage routes.

Jan 1, 1977

By D. C. Crowell, A. G. Loomis

Both Dimensional and Inspectional Analysis are developed from fundamental concepts , and dimensionless groups are derived which represent the viscous , capillary , and gravitational forces existing in two - phase , incompressible flow in petroleum reservoirs . It is shown how properly scaled models may be devised by means of the foregoing groups . Laboratory measurements with such models faithfully duplicate the behavior of the reservoir on a miniature dimensional and compressed time scale , and when all the pertinent variables are evaluated , the model is a most effective tool for the study of complex fluid displacements in the reservoir . Applying the Principle of Similitude , it is shown how dimensionally scaled models are applied to various types of reservoir displacements : ( 1 ) Oil displaced by water , ( 2 ) gas displaced by water , and ( 3 ) miscible displacement . The special case of water displacing gas by imbibition is analyzed , and it is shown that the dimensionally scaled model must be fabricated of sandstone rather than unconsolidated sand , which is generally used in such models . This report is intended to be a review and summary of the application of Dimensional Analysis to reservoir displacement problems for those who are beginning the study of this useful and interesting method .

Jan 1, 1964

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By H. C. Carpenter

This literature study of methods for desulfurizing residual fuel oil was conducted by the Bureau of Mines at the request of the Department of Health, Education, and Welfare. The sulfur compounds in residual fuels are believed to consist chiefly of condensed thiophenes and other polycyclic sulfur compounds. Hydrodesulfurization appears to be the most promising method for desulfurizing these oils and is the only method applicable to all types of sulfur compounds. There are indications in the literature that hydrodesulfurization without hydrocracking of residual oils may require higher pressures than used in present desulfurization processes, but no cost data and little experimental data are available on the higher pressure operation. Literature proposals for hydrogenating residual oils and heavy crude oils are exclusively for hydrocracking the oils to lower boiling products with accompanying partial desulfurization of the residual fuel fraction. Costs of the hydrocracking operations appear the closest available to probable costs of hydrodesulfurizing the oils, and have been reported (in 1955 to 1957) as $500 to $840 investment cost per daily barrel of capacity, with total operating costs of 70 cents to $1.10 per barrel.

Jan 1, 1963

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986