Search Documents

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By Frank S. Wartman

[ ]

Jan 1, 1927

By J. R. Boyle

The Bureau of Mines developed cost estimates fur the disposal of phosphate rock washer slimes by pond settling, from a study of the method used at the International Minerals a Chemical Corp., Moralyn Phosphate Operations, Polk County, Fla. Data were obtained by basing phosphate production and slime generation statistics on plant capacity rather than on actual company records. Cost estimates, which were prepared as a guide in evaluating alternative disposal methods and in identifying needed areas of research, could be applicable to any Florida plant using the same disposal method. To conserve mineral resources and to improve environmental conditions, the Bureau recommends further research directed toward developing alternative methods of disposal, including the recovery of water and P205 values from the slimes.

Jan 1, 1969

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in more intensified efforts in inspections of coal refuse sites. Inspections, however, are mainly qualitative and time consuming. In August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photointerpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Bibliographies of literature reviews in the area of past coal refuse embankment failures, monitoring instruments and methods, and photogrammetry are included.

Jan 1, 1977

By O. M. Schaus

This paper is one of a series, prepared by the Bureau of Mines and deals with the Montreal mine, one of only two active properties in Wisconsin on the Penokee-Gogebic range. The purpose of this paper is to describe the conditions of occurrence of iron ore in a particular property and to present sufficient details of equipment and production methods to convey to the unacquainted operator a correct idea of the mining practice.

Jan 1, 1930

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

Recent Bureau of Mines research in earth grounding safety is documented in three separate papers. First, guidelines for the design of a 5- ohm borehole ground are presented. Next, an inexpensive practical means to construct a low-resistance bed in high-resistivity soil is described. Finally, a procedure that employs a commercial resistivity meter to measure shock potentials around grounded objects is explained step-by-step. These papers complement the material presented at an earlier technology transfer seminar and published as IC 8767.

Jan 1, 1985

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By A. Soderberg

This paper describing the mining practice at the Utah Copper Co., Bingham Canyon, Utah, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Utah Copper Co. operates the low-grade open-out copper mine at Bingham Canyon, Utah, which is 30 miles in a southwesterly direction from Salt Lake City. In addition to the mine the company operates two flotation concentrators, the Magma plant and the Arthur plant, which have a combined capacity at maximum metallurgical efficiency of 60,000 tons daily. The concentrators are at Magna, about 18 miles from the mine. The company operates its own standard-gage railway, known as the Bingham and Garfield Railway, between the mine and the mills (fig. 1). Concentrates are smelted at the Garfield smelter of the American Smelting and Refining Co., situated 4 miles from the mills.

Jan 1, 1930

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By Ginger S. Evans

This report documents a preliminary hydrologic investigation of an area where longwall mining methods are to be used. The scope of work includes: determination of physical and chemical characteristics of major soil types in the area; determination of physical and chemical properties of surface water bodies; collection of geologic characteristics, including stratigraphy, structure, and detailed aquifer descriptions; collection of 10 years' meteorological data and installation of a weather station; and a detailed ground-water investigation that includes completion of observation wells, aquifer testing, water quality sampling, and analysis using a 3-D computer model. The Trescott model developed by USGS was used to simulate steady-state aquifer conditions. Input data from 8 multiple-completion monitor wells were used to model an area of approximately 10 square miles. Two layers, coal and overburden, were simulated, both confined. Model results showed good agreement with know piezometric data, desaturated areas, and flow from springs. The study area was found to have very low-yield bedrock aquifers with transmissivities ranging from 5 to 320 ft2/day for the coal (depths from 500 to 1,200 ft) and from 499 to 576 ft2/day and fractured sandstone units (depths less than 100 ft). Annual precipitation and recharge are very low, 10 to 11 inches and 0.25 inch respectively. The area has very high relief and large areas of rock outcrop. No perennial streams are present on the site.

Jan 1, 1983

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"""Rock-dust barriers""5 as they are termed in this country, are for the purpose of confining a coal-dust mine explosion to the limited area in which it originates. These barriers were first tested in 1910-1911, with favorable results under the conditions of test, at the French official gallery which was then at Lieven, Department of Pas-de-Calais. Shortly afterwards the Bureau of Mines in the course of its investigation of all practical explosion-prevention methods tried barriers in the Experimental Mine near Bruceton, using the primary form of simple fixed cross shelves 20 inches wide extending over the passageway and laden with rock-dust. The Bureau termed them “Taffanel barriers"" in honor of the director of the Lieven testing station. The trials were made in conjunction with tests of explosibility of different coal-dusts.Experience showed that although the principle of barriers had merit when they were used for secondary defence, the primary form was uncertain in effectiveness. This led the senior author to design mechanically discharging barriers to be operated by the compression air waves which precede the flame of an explosion. For the better understanding of the principal involved, it is pointed out that the advance air waves are what make a coal-dust explosion possible by stirring up the coal-dust from the walls and floor of the passageway. If a barrier can throw inert dust into the air to form a cloud as dense or denser than that formed by the coal-dust, it will neutralize the explosiveness of the coal-dust, and the flame of the explosion will be extinguished. When the flame ceases, the pressure dies away in a short distance if the 'area that had been traversed by the explosion is not large."

Jan 1, 1930

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By H. F. Feldmann

This Bureau of Mines report presents a method for the computer solution of the equilibrium compositions of any complex, multiphase, chemical system for which appropriate thermodynamic data are available. The method describes in detail the computation of systems in which solid or liquid species can form by heterogeneous chemical reactions where these species do not occur in any equilibrium equations. Also described are the calculation of phases formed by condensation (pure or solutions) and the inclusion of other system restrictions such as electroneutrality. The method is being used to compute the equilibrium composition of mixtures of an electrically conductive plasma and a liquid slag phase arising from the high-temperature combustion of coal for magnetohydrodynamic power generation. These mixtures can contain up to 65 species including gases, liquids, free electrons, and ions.

Jan 1, 1969

By T. W. Quayle

This paper describing mining practices at the United Verde copper mine, Jerome, Ariz., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts f the United States. At present mining operations are being conducted both underground and by electric shovels in an open pit. The open-pit work has been described by E. M. J. Alenius in a previous publication of the Bureau of Minos;3 the present paper will be confined to a description of the underground mine. The underground methods comprise horizontal cut-and-fill, shrinkage with delayed filling, horizontal square-set, inclined square-set, and top slice. The normal daily production of the underground mine is 3,000 tons of copper ore per day, requiring the employment of 900 men underground.

Jan 1, 1931

By Claude W. Sill

In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of. Tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate; It seemed likely that the, same general procedure could be used in determining semimicro quantities of uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant its turn permits the use of the very stable indicator, ferroin, with its sharp color.., change and exactly reproducible blanks. Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Gleu. The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months.

Jan 1, 1952

By R. C. Annear

This report describes open, sublevel, and shrinkage stoping at the Greenwood mine, operated by Inland Steel-Co. The iron ore mine is in Marquette County, Mich., about 6 miles southwest of Ishpeming (fig. 1). The Greenwood is one of three active underground hard-ore mines on the Marquette range, the others being the Cliffs-Shaft and the Champion mines. The operation reflects an achievement in exploiting small, difficult-to-mine hard-ore bodies lying beneath a 200-foot overburden of glacial drift, which is partly water bearing. This report can indicate only briefly the efforts of personnel in overcoming adverse conditions in mining more than 2 million tons of ore, 80 percent of which was in lump form, for open-hearth production of steel. Significant data presented include descriptions of the principal mining methods employed, sublevel and shrinkage stoping; percent aged mining costs for the entire year 1957, covering both direct mining costs and general expenses; and performance records in units of labor, power, and supplies.

Jan 1, 1960

By Robert L. Lagace

A prototype adaptive volume control for the loudspeaker output of mine trolley carrier phones was designed, built, and tested in the laboratory and in a mine. This volume control senses, and adapts to, the ambient acoustic noise environment in such a way as to produce a loud sound output under noisy conditions, and a quieter output under quiet conditions, thereby producing an understandable and unstartling volume level under all noise conditions. The design approach, prototype hardware, and test results are described, and the device is shown to be feasible for in-mine operations. The circuit design principles are easily applicable to currently available mina trolley carrier phones. Recommendations for practical improvements are included. An in-mine experiment to assess the practical feasibility and utility of the dedicated wire technique for overcoming poor trolley carrier phone system performance was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated auxiliary wire, placed in the rail haulageway, which allows signals to naturally couple to and from the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated wire experiment, results, and conclusions are described, and the technique is shown to be a valid and practical one for significantly Improving carrier phone system performance in mines. Guidelines for the installation and use of the dedicated wire are provided. Recommendations are made for obtaining further practical information on its performance and utility. A second in-mine experiment to assess the feasibility and utility of the low-impedance (low-Z) line technique for overcoming poor carrier phone signal transmission in mines was designed, performed and evaluated. The low-Z line technique involves the periodic connection of shunt capacitors between the trolley wire and the rail to artificially lower the line characteristic impedance. This causes the low impedance shunt loads encountered across the trolley wire/rail line to be less mismatched to the line, thereby reducing the overall attenuation of carrier phone signals. The results of in-mine experiments performed along unenergized and fully operational sections of trolley wire/rail line are described. The experiments were designed to measure line parameter such as inductance and capacitance per unit length, characteristic impedance, and propagation phase velocity, in addition to signal strength versus distance behavior under normal and low-Z line conditions. The low-Z line technique is shown to be valid, but not as practical as the dedicated wire technique which is recommended as the most favorable for most coal mine applications.

Jan 1, 1979