Search Documents

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

By George A. Bell

This paper reviewing the leaching practice of the New Cornelia mines of the Calumet & Arizona Mining Co. at Ajo, Ariz., is the first of a series being prepared by the Bureau of Mines on leaching methods and costs in the various mining districts. ACKNOWLEDGMENTS The author acknowledges the assistance of T. G. Chapman, consulting engineer, and E. D. Gardner, supervising engineer of the Southwest Experiment Station, Bureau of Mines, Tucson, Ariz.

Jan 1, 1930

By Brian T. Brady

The year 1991 recorded unprecedented change throughout the world; war in the Middle East, economic recession in key industrial nations, upheaval in Eastern Europe, and the disintegration of the former U.S.S.R. These issues and growing environmental concerns will affect the entire world mining industry. Environmental issues continue to have an ever greater effect on industrial minerals. In the United States, major issues involving the Clean Air Act, Clean Water Act, and the recent Stormwater Rule by the U.S. Environmental Protection Agency (EPA) affect many types of mineral operations. Significant developments include an important decision in 1991 by a Federal Appellate Court to overturn EPA's asbestos ban on certain products, partly on environmental grounds, and proposed legislation that would overhaul or abandon the 1872 Mining Act. On a global scale, prominent issues include environmental concerns over mining in the Antarctic and Arctic regions and a cutback in plans to clean up the Kola Peninsula in the Commonwealth of Independent States (C.I.S.).

Jan 1, 1993

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By Oliver C. Ralston, Dorsey A. Lyon

The data reported in this bulletin are largely the result of experiments conducted by the Salt Lake City station of the Bureau of Mines in cooperation with the department of metallurgical research of the University of Utah. The work on lead is only one of the phases of the investigations carried on at that station during the years 1914 to 1916. The results of similar work with zinc ores and with copper and other ores will be published in future reports of the bureau.

Jan 1, 1918

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By O. H. Metzger

This is one of a series of papers being published by the Bureau of Mines on mining areas and districts in the Western states. It describes mining and milling practices in the vicinity of Wickenburg in Maricopa and Yavapai Counties, Ariz. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of the operators of the mines visited. Reports of geologists and engineers who previously visited the area were drawn upon freely. Individual acknowledgments are made in the text.

Jan 1, 1938

By Forrest T. Moyer

THE injury data and experience in this bulletin are presented in three general sections. The first section contains general and detailed data relating to 1948 injury experience in bituminous-coal and Pennsylvania anthracite mines, separately and combined into totals for all coal mines. The related employment, worktime, production, and productivity data are given in each breakdown of the statistical data. Tables 1 through 22 constitute a subsection and present statistics on number of injuries, frequency and severity rates, average severity, detailed and major causes of injuries, injury records of the coal-producing States, distribution of injuries by part of body, and distribution of injuries by days of disability. Tables 23 through 45, the second subsection, present injury experience in bituminous-coal mines by various selected factors of physical or operating conditions that ma contribute to the occurrence of injuries. The degree of mechanical loading, productivity, size of mine by number of men working and by tonnage mined, thickness of bed, length of shift, number of shifts, type of cap lamps, rating of mine as gassy or nongassy, type of ventilation, and combinations of these factors influencing mine safety are presented in this group of tables. Similar data on Pennsylvania anthracite mines are listed in tables 46 through 63, which comprise the third subsection. The second section of the report contains the generalized annual injury records of bituminous-coal, Pennsylvania anthracite, and all coal mines from the earliest available data through 1948. Tables 64 through 97 list the number of fatal and nonfatal injuries, injury rates, and causes of injuries on an industry basis, the long-term injury records of each coal-producing State, and the related employment, worktime, and production data.

Jan 1, 1952

By Bruce K. Cantrell, Jon C. Volkwein

Exposure to mineral aerosol is an occupational health hazard in mining and mineral processing industries because of the risk of developing pneumoconiosis. Agricola (1556) described this hazard for metal mining in Carpathia. He described shortness of breath and consumption, conditions that are now associated with asthma and emphysema. By the end of the nineteenth century, several respiratory diseases were known to affect miners, including silicosis and coal workers' pneumoconiosis (Fletcher, 1948; Seaton et al., 1981). For example, silicosis, not tuberculosis, was clearly recognized as the hazard in the Vermont granite quarries and stone-cutting sheds (McFarland, 1927). The Gauly Bridge Tunnel disaster in the mid-1930s caused the deaths of an estimated 700 workers by acute silicosis and focused the nation's attention on this disease (Cherniack, 1986). By the mid-twentieth century, it was clear that risk of simple pneumoconiosis is associated with a miner's cumulative exposure to mine aerosol in the respirable size range and that prevention lies in reducing that exposure through regulation (Seaton, 1986). In the United States, regulation of mine worker exposure to airborne mine dust is the responsibility of the Mine Safety and Health Administration (MSHA) in the U.S. Department of Labor. The key legislation relating to improved mine worker health was the Federal Coal Mine Health and Safety Act, enacted in 1969 (U.S. Congress, 1969) and subsequently amended as the Federal Mine Safety and Health Act of 1977 (U.S. Congress, 1977). MSHA receives technical assistance from the National Institute for Occupational Safety and Health (NIOSH). NIOSH also provides recommended exposure limits (RELs) for contaminants to MSHA. MSHA's regulation of mines includes the establishment of a dust standard administratively based on the these RELs. Some mine operators must submit a dust control plan designed to meet the dust standard. Periodic mine inspections determine if mines are com- plying with both the dust standard and the dust control plans (MSHA, 1991). The most common dust measurements are those for respirable dust (according to the definition given in Fig. 26-7), that is, the fraction of aerosol particles able to reach the gas exchange region of the lungs. The other health-related size fractions (inhalable and thoracic-see Fig. 25-1, and "total" dust) are also occasionally measured. A "total" dust measurement is defined by the common practice of the last 30 years or so, using 25 mm or 37mm plastic cassettes (e.g., from PAL, MIL, SKC ). The types of mines have been categorized

By Ernest A. Curth

Statistics For 1956-66 show that mine transportation accidents accounted for 19 percent of fatalities in bituminous coal mines, second only to roof deficiencies as a cause of death. Productivity per man-shift increased from 10.2 tons in 1956 to 18.4 tons in 1966, but the fatalities per million man- hours of exposure also increased from 0.19 to 0.21 during that same period, indicating that transportation hazards still persist. Consequently, the Bureau of Mines reviewed the transportation fatalities that occurred in bituminous coal mines during 1956-66. The data were processed by computer to find what constitute hazardous conditions and unsafe actions as well as to correlate occupation and age of victims, transportation type, and mine production. Environmental factors and equipment defects which create hazards, as well as unsafe actions of personnel, were determined for each type of mine transportation: Track haulage, mobile nonrail haulage, conveyors, hoists, automotive operations, and front -end loaders, and for transfer stations (loading points, slope and shaft bottoms, surface transfers) and railroad yards. Man-trip accidents, a group with a catastrophe potential, also were analyzed. The basic design and operational features of each transportation type were outlined and procedures considered safe in the light of accident experience were suggested. Findings show that unsafe actions of personnel and hazards created by environmental deficiencies or equipment malfunctions contribute equally in causing transportation accidents. Accordingly efforts should be directed toward improving working conditions, equipment maintenance, and education and training of employees. The trend is toward using safer modes of transportation, notably conveyors. More attention should be given to track haulage operation, railroad yards, and nondestructive field testing of materials.

Jan 1, 1971

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

By Robert E. Wood

The compressibility factors, Z, of helium, nitrogen, and helium-nitrogen mixtures in the three-dimensional space of temperature, pressure, and gas composition have been related to the Leiden form of the virial equation of state. The dependency of virial coefficients through the fifth on temperature and gas composition has been established for the temperature range 133.15° to 748.15° K. Compressibility factors, Z, have been computed from the equation of state and tabulated as functions of gas composition, pressure, and temperature. Tabular values of Z are presented for 30.00 through 100.00 percent helium for temperatures from 240° through 700° R for pressures from 14.696 through 3,050 psia and for temperatures from 720° through 1,300° R for pressures from 14.696 through 1,500 psia. Tabular values of Z are presented at increments of 5.00 percent helium and 20° R, and, for pressures greater than 50 psia, at increments of 50 psi.

Jan 1, 1967

By C. Harry Benedict

This paper, describing the leaching practice at the Calumet and Hecla mills, Lake Linden, Mich., is one of a series on milling methods and costs being published by the United States Bureau of Mines. GENERAL DESCRIPTION The reclamation plant is located along the shores of Torch Lake at a slightly lower level than the concentrator itself. The entire location of the original concentrator, in connection with the present reclamation plant, has been ideal, lore particularly as the leaching and flotation departments are common to both units. After 15 years of operation and with the reclamation sands just a little more than half exhausted it would appear that the remaining life of the deposit could be worked by the present plan, without decided changes or renewals of plant or equipment.

Jan 1, 1930

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By M. K. Quinn, A. W. Khair

"This paper presents an analysis of respiraple dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photo¬graphed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.IntroductionThe continuous-mining machines introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal sine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumo-coniosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (Newmeyer, 1981). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood-block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 2010

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By G. D. Jermain

The Bureau of Mines investigated the Gypsum-Camel deposit on Iyoukeen Cove Chichagof Island, Southeastern Alaska, from April 21 to August 26, 1948, as A part of the United States Department of the Interior program for developing an Alaskan construction industry. As gypsum is one of the components necessary for the manufacture of cement and one of the raw materials for plaster and plaster-board products, it is desirable to locate and develop a readily accessible deposit of gypsum in Alaska. In 1928, B. D. Stewart of the Territorial Department of Mines surveyed the gypsum deposits at Iyoukeen Cove, and during the summer of 1946 George M. Flint, Jr., and Edward H. Cobb of the Federal Geological Survey examined and mapped the old workings at Gypsum Creek and the prospect at Iyoukeen Cove. Both the Territorial Department of Mines and the Federal Geological Survey recommended the Gypsum-Camel prospect as warranting a diamond-drilling program by the Bureau of Mines. The Bureau of Mines project consisted of cleaning out and sampling, the old underground workings and diamond drilling from the surface to ascertain the lateral extensions of the deposit.

Jan 1, 1952