Search Documents

By C. W. Van Noy

The procedure suggested in this report is intended for the use of engineers, esters, accountants, etc., in estimating the cost of chemical-type operations. It is intended to over operating costs, not investment costs, as the latter have been covered numerous other publications. However, as capital investment costs are reflected to a high degree in operating costs, it is important to point out that accuracy of investment costs is highly essential. Therefore, all factors that might be included under plant -capital costs should be considered, such as requirements of shops, employees' housing, etc. The procedure is designed primarily for use in types of chemical oper¬ations, such as the production of synthetic liquid fuels, anhydrous ammonia, and others of like or similar nature. Yet, no attempt has been made to cover the entire chemical industry.

Jan 1, 1949

By Will H. Coghill, I. L. Feld, G. D. Coe

The object of this paper . is to make known the superior classification accomplished in a hydraulic classifier designed to make use of principles determined by recent research ... The details of the design , the results of preliminary research , and the final testing are given . The classifier of the new design shown in figure 1 and another one like it are in operation as concentration classifiers in a Birmingham iron- ore mill recovering 4 tons per hour of concentrates from table middling that ` otherwise would require regrinding and retabling . The four factors that contribute to the successful operation of these classifiers are ( 1 ) a teeter column of small diameter , ( 2 ) use of an open - bottom tooter column classifier with a periodic pincer instead of the usual type , which terminates in a vortex, ( 3 ) a sorting chamber under separate hydraulic control , and ( 4 ) a teeter column of more than the usual depth . · At the outset it must be stated positively what the authors mean by hydraulic classification : They mean the reconstruction of a multimineral ground product into fractions graded with respect to size , so that cach fraction has the heavy mineral segregated in the fine sizes and the light mineral segregated in the coarse sizes . This definition presupposes that in multiplespigot classification the low specific gravity minerals are carried beyond the first cells to the later ones . The reader must take into account that , from the standpoint of classification , " ores " may be divided into two types , represented - by the following : ( 1 ) Joplin flint - blende ores , which , because of the hardness of the flint and the softness of the blonde , yield upon comminution a product that already has the essence of classification ; and ( 2 ) Birmingham Big Seam iron oros , which contain " easily shelled - out " sca sand and , upon reduction to about 10 mesh , yield a heterogeneous mixture in which the size analyses of the respective " floats " and " sinks " arc almost identical .

Dec 1, 1945

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth transmission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.

Jan 1, 1980

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By George H. Holmes

This paper is one of a series on mining methods and practices published by the Bureau of Mines. It describes quarrying methods and crushing practices of the U. S. Lime. Products Corp. at its Sloan and Apex quarries. Calcining and milling processes. at the Sloan and Henderson plants also are outlined. The Sloan dolomite and limestone quarries and plant are in secs. 12 and 13, T. 23 5., R. 60 E., and sec. 18, T. 23 S., R. 61 E., M.D.B. &M., Clark County, Nev., about. 17 miles by paved highway southwest of Las Vegas (fig. 1). The Apox limestone quarry, and crushing plant are in sec. 26, T. 18 S., R. 63 E., M.D.B.&M., Clark County, Nov., approximately 18 milos northeast of Las Vegas, adjacent to U. S. Highway 91 (fig. 1). The Henderson calcining plant is Inc., in sec. 13, T. 22 S., R. 62 E., 14 miles southeast of Las Vegas on U. in a reduction unit of Basic Magnesium, M.D.B. &M., Clark County, Nev., about S. Highway 93 (fig. 1).

Sep 1, 1949

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba fields were studied]

Jan 1, 1941

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By T. T. Campbell

This report traces the development of techniques for the preparation of high-purity rare-earth metals. Rare-earth metals, excepting samarium, europium, and ytterbium, were prepared by converting their oxides to anhydrous chlorides or fluorides and reducing the rare-earth halides with active metals such as lithium or calcium. High-purity, anhydrous rare-earth chlorides were prepared by dissolving the rare-earth oxides in hydrochloric acid to form hydrated chlorides and by subsequently dehydrating the hydrated salts in the presence of ammonium chloride at temperatures ranging from 70° to 360° C. while under reduced pressure (50 microns to 1 inch Hg). The chlorides were also prepared by direct chlorination of rare-earth oxide-carbon mixtures. Reaction efficiencies in excess of 95 percent were obtained by either method; however, purer chlorides were prepared by the aqueous ammonium chloride conversion method. Purification of yttrium chloride by high-temperature vacuum distillation proved to be an effective method of separating, oxygen-bearing compounds from the chloride. Yttrium metal prepared from purified chloride contained significantly smaller amounts of oxygen (990 p.p.m. oxygen in yttrium metal prepared from raw chloride and 200 p.p.m. in that prepared from distilled chloride).

Jan 1, 1961

By S. M. Shelton, W. A. Calhoun

"INTRODUCTION Discovery and development of a southwestern Arkansas quicksilver district are recent history. In July 1930 4/, a specimen was discovered near the Little Missouri River in sec. 1, T. 7S. R. 26 W., which was identified as cinnabar. In the summer of 1931, Leo Yount began prospecting for cinnabar near the Little Missouri River. In the fall of that year he operated a small three-tube retort near the present Parker Hill mines and produced several flasks of quicksilver. Yount optioned a considerable block of ground containing the best showings in the Little Missouri River area, and on February 19, 1932, he and W. C. McBride, Inc., of St. Louis, Mo., formed the Southwestern Quicksilver Co., which was the largest producer in the district until operations ceased in September 1934.The Southwestern Quicksilver Co. installed a rotary furnace on Parker Hill in April 1932, which treated ore from the three principal mines Gap Ridge, Parker Hill, and Parnell Hill. In 1934 production was entirely from the Gap Ridge and Parker Hill mines. Nothing was done at Parnell Hill except a little small-scale work on a share basis.Mercury Producers, Inc., later took an option on the holdings of the Southwestern Quicksilver Co. and in June 1935 began operations. The company produced considerable quicksilver before the lease and option were surrendered in the summer of 1936. Most of the work of Mercury Producers, Inc., was on Parnell Hill, but some work was done on Parker Hill and at the Bell prospect on ground not controlled by the Southwestern Quicksilver Co."

Mar 1, 1942

By R. T. DeWoody, J. W. Chester, W. C. Miller

The work was done to develop a relatively efficient muffler for quieting the exhaust of a rock drill . The exhaust of a pneumatic rock drill is the source of the major part of the noise generated by the drill . The exhaust noise can be reduced in a number of different ways , but this study involved only reactive mufflers . The reactive muffler can be simulated by an electrical circuit . Information obtained from analogous electrical circuits was used to design an efficient exhaust muffler for pneumatic rock drills . Electrical analogies proved to be a valuable tool in the design of mufflers .

Jan 1, 1964

By S. H. Ash

Probably one of the most significant departures in tunneling practice is the introduction of Diesel locomotives far haulage (Diesel trucks have been used for some time). The fallacy of the belief that they do not generate carbon monoxide or toxic gases and can be used indiscriminately has been proved by the authors through observation for several years of atmospheric conditions surrounding the use of Diesel engines in tunnels. Diesel locomotives haves been introduced in tunnel haulage for reasons other than safety or health. Except to the extent that they replace trolleys, with their danger of causing electrocutions, modern Diesel locomotives do not increase safety Or remove any ordinary hazards to safety or health. In fact, they create such hazards, the extent of which is limited entirely by the carbon monoxide-content level set, method of ventilation, adequacy of the measures.

Jan 1, 1942

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

By Ludwig Schmidt

[Steel tanks often corrode rapidly in oil fields where the gas produced with crude petroleum contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion. Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide L; as in solution, and has exhibited no serious corrosive action. These uses indicated that aluminum tanks might be equally effective in counteracting hydrogen sulphide corrosion. Consequently, in the spring of 1928, an all-aluminum stock tank of 500 carrels capacity and a "composite" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co. in Crane County, Tex. These tanks were under observation for one year, the test being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Real Co. The results of this preliminary test sustained the belief that aluminum is highly resistant to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the large quantities of highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the Aluminum Co. that additional tests be made to include production conditions in which large quantities of brine would be handled, for pact experience had known that aluminum often is susceptible to the corrosive action of brines.]

Jan 1, 1931

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

By Ludwig Schmidt

Steel tanks often corrode rapidly in oil fields where the gas produced with crude petroleum contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion. Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no serious corrosive action. These uses indicated that aluminum tanks might be equally effective in counteracting hydrogen sulphide corrosion. Consequently, in the spring of 1928, an all-aluminum stock tank of 500 barrels capacity and a "composite" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co. in Crane County, Tex. These tanks were under observation for one year, the test being sponsored by the Gulf Production Co., the Aluminum Co. of America, rind the Parkersburg Ric and Real Co. The results of this preliminary test sustained the belief that aluminum is highly resistant to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the Wake were not subjected to contact with the large quantities of highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of .the Aluminum Co. that additional tests be made to include production conditions in which large quantities of brine would be handled, for past experience had shown that aluminum often is susceptible to the corrosive action of brines.

Jan 1, 1931

By E. A. Hewitt

This paper describing the mining practices at the Park Utah mine in the Park City district is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Park Utah mine is situated at Keetly, Utah, about 5 miles east of Park City. The Park City district lies on the eastern slope of the Wasatch Mountains, 25 miles southeast of Salt Lake City. The district embraces a tract located between the crest of the main range on the west and the mountain meadows along the eastern foothills. The elevation of the Union Pacific Railroad station at Park City is 7,000 feet above sea level. The town and mines are served by two railroads; one 28 miles long is a branch of the Union Pacific Railroad and connects with the main line at Echo Junction, east of Ogden; the other is 35 miles long and joins the Denver & Rio Grande Western Railroad at Salt Lake City. The district and mines are also accessible by excellent automobile roads from Salt Lake City and surrounding points (fig. 1).

Jan 1, 1930

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978