Search Documents

By Irvin G. Burough

Andros Analyzers Incorporated has designed and built two prototype continuous methane monitors capable of being mounted on a mining machine'. These instruments were designed for in-mine safety use. The monitors incorporated an NDIR optical/electronic analyzer design in which the response to the sample gas (methane in air) was achieved by synchronous detection and measurement of the amplitude oscillations of the trasmitted energy from an infrared source caused by the pressure modulation of the sample gas within the optical cell. Zero and span stability were to be achieved by the amplitude modulating of the infra-red source and using detected signal to correct for optical/electronic system variation. This design effort was to simplify and reduce the cost of the major components while eliminating the need for daily calibration. This report is the final report on this effort.

Jan 1, 1981

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By James M. Spear

The U.S. Bureau of Mines conducted a mineral survey of the Domeland Addition (5207) and Woodpecker (5206) RARE II areas during the summer of 1979. These study areas were examined to determine the presence or absence of mineral resources and reserves and where possible, to estimate values. The study areas are 9 air mi northeast of Kernville, California, and encompass 47,400 acres of primarily granitic rocks of the Sierra Nevada batholith with some scattered exposures of older metasedimentary, volcanic, and metavolcanic rocks. These other rock units partially surround the exposed batholith in the Domeland Wilderness and consist mostly of late Paleozoic quartzites, mica schists, marbles, and meta-volcanics, Mesozoic quartz diorite and gabbro intrusives, and local Tertiary basalt and andesite flows.

Jan 1, 1981

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By Charles Enzian, Donald F. MacDonald

It is a far cry from the small and uncertain mining efforts of 50 years ago to the splendidly equipped and solidly financed organiza- tions that now handle thousands of tons of ore per day. The old mining was largely speculative; the new is practically on a manu- facturing basis. In the old days of mining the aim was, chiefly, to find comparatively rich ore; modern practice looks more toward efficiency in mining and milling, so that vast tonnages of low-grade material may be worked at a profit. The old operators had faith and hoped for good returns; the new ascertain with a fair degree of precision what the available tonnage is, what the cost of mining and treating the ore will be, the time necessary to exhaust the deposit, the capital required, and the net profits to be made. The old mining was financed on a highly speculative basis, and the value of mining stock was largely controlled by the imaginations of the promoters and of the individual holders. In the new régime the financing of mines is often as conservative as the financing of manufactures or railroads, and the value of stock, quoted on the leading exchanges, is controlled by the carefully estimated profits in sight. Of course, with every legitimate industrial enterprise go certain business risks, and mining is not exempted from these. Then, too, valueless mining as well as valueless industrial stocks are sometimes offered for sale by the intentionally dishonest, or the ignorant. However, the prospective purchaser of a mine nowadays, if he is willing to pay for the services of reputable mining engineers, can obtain information on which to base an opinion as to the quality of his investment. The relatively recent development of cheap and efficient methods of mining and of ore dressing has given value to low-grade ore bodies that a few years ago were almost valueless. The iron mines of northern Minnesota have been fruitful in developing efficiency in mining methods, notably the open-cut methods in which steam shovels strip off the overburden and then load the ore directly into railroad trains for transport to the furnace. In 1907 open-cut mining was applied to the low-grade copper ores of Bingham, Utah, with splendid results, and since then it has won a most important place in the min- ing of large masses of low-grade ores in several other mining regions, especially at Santa Rita, N. Mex.

Jan 1, 1916

By Maria I. De Rosa

Analysis of mining equipment fires from 1990 through 1999 reveals that there were 340 large mining equipment fires, resulting in 72 injuries and five fatalities. Many of the fires resulted in the loss of equipment and all posed potential or real risks to the operator. In 97 cases, the fires raged out of control due to engine shut­off failure, even upon activation of the machine fire suppression system, due to the spraying of pressurized hydraulic flu­id and fuel onto hot engine surfaces. In other cases, even after engine shutoff, the fires re-ignited, fueled by the contin­ued flow of flammable fluids remaining in the lines onto the hot engine surfaces. In many of the fires, flammable vapors evolved and penetrated the cab, violently igniting, forcing the operator to exit under very hazardous conditions. The use of emergency evacuation lines in the fuel and hydraulic fluid systems, and methods to reduce or prevent the spraying of pressurized fluids onto hot engine surfaces would greatly improve the chances of successfully suppressing large mining equipment fires. In addition, the use of systems for preventing the ignition of flammable vapors inside the cab, and detecting and suppressing fires originat­ing in the cab, would greatly enhance operator safety. The National Institute for Occupation Safety and Health (NIOSH) recently conducted experiments on meth­ods to reduce the fire hazards associated with large mining equipment. These experiments evaluated the use of cab inerting systems to prevent the ignition of flammable vapors inside the cab and sup­press fires originating in the cab, while maintaining a breathable atmosphere for the operator to bring the equipment to a stop and safely exit the cab.

Jan 1, 2008

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system&apos;s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system&apos;s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

By D. E. Pollock, T. W. Beck, J. A. Organiscak

This work presents the findings from a number of NIOSH studies evaluating the impacts of emerging technologies that may reduce dust exposures for continuous mining and roof bolting personnel. These technologies include use of a wet head cutting drum on a continuous mining machine that places water sprays on the cutting drum instead of placing them on a manifold outby the drum. Evaluations at two separate operations showed that the use of the wet head sprays reduced dust levels at the miner operator in the return air, although these reductions were quite variable. NIOSH also assessed the effectiveness of a canopy air curtain for protecting roof bolting personnel. The data showed that dust levels were lower beneath the air curtain than outside the air curtain. This study also suggested several future modifications to the air curtain to in-crease its effectiveness. Finally, NIOSH evaluated mist drilling technology for its effectiveness in controlling respirable dust exposures of bolting personnel. A recent study showed that higher dust levels existed around a machine using the mist system compared to a machine using a conventional vacuum system for dust control. Unfortunately, the true impact of mist drilling was confounded by this machine operating downwind of the continuous miner for much of the study.

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.