Search Documents

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscilloglaph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By J. W. Paul

The United States Bureau of Mines has made a study of roof control in 68 mines operating in the Pittsburgh coal bed in Pennsylvania, West Virginia, and Ohio. In making these studies, much information was also obtained on various exact methods of development and pillar extraction as practiced by this large group of mines. It is proposed in this paper to describe these methods, by which this group of mines in 1931, a year of reduced industrial activity, produced 28,123,000 tons of bituminous coal - 7.4 percent of the national production for the same year and an amount equal to the combined production of the coal mired in the States of Alabama, Colorado, New Mexico, Utah, and Wyoming. The results of these studies, insofar as they pertain to the prevention of injuries from falls of roof, have been published by the Bureau of Mines. In this paper only a few mines typical of each system will be described; however, should the reader be interested in other details with respect to these mines, he may refer to the following publications: T.P. 522, 1932, 43 pp. Falls of roof and coal in mines operating in the Pittsburgh coal bed in Marion and Monongalia Counties, W. Va., by J. W. Paul and J. N. Geyer.- A study of nine mines in these two counties of northern West Virginia.

Jan 1, 1935

By J. C. Duchon

The U.S. Bureau of Mines is conducting human factors research for the purpose of reducing accidents and improving the person-machine interface found in surface and underground mining operations. Miners are exposed to a variety of environmental stressors, e.g., extreme heat, noise, vibration, and adverse illumination, throughout the workday. Exposure to these environmental stressors has been noted in the literature to affect performance on vigilance tasks. Since impaired performance at vigilance tasks can lead to industrial accidents, further investigation of the effects of environmental stressors on human performance is warranted. A brief description of the environmental conditions present in the mining workplace is followed by a review of experiments dealing with the effects of environmental stressors on vigilance task performance. The applicability of past research to actual mining operations is considered.

Jan 1, 1989

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The National Institute for Occupational Safety and Health (NIOSH), through an informal partnership with industry, labor, and the Mine Safety and Health Administration, has developed and tested a new type of instrument known as the personal dust monitor (PDM). The dust monitor is an integral part of the cap lamp that a miner normally carries to work and provides continuous information about the amount of respirable coal mine dust in the breathing zone of that individual. Testing was conducted on 25 prototype instruments in the laboratory to verify the instruments’ accuracy as received from the manufacturer and after a period of underground use. The laboratory testing verified previous work; there is a 95% confidence that the individual PDM measurements were within ±25% of reference measurements. In-mine testing determined the precision, durability, and miner acceptance. Data from the mines showed a field precision of 0.078% relative standard deviation for the PDM and 0.052% for the recognized standard—the coal mine dust personal sampler unit. The PDM had about 90% availability for collecting valid information in over 8,000 hr of underground use. Anecdotal comments by miners indicated that they found the PDM more convenient to wear for sampling than currently used instruments because of the integration of the sampler into the normally worn cap lamp. The means of the instruments’ pre- and postmine accuracy verification test values were statistically equivalent. Additional data were collected to measure the equivalency of the PDM to the U.K. Mining Research Establishment sampler, as required by U.S. law. However, analysis of the data was more complex than originally anticipated because the variance with increasing concentration required use of a more sophisticated statistical model. Explanation of and results from this work will be the subject of a second publication. Under the broad range of test conditions covered in this work, the PDM functioned as well as the current sampler in terms of availability for use, accuracy, precision, and miner acceptance.

Jan 1, 2006

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By Gary A. Kingston

Rolled steel, steel forgings, and steel castings in the Pacific Northwest (Washington and Oregon) are produced principally in the Seattle, Wash., and Portland, Oreg., metropolitan areas. Steel-mill products are rolled from carbon and some alloy &eels by three companies into shapes such as reinforcing bar, rods, rounds, squares, flats, and hot-rolled strips; structural shapes, - such as angles, channels, and I-beams, also are rolled. Carbon and alloy steel ingots are poured and forged at a Seattle plant into ship shafting, drive shafts, billets, slabs, bars, rings, hooks, and other items. Static, shell, investment, and centrifugal castings are produced at 19 steel foundries in a wide range of steel specifications. All Pacific Northwest steel output is based on remelting steel scrap. Local iron ore might be used in the future to supplement steel scrap as a metal source. Ore reduction would probably be achieved by methods other than the blast furnace. Current melt-shop practice and problems are basically the same in Pacific Northwest steel plants as in cold-melt shops in other parts of the country. Quality steel production is receiving more emphasis in this region with the installation of modern analytical equipment and vacuum pouring and melting facilities.

Jan 1, 1962