Search Documents

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By Lisa A. McDonald

The environmental compliance process affects all aspects of hardrock-mining operations, from exploration through post-closure. The primary components of the environmental compliance process are requirements under the National Environmental Protection Act of 1969 (NEPA) and the permitting requirements associated with various other federal, state and local laws. This study considers the Greens Creek Mine and the development of two other projects (Alaska-Juneau & Kensington). These mines were used as the foundation for a case study of the impacts of the environmental compliance process on hardrock-mining activity in Southeast Alaska. The case study presents the institutional and legal requirements, followed by a discussion of the impact of this process on the production and timing of the three mines. The results of this preliminary study reveal some interesting findings, some expected and others unexpected, regarding the impact of the permitting process on the exploration, development and (proposed) operation of the three mining projects in the Juneau area. Determining the cost of compliance with these requirements is an important step in evaluating the appropriate course of action to protecting the environment while providing the necessary raw materials needed for society. This preliminary study highlights the initial starting point for such an analysis.

Jan 1, 1992

By C. M. McKinney

This report contains Bureau of Mines routine analyses of 492 samples of crude petroleum from 470 United States oilfields, each of which produced 2,500 barrels a day or more during at least 1 of the years 1946-56. The fields are listed alphabetically by State and field names in table 1, with information on the geographical and geological sources of the samples. Table 2 summarizes the general characteristics of the crude oils and analytical and computed data determined from the analyses. A previous report 4 contains similar analyses of 283 important United States oilfields; some of them are repeated in this report. Many fields for which analyses previously were published are represented by new analyses, which include data not previously reported. Refractive index nu and specific dispersion, ng minus nD divided by the density, for some of the distillate fractions are included in the analyses of 316 of the crude-oil samples. This is the first Bureau of Mines report on analysis of crude oils to contain such data, and their use in calculating hydrocarbon-type composition of the fractions is explained.

Jan 1, 1957

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing formation is very thick; ever modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has ,been developed systematically; and every effort has been made to utilize the reservoir energy efficiently. Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim of the study was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By Charles B. Carpenter

[The Bureau of Mines selected Anahuac for a petroleum-engineering study because it is one of the notable fields of the Gulf Coast region. It is outstanding because the producing for is very thick; every modern technique of drilling' and development has been applied; complete records of all operations,, including detailed subsurface information have been kept; the field has been developed systematically; and every effort has been made to utilize the reservoir energy efficiently Data and information pertaining to the development anal operation were collected, compiled, and studied by the writers as if the field were under single ownership. The chief aim-of the stud,, was to increase the accuracy of the existing methods of estimating reserves by applying all the data collected during the modern development of an oil-field, These scientific aids include coring; electric logging; micropaleontology determinations of porosity, permeability of oil-bearing sands, and their connate water content; subsurface sampling of the reservoir oil; and depth-pressure measurements. Because the reservoir structure in the Anahuac field is extremely complex, special attention was given to methods of calculating the reservoir volume.]

Jan 1, 1941

By N. A. Eilertsen

This paper presents the results of intermittent study begun in 1956 by the Federal Bureau of Mines of yieldable steel arches and yieldable steel ring sets installed for support of development openings in metal mines. Observations were made of this type of support in several iron mines in the northeast and north-central states. The sets, both arches and rings fabricated in the United States, are made from a hot-rolled, cold bent, structural U-shaped steel section in two weights, 15 pounds and 21 pounds per foot. The lighter section is generally used, It is 4.41 square inches in cross section area, and the calculation is that a 6-foot length of this structural shape installed as a supporting column, will safely carry the same load as a Douglas fir post of the same length but of 22 times the cross-sectional area of the steel.

Jan 1, 1962

Severe whipping of shuttle car trailing cables occurs when the car stops suddenly or reverses direction. This causes cable damage, and can seriously injure personnel near the cable. FMC has contracted with the U.S. Bureau of Mines to design, build and demonstrate a reel control system that will significantly reduce or eliminate whipping. II. CONCLUSIONS Results of engineering effort show that the following conditions are primarily responsible for the whipping problem. Causes may exist individually, or in combination.

Jan 1, 1972

By R. L. Benner

The Bureau of Mines investigated the ZnO-Fe2O3-Fe3O4 system at 1,000°, 1,300°, and 1,400° C, with oxygen pressures between 1.0 and lx10-4 atmospheres. The results, divided into the thermodynamic properties as related to the spinel structure, and the thermodynamic properties as related to zinc concentrate roasting, were used to calculate the activities of ZnO, Fe2O4, and Fe3O4 within the spinel solid solution region of the ternary system, and the pseudo-binary activities of ZnFe2O4 and Fe304. The activities of both systems show large positive deviations from Raoult's Law, especially at high Fe3O4 concentrations. The free energies, the enthalpies, and the entropies of mixing for the binary system were calculated from the binary activities, and the entropies of mixing were compared with two statistical models, one representing an ideal solution, and one representing the mixing of a normal with an inverse spinel. The binary entropy of mixing seemed to be better represented by the latter statistical model, indicating that the tetrahedral and octahedral cations of the reactants tend to remain in the product, even at the high temperatures of the study. This comparison also indicated that the cations of the components are the major contributing factors to the thermodynamic properties.

Jan 1, 1966

By Felix A. Vogel

Rutile concentrate, used in the manufacture of welding rode, smoke-screen chemicals, and alloys, is being produced by the Titanium Alloy Co. of Arkansas at its mine and. mill in Magnet Cove. The company estimates a substantial reserve of recoverable rutile. This is a new operation, and production figures are not known. Previous operations had stripped the placer material, leaving the underlying mineralized zone. INTRODUCTION This report describes the mining and milling; operations of the Titanium Alloy Co. of Arkansas. The property was examined by the author on March 4, 1942, and subsequent dates. J. A. Wood, general manager, was very helpful in supplying information.

Jan 1, 1944

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By C. H. Larsen

The results of a comprehensive investigation of conveyance arrestment devices (safety catches) in United States coal mines are presented. Availability and use, performance, inspection, maintenance, testing, procedures, and regulatory requirements were investigated. Information was obtained from equipment manufacturers, mine operators, and regulatory-agency personnel, as well as from studies of domestic and foreign mining safety regulations. Traditional mine hoists and commercial elevators for mine use were investigated. Results of this and an earlier study of wire-rope practice in United States coal mines show a continued need for conveyance arrestment devices. A wide variety of these devices are in use. Only two types have been proved reliable for stopping a conveyance without injuring passengers or equipment. These are elevator overspeed-actuated wedge-clamp (Type B) safeties and broken-rope-actuated devices for wooden guides using a single-tooth-dog design developed in Ontario as a braking element. Elevators are widely used in U. S. coal mines. When maintained according to American National Standards Institute (ANSI) Specifications A17. I and A17. 2, they appear to present no major arrestment problems. Of 42 coal-mine hoists used for man transport that were inspected, 30 are in vertical and 12 in inclined shafts. Twenty-four vertical shafts use wood guides; 6 use steel. The 12 inclined-shaft systems use flanged-wheel T-rail guidance. Two wood-guided vertical-shaft systems use the single-tooth Ontario-type dog; the other 22 use multi-toothed wedges, cams, or dogs that have been proved highly unreliable. The arrestment devices in the six steel-guided vertical-shaft systems and in six of the inclined-shaft systems cannot be evaluated because performance data are lacking. The remaining six inclined-shaft systems have no arrestment devices at all. Of the 36 hoists with arrestment devices, the devices of 16 are never tested, the devices of 10 are actuated periodically with the conveyance at rest, and the devices of the other 10 are actuated periodically with a slow-moving conveyance. Although high speed is as probable as low speed in an emergency and would provide the best test of arrestment capability, no tests are performed in the United States which demonstrate the ability of an arrestment device to stop a loaded conveyance from high speed. Mine operators indicate little confidence in their conveyance arrestment devices, and manufacturers recognize a need to improve their products. Neither state nor Federal regulations provide a guide to this improvement. Mine operators, manufacturers, and state and Federal regulatory agency personnel would welcome specific guidance. In view of this, a set of application, design, actuation, stopping-performance, and testing and inspection criteria is presented as a guide to eliminating the inadequacies of these devices. Recommendations are included for improving hoist controls and machinery directly affecting conveyance safety.

Jan 1, 1972

By Thomas O. Meyer

Laboratory test results are presented for the determination of elastic modulus made with the NX borehole jack. Determinations were made in massive pieces of aluminum so as to satisfy conditions of linear elasticity, homogeneity, and isotropy. Results indicate a large discrepancy (approximately 200 percent) betwen material modulus as determined by laboratory block-loading tests and that indicated by the jack under relatively ideal circumstances. Effects due to interface friction, finite block size, incomplete plate-bore contact, and other factors were examined and found not to be significant. Finite element results indicate that assumed loading conditions for the jack differ from those actually occurring, at least in materials of high elastic modulus (approximately 10 million psi), such as quartzite.

Jan 1, 1974

By John R. Bartels

This Bureau of Mines report describes the development of a preliminary design for a novel, protected, cab-shuttle car for use in working seam heights down to 40 in. Because of the severe restrictions imposed by low-coal operation, Mine Safety and Health Administration (MSHA) regulations only require canopy protection on shuttle cars operating in seam heights of 42 in or greater. MSHA routinely grants variances for canopy use in seams 48 in high or less. The design was generated by giving the operator needs equal priority as related to machine performance parameters. Cab-shuttle car concepts that led to the recommended design are described, along with criteria and testing used to evaluate their potential effectiveness.

Jan 1, 1988

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

Introduction Research has shown that when an emergency occurs, work-ers often do not get the information they need to take appropriate action. Important information about incidents is either not com-municated effectively or not at all to those affected by the event. The "Emergency Communication Triangle" safety talk focuses on the content of emergency warning messages. It presents a procedure using mental cues that can be used by senders and receivers of emergency warnings. The talk includes graphics for use during the presentation, as well as references for more information. Background Interviews with 48 miners who had escaped one of three different underground mine fires revealed that warning information provided to them was inadequate. Either insufficient information was provided to miners inby the fire areas or they failed to ask the questions needed to let them plan and execute an effective escape. Most of the miners who evacuated from these three mines did not have information that would allow them to make decisions about efficient escapes. The communication breakdown came from two directions: (1) the individuals providing the warning did not offer details about the situations even though some were known and (2) the individuals who received the warnings did not ask for clarification of the situation. The lack of information allowed miners to continue attempting to place cues into normal frameworks after they should have evaluated the situation as abnormal and threatening. The uncertainty created by the lack of information influenced their decision-making and therefore their actions. Approach Researchers at the NIOSH Pittsburgh Research Laboratory have developed a training intervention that can be used by senders and receivers of warnings during a mine emergency. This material was developed for use in short safety training sessions such as start-of-shift safety talks. The information can be presented in about 15 minutes. Although the illustrations were taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. How It Works During the safety talk, miners learn about the six categories of critical information that should be provided during emergency communications: Who, Where, What, Miners, Event, and Response. • Who: When reporting an emergency or receiving a warning, the first thing a miner must do is identify himself or herself. This is important because people react differently based on who gives them information. • Where: Giving or finding out the location of the problem is important. Of the 48 miners interviewed about their escape, only 2 knew where the fire was located. However, this information was known by either the dispatcher or the person who discovered the fire. • What: Miners must tell or ask exactly what is happening. At one mine fire, miners near the phone heard the message to evacuate and went to gather the others on their crew. One worker shouted to a machine operator: "Come on down to the mantrip. We're going out." Because it was close to quitting time, the machine operator thought they were just leaving the section a little early and went through his normal end-of-shift routine, wasting valuable time. After giving or obtaining the three initial pieces of critical information, miners can then give or obtain details about the response in progress. • Miners: Is anyone hurt? Has everyone been accounted for? When and where was a missing person last seen?

Sep 1, 2004