Search Documents

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract R0122026 (which began in August of 1971). Under this contract ADI provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

The coal reserve base is defined for coalbeds having sufficient thickness for underground mining within a depth range compatible with economic recovery. The reserve data are compiled by the Federal Bureau of Mines by updating and reevaluating previous estimates of the U.S. Geological Survey, State geological surveys, and others. Through the application of computer techniques, the tonnages are compiled by State, county, coalbed, and rank. Coal reserve base is allotted to sulfur categories by a statistical apportionment of data from available Bureau of Mines reports and records. The coal reserve base in those States east of the Mississippi River, minable by underground methods, is estimated to be 169 billion tons in coalbeds greater than 28 inches in thickness to a maximum depth of 1,000 feet. Excluding those coals in reliability categories other than measured and indicated, the underground reserve base includes 162 billion tons of bituminous coal and 7 billion tons of anthracite. Of the total, 27 billion tons contains 1.0 percent or less sulfur. Most of this low-sulfur coal is in the southern Appalachian area. Approximately 16 percent of the underground reserve base is without available analyses. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves. The purpose of this system is to provide a common yardstick for determining coal resources and reserves.

Jan 1, 1974

Reduce the number of accidents in which large mining trucks crush objects that were not visible to the driver. Approach Improved rear view mirrors, light-bending plastic lenses, and a closed circuit TV, are combined in a rugged system that allows the driver to see almost all areas around a large raining truck. How It Works Improved mirrors, used in place of ordinary left and right rear view mirrors, give wider angle viewing. Fresnel lenses, two mounted on the front edge of the hood and another one mounted above the right front fender, show objects close to the front and right side of the truck. A rugged closed circuit TV camera mounted above the rear axle reveals objects behind the truck. See diagrams showing reduction of blind area around a 150-ton mining truck. The improved mirrors for rear viewing are approximately rectangular. The left rear view mirror has a flat reflecting surface 10 inches wide by 20 inches high. The right rear view mirror is curved to give wider viewing angles, both from left to right and up and down. This mirror is 12 inches wide by 16 inches high. Its convex reflecting surface has the same curve as the surface

Jan 1, 1979

By Allan E. Martin

As part of a comprehensive investigation of tae mechanism of desulfurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of :lines, in cooperation with the Institute of Technology., University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FeXCay)S and (MnxCay)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in- situ, on rock mine pillars, arches, end other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigations4/ have shown that, the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in situ, on rock mine pillars, arches, and other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigators,4/ have shown that the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By Robert M. Baker

This document details the method whereby Allen Corporation of America gathered and analyzed data and developed an annotated bibliography of metal and nonmetal mine fire reports (1950-1979). The primary objective of this program was to develop the annotated bibliography which included MSHA accident reports and periodicals. Two additional objectives were to gather data on non-reportable fires and to conduct statistical analyses on the data to delineate trends. Data was acquired from three major areas: periodicals, MSHA fire reports, and mine safety directors. Data was separated into reportable fires (at least ½ - hour duration or injury), non-reportable fires, and opinion data. The data was then analyzed by time trends, state, ore, ignition source, burning substance, location, equipment, detection, duration, injuries, fatalities, and successful extinguishing agent. The authors make a number of recommendations: (1) improved stationary electrical equipment design and fire protection, (2) improved design of mobile equipment to separate combustibles from ignition sources, (3) improved maintenance, (4) improved housekeeping, and (5) improved training. The document is divided into two volumes and an appendix. Volume I contains data acquisition procedures, data analysis procedures, and conclusions and recommendations. Volume II contains a chronological list of mine fires and fifteen indexes to assist the reader in locating fire incident report of interest. The Appendix contains the annotated bibliography of over 300 metal and nonmetal mine fire reports and journal articles and a list of non-reportable fires.

Jan 1, 1980

By Luis v. Coppa

Since its inception in 1910, the Bureau of Mines has been the principal Federal agency involved in ore reserve estimations, using such traditional methods as polygons of influence and variations of inverse distance weighting While adequate for estimating the average are grades in a mining block or section, these methods do mot, however, provide a consistent way of quantifying the reliability of the estimates. This report describes a technique for enhancing ore reserve estimations using geostatistics, the methodology of which combines the spatial and random aspects of geologic phenomena into a formal theoretical framework for deriving the estimation variance of ore reserves. Correctly used, geostatistics enables confidence intervals to be placed around ore reserve estimates calculated from drill hole data. A geostatistical software system was obtained -From the U.S. Geological Survey and installed, aster slight modifications, on the Bureau's Wang computer. System testing and validation was conducted using a simple cast-book-type example. This was then followed by variogram analysis, point kriging and block kriging of data from a previously worked section of a uranium mine.

Jan 1, 1984

By B. J. Moore

The Bureau of Mines has estimated helium resources of the United States at 727 billion cubic feet as of January 1, 1979. These resources are divided into four categories in decreasing degrees of assurance of their existence: (1) Helium in storage and in measured natural gas reserves, 185 billion cubic feet; (2) helium in indicated natural gas resources, 150 billion cubic feet; (3) helium In hypothetical natural gas resources, 186 billion cubic feet; and (4) helium in speculative natural gas resources that makes up the remaining 206 billion cubic feet. The identified helium reserves, which are made up of that in measured and indicated natural gas categories, are further divided into depleting, non- depleting, and stored classifications. The depleting resources are those that are associated with natural gasfields that are, or will be, produced for the natural gas they contain. All of the helium in undiscovered natural gas resources are included in this classification. These depleting resources comprise 600 billion cubic feet of the total resource base. The nondepleting helium resources are estimted tototal 88 billion cubic feet. There is 39 billion cubic feet of helium in storage in Cliffside gasfield near Amarillo, Tex.

Jan 1, 1980

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By W. M. Myers

Jet is a substance of organic origin and has been defined by the U. S. Geological Survey as a "dense black lignite, taking a good polish, and sometimes used for jewelry". Jet is characterized by the lustrous, intense black surface it displays when polished. It is due to this property that the expression "jet black" is so commonly used to imply intense blackness.

Jan 1, 1923

By J. R. Thoenen

This circular is the third of a series summarizing the technical problems involved in the production and preparation of sand and gravel. The first, Information Circular 6668, published in December 1932, discussed the problems involved in prospecting and exploration. The second, Information Circular 6689 (March 1933), dealt with the development of gravel deposits. This is part I of a paper designed to present a study of problems arising in the excavation of sand and revel and their delivery to the treatment plant. Other circulars are planned which will discuss preparation of the material for market, plant storage, and miscellaneous subject. Definitions For the purpose of this circular, excavation is defined as the recovery of sand and gravel from developed natural deposits and their delivery to a plant for market preparation.

Jan 1, 1934

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968